engine Seat Toledo 2014 Repair Manual

Fuses and bulbs
Changing fuses in the engine
compartment Fig. 140
Battery: fuse cover (version 1). Fig. 141
Battery: fuse cover (version 2). ●
Press the flexible tabs on the fuse box cov-
er in the direction indicated by the arrows 1 ›››
Fig. 140 .
● Remo
ve the cover by sliding it in the direc-
tion indicated by arrow 2 .
● Use a flat-headed screwdriver to unlock the
holes 3 .
● Open the cover in the direction indicated
by the arrow 4 .Replacing a blown fuse
Fig. 142
Image of a blown fuse Preparation
● Switch off the ignition, lights and all elec-
trical equipment.
● Open the corresponding fuse box
››› page 164 .
Identif y

ing a blown fuse
A fuse is blown if its metal strip is ruptured
››› Fig. 142.
Point a lamp at the fuse. This will make it
easier to see if the fuse is blown.
To replace a fuse ● Remove the fuse.
● Replace the blown fuse by one with an
identical amperage rating (same colour and
mark

ings) and identical size ››› .
»
165
Technical specifications
Advice
Operation
Safety

Advice
● Replace the cover again or close the fuse
box lid. CAUTION
If you replace a fuse with higher-rating fuse,
you could cause damage to another part of
the electrical system. Changing bulbs
Introduction Changing bulbs requires a certain degree of
practical skill. If in doubt, we recommend you
have defective bulbs changed by a special-
ised service or, in case of an emergency,
seek professional assistance.
●
Switch off the ignition and all of the lights
before changing a bulb.
● Do not touch the glass part of the bulb with
your bare hands. The fingerprints left on the
glass will vaporise as a result of the heat gen-
erated by the bulb, reducing bulb life and
causing condensation on the reflector sur-
face, thus reducing effectiveness.
● A bulb must only be replaced by one of the
same type. The type is indicated on the bulb,
either on the glass part or on the base.
● There is a storage area for the bulb box in
the spare wheel well or below the carpet in
the luggage compartment. The light source used for each function is lis-
ted below:
Double headlights
H7 Long Life
H7
W5W Long Life PY21W NA P21W Super Long Life WARNING
● Take particular care when working on com-
ponents in the engine compartment if the en-
gine is warm. Risk of burns.
● Bulbs are highly sensitive to pressure. The
glass can break when you touch the bulb,
causing injury.
● The high voltage element of gas discharge
bulbs* (xenon light) must be handled correct-
ly. Otherwise, there is a risk of death.
● When changing bulbs, please take care not
to injure yourself on sharp parts in the head-
light housing. CAUTION
● Remove the ignition key before working on
the electric system. Otherwise, a short circuit
could occur.
● Switch off the lights and the parking light
before changing a bulb. Dipped beam:
Main beam:
Side lights:
Turn signals:
Daytime driving lights: For the sake of the environment
Please ask your specialist retailer how to dis-
pose of used bulbs in the proper manner. Note
● Depending on weather conditions (cold or
wet), the front lights, the fog lights, the rear
lights and the turn signals may be temporari-
ly misted. This has no influence on the useful
life of the lighting system. By switching on
the lights, the area through which the beam
of light is projected will quickly be demisted.
However, the edges may continue to be mis-
ted.
● Please check at regular intervals that all
lighting (especially the exterior lighting) on
your vehicle is functioning properly. This is
not only in the interest of your own safety,
but also that of all other road users.
● Before changing a bulb, make sure you
have the correct new bulb.
● Do not touch the glass part of the bulb with
your bare hands, use a cloth or paper towel
instead. Otherwise, the fingerprints left on
the glass will vaporise as a result of the heat
generated by the bulb, they will be deposited
on the reflector and damage its surface. 166

Technical specifications
Technical specifications
Technical specifications
Important information Important The information in the vehicle documentation
always takes precedence over the informa-
tion in this Instruction Manual.
All technical specifications provided in this
documentation are valid for the standard
model in Spain. The vehicle data card inclu-
ded in the Maintenance Programme or the
vehicle registration documents shows which
engine is installed in the vehicle.
The figures may be different depending
whether additional equipment is fitted, for
different models, for special vehicles and for
other countries.
Abbreviations used in the Technical
Specifications sectionAbbrevia-
tionMeaning
kWKilowatt, engine power measurement.
PSPferdestärke (horsepower), formerly
used to denote engine power.
Abbrevia-tionMeaning
rpmRevolutions per minute - engine speed.
NmNewton metres, unit of engine torque.
litres per100 kmFuel consumption in litres per 100 km
(70 miles).
g/kmCarbon dioxide emissions in grams per
km (mile) travelled.
CO 2Carbon dioxide
CNCetane number, indication of the diesel
combustion power.
RONResearch octane number, indication of
the knock resistance of petrol. Vehicle identification data on the data
sticker
Fig. 164
Data sticker. Fig. 165
Identification plate Vehicle data sticker
The vehicle data sticker
››› Fig. 164 is located
on the boot floor and i

s also attached to the
Maintenance Programme.
The following information is provided on the
vehicle data sticker:
Vehicle identification number (VIN)
Vehicle model
Identifying letters of the gearbox/number
of the original paint finish/Interior equip-
ment number/engine power/engine
identifying letter
Partial description of the vehicle
Weight in running order
Fuel consumption (in litres per 100 km) –
urban/on the motorway/combined
Combined CO 2 emissions (g/km)
1 2
3
4
5
6
7
174

Technical specifications
Type plate
The type plate ››› Fig. 165 is located at the
bott om of
the front driver side door pillar be-
tween the front and rear doors.
The type plate indicates the following
weights:
Total permitted weight of the vehicle
when loaded
Maximum authorised weight of the vehi-
cle with a trailer, when the vehicle oper-
ates as a tractor
Maximum permitted load of the front axle
Maximum permitted load of the rear axle
Weight in running order
The weight in running order only has one ap-
proximate value. This value corresponds to
the minimum operative weight of the vehicle
without additional equipment that increases
its weight, i.e. air conditioning, spare wheel,
towing bracket.
The running order weight also includes 75 kg
of the weight of the driver and service fluids,
in addition to a fuel tank at 90% capacity.
From the difference between the total permit-
ted weight in running order the approximate
carrying capacity can be calculated ››› .
The carrying capacity must include:
● occupants,
8 9
10
11 ●
all pieces of equipment and other weights,
● roof loads including the roof rack,
● equipment that is not included in the run-
ning order weight,
● when using the towing bracket, the draw-
bar load (max. 50 kg)
Calculating fuel consumption and CO 2
emissions according to the ECE regulations
and the EU specifications
Calculation of fuel consumption for urban
driving begins when cold-starting the engine.
Then, normal city driving is simulated.
In calculating extra-urban driving fuel con-
sumption, braking and acceleration is done
in all gears, as in daily use of the vehicle.
Driving speed varies within a range of 0 and
120 km/h (75 mph).
The consumption value in combined driving
is composed of 37% of the value of urban
driving and 63% of the value of extra-urban
driving. WARNING
The maximum permitted weight values must
not be exceeded – Risk of an accident and
damage to the vehicle! Note
● If you wish to calculate the exact weight of
your vehicle please contact a SEAT dealer. ●
Depending on the volume of equipment,
driving style, road conditions, weather condi-
tions and the condition of the vehicle, con-
sumption values can differ from the theoreti-
cal values stated here. Information on fuel
consumption
Fuel consumption The consumption and emission details
shown on the vehicle data sticker differ from
one vehicle to another.
Vehicle fuel consumption and CO
2 emissions
appear on the vehicle data sticker in the
spare wheel well, inside the boot and on the
rear cover of the Maintenance Programme.
The fuel consumption and CO 2 emission val-
ues refer to the weight category assigned to
your vehicle according to the engine and
gearbox combination, as well as the specific
equipment fitted, and is only used to com-
pare between the different models.
The fuel consumption and CO 2 emissions do
not depend only on the performance of the
vehicle, they can also differ from the estab-
lished values depending on other factors
such as driving style, road conditions, traffic
conditions, environmental conditions, load
and number of passengers. »
175
Technical specifications
Advice
Operation
Safety

Technical specifications
Engine data Petrol engine 1.2 55 kW (75 PS)Power output in kW (PS) at rpmMaximum torque (Nm at rpm)No. of cylinders/displacement (cm 3
)Fuel
55 (75)/5,400112/3,7503/1,198Super 95 RON/Normal 91 RON a)
a)
Slight power loss.
Performance
Top speed (km/h)175 (5)
Acceleration from 0-80 km/h (seconds)9.3
Acceleration from 0-100 km/h (seconds)13.9
Consumption (l/100 km)/ CO 2 (g/km)
Urban cycle8.1/187
Extra-urban cycle4.6/107
Combined5.9/137
Weights (in kg)
Gross vehicle weight1,595
Weight in running order (with driver)1,135
Gross front axle weight / Gross rear axle weight800 / 830
Permitted roof load75
Maximum trailer weights (in kg)
Trailer without brakes560
Trailer with brakes, gradients up to 8%950 178

Technical specifications
Petrol engine 1.2 TSI 63 kW (85 PS)Power output in kW (PS) at rpmMaximum torque (Nm at rpm)No. of cylinders/displacement (cm 3
)Fuel
63 (85)/4,800160/1,500-3,5004/1,197Super 95 RON/Normal 91 RON a)
a)
Slight power loss.
Performance
Top speed (km/h)183 (5)
Acceleration from 0-80 km/h (seconds)7.6
Acceleration from 0-100 km/h (seconds)11.8
Consumption (l/100 km)/ CO 2 (g/km) Ecomotive
Urban cycle6.5/1515.9/137
Extra-urban cycle4.4/1034.3/100
Combined5.1/1194.9/114
Weights (in kg)
Gross vehicle weight1,615
Weight in running order (with driver)1,155
Gross front axle weight / Gross rear axle weight820 / 830
Permitted roof load75
Maximum trailer weights (in kg)
Trailer without brakes570
Trailer with brakes, gradients up to 8%1,100
Trailer with brakes, gradients up to 12%900 180

Technical specifications
Petrol engine 1.2 TSI 77 kW (105 PS)Power output in kW (PS) at rpmMaximum torque (Nm at rpm)No. of cylinders/displacement (cm 3
)Fuel
77 (105)/5,000175/1,550-4,1004/1,197Super 95 RON/Normal 91 RON a)
a)
Slight power loss.
Performance
Top speed (km/h)195 (5)
Acceleration from 0-80 km/h (seconds)7.1
Acceleration from 0-100 km/h (seconds)10.3
Consumption (l/100 km)/ CO 2 (g/km)without Start-Stopwith Start-Stopwith Start-Stop +
185 tyre
Urban cycle6.9/1606.4/1496.3/146
Extra-urban cycle4.6/1074.3/1004.2/98
Combined5.4/1255.1/1185/116
Weights (in kg)
Gross vehicle weight1,635
Weight in running order (with driver)1,175
Gross front axle weight / Gross rear axle weight840 / 830
Permitted roof load75
Maximum trailer weights (in kg)
Trailer without brakes580
Trailer with brakes, gradients up to 8%1,200
Trailer with brakes, gradients up to 12%1,100 181
Technical specifications
Advice
Operation
Safety

Technical specifications
Petrol engine 1.6 77 kW (105 PS)Power output in kW (PS) at rpmMaximum torque (Nm at rpm)No. of cylinders/displacement (cm 3
)Fuel
77 (105)/5,600153/3,8004/1,598Super 95 RON/Normal 91 RON a)
a)
Slight power loss.
Performance AQ
Top speed (km/h)193 (5)192 (5)
Acceleration from 0-80 km/h (seconds)7.28.1
Acceleration from 0-100 km/h (seconds)10.611.9
Consumption (l/100 km)/ CO 2 (g/km)
Urban cycle8.9/21210.2/244
Extra-urban cycle4.9/1166/143
Combined6.4/1527.5/180
Weights (in kg)
Gross vehicle weight1,6151,655
Weight in running order (with driver)1,1551,195
Gross front axle weight / Gross rear axle weight820 / 830820 / 830
Permitted roof load7575
Maximum trailer weights (in kg)
Trailer without brakes570590
Trailer with brakes, gradients up to 8%1,2001,200
Trailer with brakes, gradients up to 12%1,0001,000 182

Technical specifications
Petrol engine 1.4 90 kW (122 PS) AutomaticPower output in kW (PS) at rpmMaximum torque (Nm at rpm)No. of cylinders/displacement (cm 3
)Fuel
90 (122)/5,000200/1,500-4,0004/1,390Super 95 RON/Normal 91 RON a)
a)
Slight power loss.
Performance
Top speed (km/h)206 (6)
Acceleration from 0-80 km/h (seconds)6.4
Acceleration from 0-100 km/h (seconds)9.5
Consumption (l/100 km)/ CO 2 (g/km)
Urban cycle7.4/172
Extra-urban cycle4.8/112
Combined5.8/134
Weights (in kg)
Gross vehicle weight1,690
Weight in running order (with driver)1,230
Gross front axle weight / Gross rear axle weight900 / 820
Permitted roof load75
Maximum trailer weights (in kg)
Trailer without brakes610
Trailer with brakes, gradients up to 8%1,200
Trailer with brakes, gradients up to 12%1,200 183
Technical specifications
Advice
Operation
Safety

Technical specifications
Diesel Engine 1.6 CR 66 kW (90 PS)Power output in kW (PS) at rpmMaximum torque (Nm at rpm)No. of cylinders/displacement (cm 3
)Fuel
66 (90)/4,200230/1,500-2,5004/1,598Diesel according to standard EN 590, min. 51 CN a)
a)
Cetane Number (cetane index) = Measure of the diesel combustion power.
PerformanceManualAutomatic
Top speed (km/h)184 (5)184 (6)
Acceleration from 0-80 km/h (seconds)7.97.9
Acceleration from 0-100 km/h (seconds)12.012.2
Consumption (l/100 km)/ CO 2 (g/km)
Urban cycle5.6/1475.6/146
Extra-urban cycle3.7/973.9/103
Combined4.4/1144.5/118
Weights (in kg)
Gross vehicle weight1,7251,745
Weight in running order (with driver)1,2651,285
Gross front axle weight / Gross rear axle weight930 / 830950 / 830
Permitted roof load7575
Maximum trailer weights (in kg)
Trailer without brakes630640
Trailer with brakes, gradients up to 8%1,2001,200
Trailer with brakes, gradients up to 12%1,2001,200 184