Steering wheel SKODA FABIA 2000 1.G / 6Y Workshop Manual

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
InspectionEdition 09.04
S00.5301.14.2002-2 page 1 02
02-2 Inspection
Pre-Delivery Inspection -PDI- (Export)
The operations marked with * apply to all countries; other
operations are applicable to certain countries only!
Compare as-delivered condition of vehicle with order form Chapter
♦Engine fitted
♦Type plate in the engine compartment
♦Vehicle data sticker (compare with stamped identification number)
♦Colour of paintwork, badges, inscriptions
♦Seats (cover, colour) interior trim (colour)
♦Radio, speakers, aerial
♦Central locking system, anti-theft alarm system
♦Wheels, tyres
♦Sun roof
♦Vehicle log book - for completion: Operating manual and service plan (in the correct lan-
guage and with the correct edition data), short introduction, technical data, support in the
case of a breakdown, other manuals (radio,...) ) - all in the vehicle log book pouch
♦Other equipment (all equipment fitted in proper condition)
* Check transport damage (bodywork, paintwork, upholstery, interior trim, carpeting, footmats,
tyres, wheels)02-5, 02-7
Vehicle (exterior)
–Check that all car keys and key number fobs have been provided; check that the sticker
for the key number for the electronic immobiliser is complete and legible
–Proper operation of door handles outside, door locks, child safety locks, door contact
switches and proper operation of all locks and keys (including spare keys), doors, boot lid/
tailgate, fuel filler cap, bonnet lock02-7
–Proper operation of anti-theft alarm system
Engine compartment (from above)
–Check battery no-load voltage, recharge battery if necessary02-6
–Check tight connection of electric cables and plug connections (in particular battery ca-
bles)
–Inspect engine, gearbox, cooling system, brake system and fuel system for leaks02-3, 02-5
–Engine oil level (in-between markings on dipstick)02-3
–Brake fluid level (at „MAX“ marking)02-5
–Coolant level (in-between marking), special equipment antifreeze down to -35°C02-3
–Fill up fluid in washer reservoir, in the winter add antifreeze
Vehicle interior
–Proper operation of seat belts, seat belt height adjuster, power windows and sun roof
–Check car tool kit, spare wheel and accessories for completeness and proper attachment
Underside of vehicle (on lift platform)
–Inspect underbody (underbody protection for damage)02-7
–Inspect for leaks and damage: Engine, gearbox, final drive, steering, brake system, axles,
joint boots. Check proper routing of the brake hoses and brake lines, fuel lines including
ventilation of the fuel system02-3, 02-5

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
InspectionEdition 09.04
S00.5301.14.2002-2 page 3 02
Delivery Inspection (Export)
–Proper operation of seat belts, seat belt height adjuster, power windows and sun roof
–Inspect upholstery, interior trim, carpeting and footmats for cleanliness and damage
–Inspect all switches, all electrical components, gauges/indicators and controls02-6
–Radio: Inspect for proper operation, store stations, set clock, encode02-6
–Reset service interval display02-6
–Power windows: Inspecting positioning02-6
–Key switch for airbag deactivation, front passenger side: Check function „ON/OFF“ and
switch-over to the position „ON“02-7
–Fit net in luggage compartment (if available)
–Check the car tool kit, spare wheel and accessories, that they have all been supplied and
are properly secured
–Install the carpets supplied in the vehicle
–Perform a test drive
Underside of vehicle (on lift platform)
–Inspect underbody (underbody protection for damage)02-7
–Inspect for leaks and damage: Engine, gearbox, final drive, steering, brake system, axles,
joint boots. Check proper routing of the brake hoses and brake lines, fuel lines including
ventilation of the fuel system02-3, 02-5
–Inspect tyres and wheels for damage02-5
Concluding operations
–Interrogate fault memory of all systems, if necessary erase02-6
–Remove protective seat covers
–Remove recharging table (if affixed)
–Complete the service schedule, affix the vehicle data sticker in the Service Schedule to
the floor of the luggage compartment next to the spare wheel„Next Service Date“ sticker
and affix to the side of the dash panel on the driver's side, hand the card „Škoda Assist-
ance“ to the customer02-7
–Final inspection to ensure proper condition for handover to the customer
Inspections and operations to be completed Chapter
Vehicle (exterior)
–Plastic and rubber parts: Inspect for cleanliness and damage
–Inspect bodywork and paintwork for damage02-7
–Check operation of the tailgate lock and the fuel filler cap, door contact switch, operation
of the door handles, door locks and safety buttons, central locking from outside as well as
inside, child safety locks, ability to close all locks on the vehicle using all keys (including
the spare key)02-7
–Check operation of the anti-theft alarm system
–Tighten the wheel bolts to specified torque (steel and light alloy wheels 120 Nm), fit wheel
caps02-5
–Check the tyre inflation pressure (including spare wheel), if necessary correct the tyre in-
flation pressure, fit valve caps02-5
–Vehicles in stock for more than 6 months: Change brake fluid02-5

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
InspectionEdition 09.04
S00.5301.14.2002-2 page 4 02
–Fit roof aerial
Engine compartment (from above)
–Check battery no-load voltage; recharge if necessary02-6
–Check tight connection of electric cables and plug connections (in particular battery ca-
bles)
–Brake fluid level (at „MAX“ marking)02-5
–Check the engine oil level (to be in-between the marking on the dipstick)02-3
–Check the coolant level (in-between marking), for special equipment antifreeze down to -
35 °C02-3
–Fill up fluid in washer reservoir, in the winter add antifreeze
–Check windscreen wiper and washer system, the spray nozzle adjustment and the resting
position of the windscreen wipers02-7
Vehicle interior
–Inspect upholstery, interior trim, carpeting and footmats for cleanliness and damage
–Inspect all switches, all electrical components, gauges/indicators and controls02-6
–Radio: Inspect for proper operation, store stations, encode, set clock02-6
–Fit net in luggage compartment (if available)
–Vehicle log book - for completion: Operating manual and service plan (in the correct lan-
guage and with the correct edition data), short introduction, technical data, support in the
case of a breakdown, other manuals (radio,...) ) - all in the vehicle log book pouch
–Reset service interval display02-6
–Power windows: Inspecting positioning02-6
–Key switch for airbag deactivation, front passenger side: Check function „ON/OFF“ and
switch-over to the position „ON“02-7
Underside of vehicle (on lift platform)
–Inspect underbody (underbody protection for damage)02-7
–Inspect for leaks and damage: Engine, gearbox, final drive, steering, brake system, axles,
joint boots. Check proper routing of the brake hoses and brake lines, fuel lines including
ventilation of the fuel system02-3, 02-5
–Inspect tyres and wheels for damage02-5
Concluding operations
–Perform a test drive02-9
–Interrogate fault memory of all systems, if necessary erase02-6
–Complete the service schedule, affix the vehicle data sticker in the Service Schedule to
the floor of the luggage compartment next to the spare wheel, complete the „Next Service
Date“ sticker and affix to the side of the dash panel on the driver's side02-7
–Remove recharging table (if affixed)
–Remove protective seat covers
–Install the carpets supplied in the vehicle
–Final inspection to ensure proper condition for handover to customer

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
InspectionEdition 09.04
S00.5301.14.2002-2 page 6 02
Every 30 000 km (QG0)
Includes: Annual inspection and additional operations stated in the table below
–Track rod ends: Inspect play and correct attachment of boots
–Check the tyre inflation pressure (including spare wheel), correct if necessary02-5
–Inspect tyre wear (including spare wheel)02-5
–Inspect tyre tread depth (including spare wheel) and record (FL..., FR..., RR..., RL...,
SP...)02-5
–Inspect exhaust system for leaks, damage and attachment
–Brake fluid volume: Check level, if necessary top up02-5
–Battery: test02-6
–Check the anti-freeze in the cooling system and record ...... °C, check for leaks, top up
coolant if necessary02-3
–Flap lock for the engine bonnet: grease
–Inspect operation of all switches, all electrical components, gauges/indicators and con-
trols for proper operation02-6
–Windscreen wiper and washer system: Inspect condition of wiper blades, wiper opera-
tion, washer system: if necessary top up fluid02-7
–Inspect plenum chamber for dirt, clean if necessary02-7
–Fuel filter: Drain away water (vehicles with diesel engine with fuel operation, which does
not comply with DIN EN 590-standard)02-3
–Inspect trailer coupling (with removable arm - manufacturer Profsvar)02-7
After each inspection
–Complete the „Next Service“ sticker and affix sticker to the side of the dash panel (on the
driver's side)
–Perform road test including inspection of proper operation of footbrakes and handbrake,
gearshift and steering, final inspection02-9
–„Mirror tag“ - complete and attach to interior mirror
–Hand customer the completed and signed form
Work involvedChapter
–Headlights: Inspect, if necessary adjust02-6
–Gear oil: Inspect level and top up if necessary (manual gearbox)02-4
–Fuel filter: Drain away water (vehicles with diesel engine with fuel operation, which does
not comply with DIN EN 590-standard)02-3
–Check underbody protection and body paintwork for damage02-7
–Dust and odour filter element for the passenger compartment: replace02-7
–Inspect operation of tilting roof and grease the runners02-7
–Inspect timing belt (petrol engines) - every 90 000 km, then every 30 000 km02-3

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
InspectionEdition 09.04
S00.5301.14.2002-2 page 9 02
–Check the tyre inflation pressure (including spare wheel), correct if necessary02-5
–Inspect tyre wear (including spare wheel)02-5
–Inspect tyre tread depth (including spare wheel) and record (FL..., FR..., RR..., RL...,
SP...)02-5
–Inspect exhaust system for leaks, damage and attachment
–Brake fluid volume: Check level, if necessary top up02-5
–Battery: test02-6
–Check the anti-freeze in the cooling system and record ...... °C, check for leaks, top up
coolant if necessary02-3
–Flap lock for the engine bonnet: grease
–Inspect operation of all switches, all electrical components, gauges/indicators and con-
trols for proper operation02-6
–Windscreen wiper and washer system: Inspect condition of wiper blades, wiper operation,
washer system: if necessary top up fluid02-7
–Inspect plenum chamber for dirt, clean if necessary02-7
–Inspect operation of tilting roof and grease the runners02-7
–Headlights: Inspect, if necessary adjust02-6
–Gear oil: Inspect level and top up if necessary (manual gearbox)02-4
–Draining the fuel filter (diesel engine)
–Inspect trailer coupling (with removable arm - manufacturer Profsvar)02-7
–Check underbody protection and body paintwork for damage02-7
–Dust and odour filter element for the passenger compartment: replace02-7
–Air filter: Clean the housing, replace the insert every 4 years or 60.000 km.02-3
–Replace the fuel filter (diesel engine with fuel operation, which does not comply with DIN
EN 590-standard)
–Ribbed V-belt: Inspect condition and for vehicles without tensioning pulley also the ten-
sion - every 60.000 km02-3
–Replace the fuel filter (diesel engine) - every 60.000 km
–Spark plugs: replace - every 60.000 km.02-3
–Automatic gearbox: Check the ATF level, and top up if necessary, every 60.000 km
–Check the timing belt for the camshaft on a 4-cylinder petrol engine at 90.000 km and
then every 30.000 km after that
–Replace the emergency battery for the alarm system - every five years02-6
After each inspection
–Complete the „Next Service“ sticker and affix sticker to the side of the dash panel (on the
driver's side)
–Perform road test including inspection of proper operation of footbrakes and handbrake,
gearshift and steering, final inspection02-9
–„Mirror tag“ - complete and attach to interior mirror
–Hand customer the completed and signed form Work involvedChapter

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
ChassisEdition 02.04
S00.5301.13.2002-5 page 3 02
–Remove strainer and clean.
–Use extraction device -1- to extract as much brake flu-
id as possible from the brake fluid reservoir.
–Fill the brake fluid reservoir with new brake fluid.
Vehicles fitted with a manual gearbox
–Fit hose of extraction device -Arrow- onto the bleeder
screw of the master cylinder -1-.
–Open the bleeder screw and by depressing the clutch
pedal allow approx. 0.1 litre of brake fluid to flow out.
–Secure the clutch with the brake pedal depressor, e.g.
-V.A.G 1869/2- in bottom position.
–Tightne bleeder screw and remove the hose.
–Put the clutch pedal in home position.
All vehicles
When changing the brake fluid it is necessary to replenish
the brake fluid reservoir with brake fluid.
–Fit hose of extraction device -1- onto the bleeder
screw of the rear right wheel.
1)
–Open the bleeder screw and by depressing the brake
pedal allow approx. 0.2 litres of brake fluid to flow out.
–Secure the clutch with the brake pedal depressor, e.g.
-V.A.G 1869/2- in bottom position.
–Tighten bleeder screw and remove the hose.
–Put the brake pedal in home position.
WARNING!
Drained (used) brake fluid must never be used
again.
Sequence: Wheel brake
cylinder, brale caliper,
clutch slave cylinderQuantity of brake fluid that
must flow out of the wheel
brake cylinders or brake
calipers and clutch slave
cylinder:
Rear right 0.2 litres
Rear left 0.2 litres
Front right 0.2 litres
Front left 0.2 litres
Clutch hydraulics 0.1 litres
1)On vehicles with right-hand steering: fit hose of extraction device onto the bleeder screw of the rear left wheel.
Note

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
BodyEdition 09.04
S00.5301.14.2002-7 page 1 02
02-7 Body
Airbag units: Visual inspection
Inspecting operation of airbag unit
When the ignition is switched on the airbag warning lamp
K75 lights up for approximately 4 seconds. Should the
warning lamp flash again for a further 12 seconds this is
an indication that the front passenger airbag or the side
airbag unit on the front passenger is electronically locked
(valid for vehicles which do not have an airbag switch-off
function).
The warning lamp will go out after 4 seconds for vehicles
which are fitted with an airbag switch-off function and
switching off of the front passenger airbag will be sig-
nalled by the warning lamp „AIRBAG OFF“ in the middle
of the dash panel.
♦If warning lamp K75 does not go out after 4 seconds
and lights up continously there is a fault.
♦If the warning lamp goes out and then lights up again
the control unit is not coded, the wrong control unit has
been fitted or there is a fault.
♦If the airbag warning light K75 flashes constantly, it is
then necessary to replace the airbag control unit J234.
If the warning light indicates a fault, the fault must be
rectified (repair measure) Body Work; Rep. Gr. 01.
Inspecting airbag for external damage
Driver and front passenger airbag units
The logo „AIRBAG“ on the padded boss of the steering
wheel (driver's side) and on the right side of the dash pan-
el (passenger side) indicates that an airbag is fitted.
–Carry out a visual inspection of the padded boss of the
steering wheel -1- and surface of the dash panel -2-
on the front passenger side for external damage.
–Undertake a visual inspection of the front seats to de-
termine any damage (valid for vehicles with side air-
bags).
♦Only use original seat upholstery approved for side
airbags.
♦The use of commercially available protective seat cov-
ers is prohibited as this impairs the operation of the
side airbags.
♦Replace all harpoon clips with new original parts.
♦In the event of damage to the upholstery - tears, burn
holes etc. - in the area of the side airbag always re-
place the upholstery with a new original part for safety
reasons.
1
S02-0297
2

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
BodyEdition 09.04
S00.5301.14.2002-7 page 2 02
Do not affix any stickers or cover over the padded boss of
the steering wheel -1- and the foam-lined surface of the
airbag unit on the front passenger side -2- or do not carry
out any modifications to these parts. These parts must
only be cleaned with a dry and slightly moistened cloth.
Inspect key switch for deactivation of
front passenger airbag
–Switch off ignition.
–Turn the key switch for deactivation of front passenger
airbag to the position „OFF“.
When the ignition is switched on the airbag warning lamp
must light up in the front interior light.
–Switch off ignition.
–Turn the key switch for deactivation of front passenger
airbag to the position „ON“.
After the ignition and the front passenger airbag is
switched on, the airbag warning light in the front interior
light must no longer light up after approx. 3 seconds.
Key switch for deactivation of front passenger airbag
must only be turned when ignition is switched off. If the
position of the switch is changed, the airbag control unit
can evaluate a fault; the individual contacts in the switch
make contact during different time intervals and subse-
quently the warning lamp lights up in the dash panel in-
sert (there is no risk of airbag activation).
Check underbody protection and body
paintwork for damage
The inspection of the underbody sealant and paintwork
should cover the following points:
1) undamaged layer of PVC Plastisol
–Vehicle floor
–Wings and wheel housings
–Sills
2) undamaged paintwork
–all body joints
–surround of windscreen
–surround of rear window
–flange of inner surfaces of engine hood
–horizontal and vertical painted surfaces
–Connection of the roof in the area of the luggage com-
partment lid
It is essential to rectify any defects found!
Note
Note

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
MiscellaneousEdition 06.01
S00.5301.06.2002-9 page 1 02
02-9 Miscellaneous
Tow starting/Towing
♦A towing rope or towing bar must only be fitted to the
above towing lugs.
♦The towing rope must be elastic to protect the vehicle.
Therefore only use synthetic ropes or ropes manufac-
tured in an equally elastic material. However, it is saf-
er to use a towing bar!
♦Make sure no unauthorised traction forces and no jolt-
ing loads are exerted. During towing manoeuvres
away from hardened road surfaces there is a risk of
overloading and damaging the fixation parts.
♦Before starting the engine by towing, first use the bat-
tery of another vehicle as a start aid.
Front: The threaded hole of the front towing lug is located
in the front right part of the bumper behind the cover grill.
Screw in the towing lug by hand by turning it to the left (in
the direction of the arrow) up to the stop.
Rear: The towing lug is located below the rear right part
of the bumper.
♦Comply with the legal regulations on towing.
♦Both drivers must be familiar with the specificities of
the towing process.
♦When using a towing rope the driver of the towing ve-
hicle must press the clutch very smoothly when driv-
ing off and changing gear.
♦The driver of the towed vehicle must make sure the
rope is kept taut.
♦The ignition must be switched on to ensure the steer-
ing wheel does not lock and the turn signals, horn,
windscreen wipers and windscreen washer system
can be activated.
♦As the brake servo unit only operates with the engine
running, the brake pedal must be pressed much hard-
er when the engine is switched off.
♦On vehicles with power steering the steering is much
harder when the engine is switched off.
♦If there is no lubricant in the gearbox or automatic
gearbox the vehicle must only be towed with the drive
wheels raised.
When towing vehicles with a manual gearbox
pay attention to the following:
–Before towing engage 2nd or 3rd gear.
–Switch on ignition.
Note
S02-0302
Note
Note

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
MiscellaneousEdition 06.01
S00.5301.06.2002-9 page 2 02
–As soon as the engine starts, press clutch and remove
gear to avoid driving into the towing vehicle.
Do not start the engine of vehicles fitted with an exhaust
catalyst by towing over a long distance as unburnt fuel
may get into the catalyst and burn there. This may result
in overheating and hence in the destruction of the cata-
lyst.
Perform a test drive
The following must be assessed within the scope of a test
drive according to the vehicle equipment and the availa-
ble possibilities (city/country, weather)
–Inspect engine for performance, misfiring, idling be-
haviour and acceleration.
–Foot and handbrake: Functional test (jerking, squeak-
ing, pulling to one side) ABS operation. Brake pedal-
idle travel: max.
1/3 of the idle travel.
–Inspect the lever position and smooth operation of the
gearshifts.
–Inspect the driving behaviour of the clutch as well as
the pedal force and smell.
–Inspect automatic gearbox: Selector lever position,
selector lever lock, shifting behaviour, display indica-
tion in dash panel insert.
–Inspect steering clearance of the vehicle standing on
its wheels, with engine running by turning the steering
wheel one way and then the other (wheels straight
ahead). There must be no play on the steering.
–Inspecting the sun roof operation.
–Pay attention to pulling and to the straigt ahead posi-
tion of the steering wheel during driving.
–Inspect the imbalance of the wheels, drive shafts and
propshafts.
–Inspecting functions: Heating, air conditioning, venti-
lation, instruments and warning lights, mirror adjust-
ment.
–Inspect engine, gearbox, axles, steering, brakes,
clutch, bodywork for abnormal noises
Raising the vehicle
Using a lift platform and a workshop jack
The vehicle must only be raised with a workshop jack in
the indicated jacking points -arrows-.
To avoid damage use a suitable rubber or wood insert.
Note
S02-0316