SKODA FABIA 2014 3.G / NJ Operating Instruction Manual

Downloaded from www.Manualslib.com manuals search engine ›Remove the protective cap D
» Fig. 194 on page 185 .›Turn the holder with the bulb in the direction of arrow 1 » Fig. 201 .›
Remove the holder with the bulb in the direction of arrow
2
.
›
Remove the bulb from the holder in the direction of the arrow
3
.
›
Insert a new bulb into the connector so that the lug
A
on the connector
snaps into the groove on the bulb.
›
Insert the connector with the new bulb into the headlight in the opposite di-
rection to the arrow
2
.
›
Turn the connector with the new bulb in the opposite direction to the arrow
1
until it stops.
›
Fit protective cap
D
» Fig. 194 on page 185 .
›
Replace the appropriate cover in the front wheel arch » page 185.
Replacing the high beam bulb (halogen projector headlights)
Fig. 202
Changing the bulb for the main beam
Read and observe
and on page 184 first.
Remove the holder of the wash water container nozzle before replacing the
lamp in the right headlight » page 185.
›
Remove the protective cap
E
» Fig. 194 on page 185 .
›
Turn the holder with the bulb in the direction of arrow
1
» Fig. 202 .
›
Remove the holder with the bulb in the direction of arrow
2
.
›
Remove the bulb from the holder in the direction of the arrow
3
.
›
Insert a new bulb into the connector so that the lug
A
on the connector
snaps into the groove on the bulb.
›
Insert the connector with the new bulb into the headlight in the opposite di-
rection to the arrow
2
.
›
Turn the connector with the new bulb in the opposite direction to the arrow
1
until it stops.
› Fit protective cap E
» Fig. 194 on page 185 .
After changing the lamp in the right headlamp, replace the holder of the wash
water container nozzle » page 185.
Replacing the turn signal switch bulb (halogen projector
headlights)
Fig. 203
Changing the bulb for the turn signal light
Read and observe
and on page 184 first.
To replace lamp, first remove the bracket of the wash water container nozzle
in the right headlight » page 185.
›
Remove the protective cap
E
» Fig. 194 on page 185 .
›
Remove the bulb holder with the bulb by jiggling it out in the direction of the
arrow
1
» Fig. 203 .
›
Grasp the lamp socket at the places marked by arrows.
›
Remove the faulty bulb from the holder in the direction of the arrow
2
.
›
Push a new bulb into the bulb holder up to the stop.
›
Replace the bulb holder in the headlamp with the bulb.
›
Fit protective cap
E
» Fig. 194 on page 185 .
After changing the lamp in the right headlamp, replace the holder of the wash
water container nozzle » page 185.
188Do-it-yourself

Downloaded from www.Manualslib.com manuals search engine Replacing the bulb for the fog lightFig. 204
Removing the fog lamp / changing bulb for fog light switch
Read and observe
and on page 184 first.
Remove the protective grille and headlight
›
Insert the clamps for removing the full wheel covers into opening
A
» page 167 , Vehicle tool kit .
›
Loosen the protective grille by pulling the hook in the direction of arrow
1
» Fig. 204.
›
Grasp the guard with the hand and remove by pulling in the direction of the
arrow
2
.
›
Unscrew the screws
B
with the screwdriver from the tool kit » page 167.
›
Remove the headlight in the direction of arrow
3
.
Replacing the light bulb
›
Push in the latch on the connector in the direction of arrow
4
» Fig. 204 .
›
Remove the key in the direction of the arrow
5
.
›
Turn the socket with the bulb to the stop in the direction of the arrow
6
.
›
Remove the socket with the bulb in the direction of arrow
7
.
›
Insert the new bulb into the headlight and turn counter to the direction of
arrow
6
as far as the stop.
› Attach the connector.
Refit the headlight and grille›
Replace the fog light by inserting it in the opposite direction of the arrow
3
» Fig. 204 and tightening.
›
Insert the protective grille and carefully press it in.
The protective grille must engage firmly.
Changing the licence plate light bulb
Fig. 205
Remove the licence plate light
Fig. 206
Remove the cover / replace the bulb
Read and observe
and on page 184 first.
›
Open the tailgate.
›
Push in the lamp in the direction of the arrow
1
» Fig. 205 .
The lamp comes loose.
›
Swivel out the lamp in the direction of the arrow
2
and remove it.
›
Remove the cap of the lamp in range
A
and in the direction of arrow
3
» Fig. 206 . 
189Fuses and light bulbs

Downloaded from www.Manualslib.com manuals search engine ›Remove the cap of the light in the direction of arrow 4.›Remove the faulty bulb from the holder in the direction of the arrow 5.›
Insert a new bulb into the holder.
›
Clip in the cap of the lamp counter to the direction of arrow
4
.
›
Reinsert the lamp in the opposite direction to the arrow
1
.
›
Push on the light until the spring clicks into place.
Check that the light is securely inserted.
›
Shut the boot lid.
Rear Light
Fig. 207
Remove light / pull out connector
Read and observe
and on page 184 first.
Removing
›
Open the tailgate.
›
Unscrew the screws
A
with the screwdriver from the tool kit » page 167.
›
Into the opening
B
insert the clamps for removing the full wheel trims, di-
rected with the eyelet downward (in the right light with the eyelet upward).
›
Grasp the light with the palm of the hand and remove carefully in the direc-
tion of arrow
1
» Fig. 207 from the pin
D
.
›
Press the latch
C
on the holder in the direction of the arrow
2
.
›
Press the latch in the direction of arrow
3
and pull out the holder in the di-
rection of arrow
4
.
Fitting
›
Insert the bulb holder into the lamp.
›
Tighten the lock in the opposite direction to the arrow
2
» Fig. 207 .
›
Insert the lamp with the holes
B
» Fig. 208 on page 190 onto the pins
D
» Fig. 207 in the body.
›Carefully press the light into the pins on the bodywork
» .
Ensure that the wiring harness does not become pinched between the body
and the lamp.›
Screw the light into place.
CAUTION
■ Ensure that the wiring harness does not become pinched between the body
and the lamp when it is being refitted – risk of damage to the electrical instal-
lation and risk of water ingress.■
If you are not sure whether the wiring harness has become pinched, we rec-
ommend that you have the light connection checked by a specialist garage.
■
Ensure that the vehicle paintwork and the tail lamp are not damaged when
removing and installing the tail lamp.
Replacing bulbs in rear light
Fig. 208
Outer part of the lamp / removing the bulb / lamp holder
Read and observe
and on page 184 first.
Changing the bulb in the outer part of the lamp
›
Turn the holder with the bulb
A
in the direction of the arrow
1
» Fig. 208 .
›
Remove the socket with the bulb from the lamp housing in the direction of
arrow
2
.
›
Jiggle the bulb to remove.
›
Insert a new bulb into the socket.
›
Reinsert the holder with the bulb into the lamp housing and turn in the op-
posite direction of the arrow
1
to the stop.
Changing the bulb in the inner part of the lamp
›
Turn the holders with the bulbs
A
in the direction of the arrow
1
» Fig. 208 .
190Do-it-yourself

Downloaded from www.Manualslib.com manuals search engine ›Remove the holders with the bulbs from the lamp housing in the direction of
the arrow 2.›
Release the bulb holder in the areas identified by arrows » Fig. 208.
›
Remove the holder from the lamp.
›
Turn the respective light bulb counter-clockwise to the stop and remove it
from the bulb holder.
›
Insert a new bulb into the holder and turn in a clockwise direction to the
stop.
›
Insert the bulb holder in the light.
The lamp holder must engage firmly.
›
Reinsert the holders with the bulbs into the lamp housing and turn in the op-
posite direction of the arrow
1
.
191Fuses and light bulbs

Downloaded from www.Manualslib.com manuals search engine Technical data
Technical data
Vehicle data
Introduction
This chapter contains information on the following subjects:
Vehicle characteristics
192
Operating weight and payload
193
measurement of fuel consumption and CO 2 emissions according to ECE
Regulations and EU Directives
193
Dimensions
194
Departure angle
195
Vehicle-specific details per engine type
196
The details given in the vehicle's technical documentation always take prece-
dence over the details in the Owner's Manual.
The listed performance values were determined without performance-reduc- ing equipment, e.g. air conditioning system.
Vehicle characteristics
Fig. 209
Vehicle data sticker/type plate
Vehicle data sticker
The vehicle data sticker » Fig. 209 -  is located on the base of the luggage
compartment and is also stuck inside the service schedule.
The vehicle data sticker contains the following data. Vehicle identification number (VIN)
Vehicle type
Gearbox code / paint number / interior equipment / engine output / engine code
Partial vehicle description
Approved tyre diameter in inches 1)
The approved tyres and rim sizes for your vehicle are listed in the vehicle's
technical documentation (the so called COC document) and this also states the
declaration of conformity.
Type plate
The type plate » Fig. 209 -
 is located at the bottom of the B-pillar on the
right-hand driver's side.
The type plate contains the following data. Manufacturer
Vehicle identification number (VIN)
Maximum permissible gross weight
Maximum permissible towed weight (towing vehicle and trailer)
Maximum permissible front axle load
Maximum permissible rear axle load
Vehicle identification number (VIN)
The vehicle identification number - VIN (vehicle body number) is stamped on
the right hand suspension strut dome in the engine compartment. This num-
ber is also located on a sign on the lower left hand edge below the windscreen
(together with a VIN bar code), together with a nameplate.
The VIN number can also be displayed in the Infotainment » Operating instruc-
tions Infotainment , chapter CAR - vehicle settings .
Engine number
The engine number (three-digit code letter and serial number) is stamped onto
the engine block. 12345678910111)
Only valid for some countries.
192Technical data

Downloaded from www.Manualslib.com manuals search engine Supplementary Information (applies to Russia)
The full type approval number of the means of transport is indicated in the
registration documents, field 17.WARNINGDo not exceed the specified maximum permissible weights – risk of an acci-
dent and damage.
Operating weight and payload
Operating weight
This value represents the minimum operating weight without additional
weight-increasing equipment such as air conditioning system, spare wheel, or
trailer hitch.
The specified operating weight is for orientation purposes only.
The operating weight also contains the weight of the driver (75 kg), the weight
of the operating fluids, the tool kit, and a fuel tank filled to 90 % capacity.
Operating weight of the vehicle » page 196, Vehicle-specific details per en-
gine type .
Payload
It is possible to calculate the approximate loading capacity from the difference
between the permissible total weight and the operating weight.
The payload consists of the following weights.
› The weight of the passengers.
› The weight of all items of luggage and other loads.
› The weight of the roof, including the roof rack system.
› The weight of the equipment that is excluded from the operating weight.
› Trailer drawbar load when towing a trailer (max. 50 kg).
Note
If required, you can find out the precise weight of your vehicle by contacting a
specialist garage.
measurement of fuel consumption and CO 2 emissions according to
ECE Regulations and EU Directives
The data on fuel consumption and CO 2 emissions were not available at the
time of going to press.
The data on fuel consumption and CO 2 emissions are given on the ŠKODA
websites or in the sales and technical vehicle documentation.
The measurement of the intra-urban cycle begins with a cold start of the en-
gine. Urban driving is then simulated.
In the extra-urban driving cycle, the vehicle is accelerated and decelerated in
all gears, corresponding to daily routine driving conditions. The driving speed
varies between 0 and 120 km/h.
The calculation of the combined fuel consumption considers a weighting of
about 37 % for the intra-urban cycle and 63 % for the extra-urban cycle.
Note
■ The fuel consumption and emission levels given on the Škoda websites or in
the commercial and technical vehicle documentation have been established in
accordance with rules and under conditions that are set out by legal or techni-
cal rules for the determination of operational and technical data of motor vehi-
cles.■
Depending on the extent of the equipment, the driving style, traffic condi-
tions, weather influences and vehicle condition, consumption values can in
practice result in fuel economy figures in the use of the vehicle that differ from
the fuel consumption values listed on the ŠKODA websites or in the commer-
cial and technical vehicle documentation.
193Technical data

Downloaded from www.Manualslib.com manuals search engine DimensionsFig. 210
Principle sketch: Vehicle dimensions
Vehicle dimensions by operating weight without driver (in mm)
» Fig. 210SpecificationFabiaFabia CombiA
Height
Basic dimension14671467Vehicles with off-road package14821482Vehicles with SPORT package14521452BFront trackBasic dimension14631463Vehicles with the 1.2 l/81 kW TSI and 1.4 l/77 kW TDI engine14571457CWidth17321732DRear trackBasic dimension14571457Vehicles with the 1.2 l/81 kW TSI and 1.4 l/77 kW TDI engine14511451EWidth including exterior mirrors19581958F
Clearance
Basic dimension133135Vehicles with off-road package141143Vehicles with SPORT package118120GWheelbase24702470HLength39924257194Technical data

Downloaded from www.Manualslib.com manuals search engine Departure angleFig. 211
Principle sketch: Departure an-
gle
Angle » Fig. 211
Overhang angle, front
Overhang angle, rear
Departure angle
The values shown indicate the maximum incline of an embankment, up which
the vehicle can drive at a slow speed without collision of the bumper or under-
body.
The values listed correspond to the maximum axle load, front or back.
Overhang angle (°)
» Fig. 211FabiaFabia CombiA14.614.6B17.613.1AB195Technical data

Downloaded from www.Manualslib.com manuals search engine Vehicle-specific details per engine typeThe values specified have been determined in accordance with rules and under conditions set out by legal or technical requirements for determining operational
and technical data for motor vehicles.
1.0 l/44 kW MPI engine
Output (kW per rpm)Maximum torque (Nm per rpm)Number of cylinders/displacement (cm 3
)44/5000-600095/3000-43003/999Performance and weightsFabia MG5Top speed (km/h)160Acceleration 0 - 100 km/h (s)15.7Operating weight (kg)1055Permissible trailer weight braked (kg)Gradients of up to 12 %800Gradients of up to 8 %1000Permissible trailer weight unbraked (kg)520
1.0 l/55 kW MPI engine
Output (kW per rpm)Max. torque (Nm per rpm)Number of cylinders/displacement (cm 3
)55/620095/3000-43003/999Performance and weightsFabia MG5 EU6Fabia MG5 EU4Fabia Estate
MG5 EU6Fabia Estate MG5 EU4Top speed (km/h)172172175175Acceleration 0 - 100 km/h (s)14.714.714.914.9Operating weight (kg)1055105010791074Permissible trailer weight braked (kg)Gradients of up to 12 %800800800800Gradients of up to 8 %1000100010001000Permissible trailer weight unbraked (kg)520520530530 196Technical data

Downloaded from www.Manualslib.com manuals search engine 1.2 ltr./66 kW TSI engineOutput (kW at rpm)Maximum torque (Nm at rpm)Number of cylinders / displacement (cm3
)66/4400-5400160/1400-35004/1197Performance and weightsFabia MG5Fabia Combi MG5Top speed (km/h)182185Acceleration 0 - 100 km/h (s)10.911.0Operating weight (kg)11091133Permissible trailer weight braked (kg)Gradients of up to 12 %10001000Gradients of up to 8 %11001100Permissible trailer weight unbraked (kg)550560
1.2 ltr. / 81 kW TSI engine
Output (kW per rpm)Maximum torque (Nm per rpm)Number of cylinders/displacement (cm 3
)81/4600-5600175/1400-40004/1197Performance and weightsFabia MG6Fabia DSG7Fabia Combi
MG6Fabia CombiDSG7Top speed (km/h)196196199199Acceleration 0 - 100 km/h (s)9.49.49.69.6Operating weight (kg)1129115411531178Permissible trailer weight braked (kg)Gradients of up to 12 %1100110011001100Gradients of up to 8 %1100110011001100Permissible trailer weight unbraked (kg)560570570580 197Technical data