lock Seat Toledo 2012 Owner's Guide

98Lights and visibility
Parking lights*
Parking lights 
– Switch the ignition off.
– Move the turn signal lever ⇒ Fig. 58 ⇒ page 97 up or down to
turn on the right or left-hand parking lights respectively.
Parking light on both sides
– Turn the light switch ⇒ Fig. 55  ⇒ page 94 to position  and
engage the steering lock.
Note
● The parking lights  only work when the ignition is switched on.
● The parking light will not come on automatically on switching the igni-
tion off if the left or right-hand turn signal is left on. 
Front fog lights with CORNER function*
Front fog lights with CORNER function provide better lighting of the area
around the car when driving through a corner or parking, etc.
Front fog lights with CORNER function switch on depending on how far you
turn the steering wheel or whether or not the turn signals 1)
are switched on,
if the following conditions are met:
● The vehicle is stationary, the ignition is switched on or you are moving
at a speed less than 40 km/h (25 mph)
● The daytime driving light is switched off ●
The dipped beam is switched on
● The fog lights are switched off
● Reverse gear is not engaged 
Hazard warning light switch
Fig. 59 Instrument pan-
el: switch for hazard
warning lights
– Press the button  ⇒ Fig. 59 to switch the hazard warning
lights on or off.
The warning lamps on the instrument panel and the warning lamp in the
switch will flash at the same time as the turn signals when the hazard warn-
ing lights are switched on. The hazard warning lights also work when the
ignition is switched off.
The hazard warning lights come on automatically in the event of an accident
in which an airbag is triggered. 
1)
In the event of a conflict between both functions, i.e. if you turn the steering wheel to the
left while the right-hand turn signal is on, the turn signals will take priority.

99
Lights and visibility
Note
Switch on the hazard warning lights to warn other road users, for example:
● When reaching the tail end of a traffic jam
● If the vehicle has a technical fault or you are involved in an emergency
situation. 
Interior lights
Interior lighting – version 1
Fig. 60 Interior lighting
– version 1
Switching on the interior light
– Move the switch A
⇒ Fig. 60 towards the side of the light. The
symbol  will be displayed.
Switching off the interior light
– Move the switch A

⇒ 
Fig. 60 to the centre position O
. Operating the courtesy light
–
Move the switch A
⇒ Fig. 60 to the centre of the light. The sym-
bol  will be displayed.
Reading lights
– The reading lights are switched on and off by pressing switch
B
⇒ Fig. 60.
Where the courtesy light is on (switch A
⇒ Fig. 60 in position ), the light
will come on if:
● The vehicle is unlocked
● One of the doors is opened
● The key is removed from the ignition
When the courtesy light is on (switch A
in position ), the light will switch
off if:
● The vehicle is locked
● The ignition is switched on
● 30 seconds after all of the doors have been closed
If a door is left open or if switch A
is in position
, the interior lighting is
switched off after about 10 minutes to prevent the battery from running flat. 
Safety FirstOperating instructionsPractical TipsTechnical specifications

105
Lights and visibility
Set the windscreen wiper arms to the service position before
changing the blades.
Service position for changing wiper blades
– Close the bonnet.
– Switch the ignition on and off.
– Press the lever to position 4
⇒ Fig. 66 ⇒ page 103, the wind-
screen wiper arms are set to the service position.
Taking off the wiper blade
– Lift the windscreen wiper arm away from the glass moving the
blade slightly in the direction of the arm – arrow A
⇒ Fig. 67.
– Hold the top of the windscreen wiper arm with one hand.
– Unlock the catch 1
with the other hand and remove the blade
in the direction of arrow B.
Fitting the wiper blade
– Slide the blade fully until it clicks into position.
– Check that the wiper is correctly secured.
– Fold the windscreen wiper arm back down onto the glass.
– Switch the ignition on and press the lever to position 4
⇒ Fig. 66 ⇒ 
page 103, the windscreen wiper arms are set to the
basic position. Changing the rear window wiper blade
Fig. 68 Rear window
wiper blade
Taking off the wiper blade
– Lift the rear window wiper arm away from the glass moving the
blade slightly in the direction of the arm – arrow A
⇒ Fig. 68.
– Hold the top of the rear window wiper arm with one hand.
– Unlock the catch 1
with the other hand and remove the blade
in the direction of arrow B.
Fitting the wiper blade
– Slide the blade fully until it clicks into position.
– Check that the wiper is correctly secured.
– Fold the rear window wiper arm back down onto the glass. 
Safety FirstOperating instructionsPractical TipsTechnical specifications

107
Seats and storage
Seats and storage Front seats
Introduction
Set the driver seat in such a way that the pedals can be fully depressed with
your legs slightly bent.
Set the driver seat backrest in such a way that the upper point of the steer-
ing wheel can be reached with your arms slightly bent.
The correct seat position is very important for:
● Reaching all of the controls safely and quickly
● A relaxed low-fatigue posture
● maximum protection from the seat belts and airbag system
WARNING
● Adjust the driver seat only when the vehicle is stationary. Risk of ac-
cident!
● Be careful when adjusting the front seats! Careless and uncontrolled
adjustment can cause injuries.
● The backrests must not be reclined too far back while driving. This
could limit the effect of the seat belts and the airbag system. Risk of in-
jury!
● Never transport more that the permitted amount of people in your ve-
hicle.
WARNING (Continued)
● Every occupant in the vehicle must properly fasten and wear the seat
belt belonging to his or her seat. Children must be protected with an ap-
propriate child restraint system ⇒ page 45, Child safety.
● The front seats, head restraints and seat belts must always be adjus-
ted to the size of the vehicle occupant to provide you and your passen-
gers with the greatest possible protection.
● Your feet should remain in the footwell while the vehicle is moving;
never rest them on the dash panel, on the window or on the seat! This
also applies to passengers. An incorrect sitting position exposes you to
an increased risk of injury in case of a sudden braking or an accident. If
the airbag is triggered, you could sustain severe injuries due to an incor-
rect sitting position!
● It is important for the driver and front passenger to keep a distance of
at least 25 cm from the steering wheel and dash panel. Failure to respect
the minimum distance means that the airbag will not protect you. Risk of
fatal injury if triggered!
● No items must not be kept in the footwell, as they could block the
pedals in the event of a sudden braking manoeuvre or change of direc-
tion. You would no longer be able to brake, change gear or accelerate.
● Do not place any items on the front passenger seat other than those
allowed (e.g. child seat). Risk of accident!
Note
After a certain time, the backrest angle adjustment mechanism may gain a
certain amount of play. 
Safety FirstOperating instructionsPractical TipsTechnical specifications

110Seats and storage
Head restraints cannot be moved up or down or removed on sports
seats.
Adjusting height
–Take hold of the sides of the head restraint and pull upwards.
– To lower the hear restraint, press button A
⇒ Fig. 73 while
pushing the head restraint downwards.
Fitting and removing head restraints on front seats
– Push the head restraint up as far as it will go.
– Press catch A
⇒ Fig. 73 and remove the head restraint.
– To refit, insert the head restraint into the holes in the backrest,
pushing it down until it engages.
Fitting and removing head restraints on rear seats
– Push the head restraint up as far as it will go.
– Press catch 1
⇒ Fig. 73 while pressing on the catch in hole 2with a max. 5 mm flat-headed screwdriver and remove the head
restraint.
– To refit, insert the head restraint into the holes in the backrest,
pushing it down until it engages.
For maximum head restraint protection, adjust the head restraint so that its
upper edge is at the same level as the top of your head.
The head restraint must be adjusted in line with the height of users. Correct
adjustment of the head restraint, together with the seat belts, ensure effec-
tive passenger protection ⇒ page 10.
WARNING
● Badly adjusted head restraints increase the risk of injuries in the
event of an accident.
● Never drive with the head restraints removed. Risk of injuries!
● If the seats are in use, never drive with the rear head restraints in
their out-of-use position.

Rear seats
Folding the rear backrest
Fig. 74 Unlocking the backrest 

111
Seats and storage
Folding
– Before folding the rear seats, adjust the position of the front
seats so that they cannot be damaged by the rear seats 1)
.
– Insert the seat belt latch plate into hole A
⇒ Fig. 74 located on
the corresponding side of the vehicle – safety position.
– Press the lock button B
to unlock the backrest and fold it for-
wards.
Returning to the initial position
– Where the head restraint has been removed, insert it into the
backrest when partially raised.
– Push the backrest backwards to its original position until the
lock button engages – check that it is locked by pulling on the
backrest ⇒ 
.
– Make sure the red protruding part C
is not visible.
WARNING
● Once the backrests have been lifted, the seat belts and their buckles
must be in their initial position – ready for use.
● The backrests must be safely locked to ensure any items in the lug-
gage compartment cannot move around the interior of the vehicle in the
event of a sudden braking manoeuvre. Risk of injuries!
● Make sure the rear backrests are correctly locked. Only then will the
three-point automatic seat belt on the rear central seat work correctly.
CAUTION
Take care when handling the rear backrests so as not to damage the seat
belts. The seat belt must never be left behind the lifted backrest. 
Armrest on rear seats
Fig. 75 Rear seats: arm-
rest
The armrest can be folded away for greater comfort using the handle
⇒  Fig. 75. 
1)
When the front seats are adjusted to the rear position, their head restraints should be re-
moved before folding the backrests on the rear seats. Store the removed head restraints in
such a way that they cannot be soiled or damaged.
Safety FirstOperating instructionsPractical TipsTechnical specifications

127
Heating and air conditioning
Heating Operation
Fig. 98 Heating: controls
Temperature selection
– Turn rotary control A
⇒ Fig. 98 clockwise to increase the tem-
perature.
– Turn rotary control A
anti-clockwise to reduce the temperature.
Blower selection
– Turn rotary control B
⇒ Fig. 98 to position 1 to 4 to switch the
blower on.
– Turn rotary control B
to position 0 to switch the blower off.
– Press button 1
⇒  in Air recirculation on page 129 to close
the fresh air vent. Air distribution selection
–
Turn rotary control C
⇒ Fig. 98 to select the air vents
⇒ page 126, Air vents you wish to activate.
All controls, except control B
⇒ Fig. 98, can be set to any intermediate po-
sition.
Leave the blower activated at all times to prevent the windows from misting
over.
Note
If the system is set so that all of the air is used to defrost the windows, no
air is supplied to the footwell area. This could limit heating comfort. 
Safety FirstOperating instructionsPractical TipsTechnical specifications

128Heating and air conditioning
Heating selection
Recommended settings for the different modes:
SettingsControl positionbutton 1Air vents 4ABC
Windscreen and side window de-
frostClockwise as far as it
will go3Do not switch onOpen and direct towards the side window
Windscreen and side window de-
frostRequired tempera-ture2 or 3  Do not switch onOpen and direct towards the side window
Heat as quickly as possibleClockwise as far as itwill go3Switch on brieflyOpen
Mild heatingRequired tempera- ture2 or 3  Do not switch onOpen
Fresh air mode - blowerAnti-clockwise as faras it will goRequired positionDo not switch onOpen
Note
● Controls A ⇒ Fig. 98 ⇒ page 127, B, C and button 1.
● Air vents 4 ⇒ page 126.
● We recommend you leave the air vents 3 ⇒ page 126 in the open posi-
tion. 
Air recirculation
Air recirculation prevents unpleasant smells, e.g. when passing
through a tunnel or in queuing traffic, from entering the interior. Switching on air recirculation mode
–
Press button 

1 ⇒ Fig. 98 ⇒ page 127 and the lamp in the
button will light up.
Switching off air recirculation mode
– Press button 

1 ⇒ Fig. 98 ⇒ page 127 again and the lamp
in the button will switch off.
If air vent C
⇒ Fig. 98 ⇒ 
page 127 is in position
, air recirculation
mode switches off automatically. Press the  button to switch air recircula-
tion mode back on in this position. 

129
Heating and air conditioning
WARNING
Never use the air recirculation system for too long, as it prevents fresh air
from entering the vehicle and “used” air can cause tiredness, reduce your
attention span and cause the windows to mist over. This increases the
risk of an accident. Switch off the air recirculation system as soon as the
windows begin to mist over.

Air conditioning (manual)* General notes
The air cooling system only works if the AC button
2 ⇒ Fig. 99
⇒ page 129 is pressed and under following conditions:
● The engine is running
● The outside temperature is above +2 °C (+36 °F)
● The blower control is in position 1 – 4
When the cooling system is on and under certain conditions, air can be
blown from the vents at a temperature of approx. 5 °C (41 °F). In the event
of prolonged, irregular distribution of the air flow from the outlets and sig-
nificant differences in temperature, e.g. on leaving the vehicle, sensitive
people may catch a cold.
Note
A visit to the specialised service once a year is recommended to clean the
air conditioning system. Operation
Fig. 99 Air conditioning: controls
Temperature selection
– Turn rotary control A
⇒ Fig. 99 clockwise to increase the tem-
perature.
– Turn rotary control A
anti-clockwise to reduce the temperature.
Blower selection
– Turn rotary control B
⇒ Fig. 99 to position 1 to 4 to switch the
blower on.
– Turn rotary control B
to position 0 to switch the blower off.
– Press button 

1 ⇒ page 131, Air recirculation to close the
fresh air vent.
Air distribution selection
– Turn rotary control C
⇒ Fig. 99 to select the air vents
⇒ page 126 you wish to activate. 
Safety FirstOperating instructionsPractical TipsTechnical specifications

131
Heating and air conditioning
Air conditioning selection
Basic air conditioning control settings recommended for the corresponding
operating modes:
SettingsControl positionButtonAir vents 4ABC12
Windscreen and side window
defrost a)Required temper-
ature3 or 4Do not switch onSwitched on automat- icallyb)Open and direct towards
the side window
Heat as quickly as possibleClockwise as faras it will go3Switch on brieflyOffOpen
Mild heatingRequired temper- ature2 or 3  Do not switch onOffOpen
Heat as quickly as possibleAnti-clockwise as
far as it will goBriefly 4, then 2 or 3Switch on briefly c)OnOpen
Optimum coolingRequired temper-
ature1 or 2, respec-tively. 3Do not switch onOnOpen and direct towards the roof
Fresh air mode - blowerAnti-clockwise asfar as it will goRequired posi- tionDo not switch onOffOpen
a)This type of setting is not recommended in countries with high air humidity. The windows could cool too quickly and cause them to mist over on the outside.
b) The lamp in button 2 lights up, even if not all of the conditions for cooling system operations are met. Cooling is indicated as available once all of the conditions are met
⇒ page 129, General
notes.
c) In certain conditions, air recirculation mode can switch on automatically ⇒ page 131, a lamp lights up in the 
button.
Note
● Controls A ⇒ Fig. 99 ⇒ page 129, B, C and buttons 1 and 2.
● Air vents 4 ⇒ page 126.
● We recommend you leave the air vents 3 ⇒ page 126 in the open posi-
tion. Air recirculationAir recirculation prevents unpleasant smells, e.g. when passing
through a tunnel or in queuing traffic, from entering the interior.
Switching on air recirculation mode
–
Press button 

1 ⇒ Fig. 99 ⇒ page 129 and the lamp in the
button will light up. 
Safety FirstOperating instructionsPractical TipsTechnical specifications