SKODA SUPERB 2009 2.G / (B6/3T) Owner's Manual

Fuses and light bulbs
260
Fuse assignment in the dash panelCertain electrical components are only st
andard on certain vehicle model versions
or only suppliable as optional
equipment for certain models.
No.
Power consumer
Amperes
1
Diagnostic socket, engine control unit, fuel pump relay, fuel pump control unit
7,5
2
Control unit for ABS, ESP, switch for tyre air pressure control, brake sensor
5
3
Switch and control unit for airbag
5
4
WIV, parking light, dimming mirrors, pressure sensor, telephone preinstallation
5
5
Control unit for headlamp beam adjustment and head- light swivel, control unit for parking aid, control unit for park assist
5
6
Instrument cluster, control
unit for electromechanical
power steering, Haldex, selector lever lock, power sup- ply for data bus
5
Fig. 232 Schematic repre- sentation of the fuse carrier in the dash panel
7
Valve heating, air mass meter
10
8
Control unit for trailer detection
5
9
Relay for auxiliary heating
5
10
Adaptive left main headlight
10
11
Adaptive right main headlight
10
12
Central locking of the front doors
10
13
Diagnostic socket, light switch, rain sensor, clock
7,5
14
Central locking system and bonnet lid
15
15
Central control unit - interior lights
7,5
16
Air conditioning system
7,5
17
Central locking system of the rear doors
10
18
Not assigned
19
Not assigned
20
Not assigned
21
Not assigned
22
Air blower for Climatronic
40
23
Front power window
30
24
Selector lever lock
5
25
Rear wind
ow heater
relay for auxiliary heating and ventilation
2530
26
Power socket in the luggage compartment
25
27
Fuel pump relay, Fuel pump relay, control unit for fuel pump, injection valves
1520
28
Not assigned
29
Preparation for the aftermarket radio
5
No.
Power consumer
Amperes
s2dk.1.book Page 260 Wednesday, April 8, 2009 12:23 PM

Fuses and light bulbs
261
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Electrically adjustable seats are protected by
automatic circuit breakers
, which
switch on again automatically after a few seconds after the overload has been eliminated.
BulbsChanging bulbsThe relevant lamp must always be switch
ed off before a light bulb is replaced.
Defect light bulbs should only be replaced
with light bulbs of the same type. The
designation is located on the light socket or the glass bulb. Changing certain bulbs is not something wh
ich you can do yourself, but requires to
be done by a specialist. Other parts of the vehicle must be removed in order to change the light bulbs. This applies, in
particular, to bulbs which can only be
reached from the engine compartment. We therefore recommend that you have an
y bulbs changed by an authorised Škoda
Service Partner or, in exceptional cases, by
calling on other professional assistance.
Please note that the engine co
mpartment is a hazardous area
⇒page 223,
“Working in the engine compartment”. We recommend that you always have a sm
all box of replacement bulbs in your
vehicle. You can obtain replacement bulbs from Škoda original accessories or from a specialist garage
18).
The set of light bulbs can be stowed in the locable box in the spare wheel.Fitted with a xenon headlightChange of light bulbs on Xenon lights (low beam lights, parking lights and main beam lights) should be undertaken by a specialist garage. Overview of bulbs
30
Not assigned
31
Not assigned
32
Rear power window
30
33
Electric sliding/tilting roof
25
34
Alarm, spare horn
5
35
front and rear lighter
25
36
Headlight cleaning system
20
37
Front seat heating
20
38
Heated rear seats
20
39
Not assigned
40
Fan air-conditioning system,
relay for auxiliary heating
and ventilation
40
41
Not assigned
42
Light switch
5
43
Control unit for trailer detection
15
44
Control unit for trailer detection
20
45
Control unit for trailer detection
15
46
Heatable washing nozzles, relay for auxiliary heating and ventilation, switch for seat heating
5
47
Not assigned
48
Not assigned
49
Not assigned
No.
Power consumer
Amperes
18)The small box with replacement bulbs is part of the basic equipping of the vehicle in some countries.
s2dk.1.book Page 261 Wednesday, April 8, 2009 12:23 PM

Fuses and light bulbs
262
WARNING
•
Bulbs H7 and H3 are pressurised and
may burst when changing the bulb
- risk of injury!•
It is recommended to wear gloves an
d eye protection when changing a
light bulb.•
Gas discharge bulbs* (xenon bulbs) op
erate with a high voltage, profes-
sional knowledge is requ
ired - danger to life!
Caution
Do not take hold of the glass bulb with naked fingers (even the smallest amount of dirt reduces the working life of the light bu
lb). Use a clean cloth, serviette or some-
thing similar.
Note
This Owner's Manual only describes the replacement of bulbs where it is assumed that no major complications will arise. Othe
r light bulbs should be changed by your
specialist garage.Front headlight
Front headlight
Halogen headlight
Xenon headlight
Low beam
H7
D1S
Main beam light
H3
D1S, H3
Parking lights
W5W
Turn signals
PY 24W
Fog lights
H8
Rear light unit
Bulb
Reversing light
W16W
Turn signals
PY21W
Light bulb for the brake lights and tail lights
W16W
Parking lights
W5W
Fog lights
P21W
Others
Bulb
Licence plate light
C5W
front interior lighting
W5W
3. Brake light
LED
Rear interior lighting
W5W
Storage compartment light - front pas- senger side
C3W
Footwell light
W5W
Luggage compartment light
W5W
Door warning light
W5W
Lighting for vanity mirror
C5W
Entry light
W5W
Fig. 233 Front headlight: Installing the light bulbs
s2dk.1.book Page 262 Wednesday, April 8, 2009 12:23 PM

Fuses and light bulbs
263
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Positions of the light bulbs in the front headlight
⇒page 262, fig. 233
.
- parking lights and main beam lights - low beam lights - Turn signal light (at the front)Parking lights and main beam lightsRemoving the light bulb for the parking light – Switch the ignition and all lights off. – Open the bonnet. – Remove the protective cap
⇒
page 262, fig. 233
.
– Remove the socket
⇒
fig. 234
.
– Take the faulty bulb out of the fixture and insert a new one. Removing the light bulb for the main beam light – Switch the ignition and all lights off. – Open the bonnet.– Remove the protective cap
⇒
page 262, fig. 233
.
– Press the sprung wire clamps
⇒
fig. 234
together and hang them
to the side.
– Remove the socket
⇒
fig. 234
.
– Take the faulty bulb out of the fixture and insert a new one.Installation takes place in the reverse order.
Note
We recommend that you have the headlight setting checked by a Skoda Service Partner after replacing the light bulb.Low beam light– Switch the ignition and all lights off. – Open the bonnet. – Remove the protective cap
⇒
page 262, fig. 233
.
– Turn the connector with the light bulb up to the stop towards the left
and remove
⇒
fig. 235
.
AAABAC
Fig. 234 Removing the bulbs for the parking and main beam light
AA
AA
AA
AB
AC
Fig. 235 Removing the light bulb for the low beam light
AB
s2dk.1.book Page 263 Wednesday, April 8, 2009 12:23 PM

Fuses and light bulbs
264
– Replace the lamp, insert the connector with the new lamp and turn to
the right up to the stop.
– Insert the protective cap.
Note
We recommend that you have the headli
ght setting checked by a Skoda Service
Partner after replacing the light bulb.Fog lights– Switch the ignition and all lights off.
– Grasp the grille at the point marked with the arrow and take it out
⇒
fig. 236
.
– Guide your hand into the opening
in which the grille was located and
press the spring bolt
⇒
fig. 237
.
– Take out the fog light.– Turn the connector with the light bulb
up to the stop towards the left
and remove.
– Replace the lamp, insert the connector with the new lamp and turn to
the right up to the stop.
– For the installation, first of all insert the fog light with the interlock to
the side far away from the marking of the vehicle.
– Press into place the headlight onto the side facing the marking. – First of all put the grille with the latch in place on the side opposite the
marking.
– Press into place the protective grille onto the side facing the
marking.
Rear light unit
Fig. 236 Front bumper: Protective grilleFig. 237 Removing the front fog light
Fig. 238 Remove the outer part of the rear light unit
s2dk.1.book Page 264 Wednesday, April 8, 2009 12:23 PM

Fuses and light bulbs
265
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Remove and install the outer part of the rear light unit – Switch the ignition and all lights off. – Open the boot lid/luggage compartment door. – Take out the plug
⇒
page 264, fig. 238
and unscrew the rear light unit
using a torx wrench
19).
– Carefully take out the light. Do not pull the grommet with the cables
out of the body.
– To re-insert the rear light unit, firs
t of all guide it with the support
⇒
fig. 240
towards the front onto a bolt on the bodywork.
– Carefully press the rear light unit into the bodywork.– Screw the rear light unit tight and press in the plugs
⇒
page 264,
fig. 238
.
Remove and install the inner part of the rear light unit – Switch the ignition and all lights off. – Open the boot lid/luggage compartment door.
– Take off the cover of the rear light unit on the inner side of the bonnet
lid
⇒
fig. 239
.
– Press the spring bolt
⇒
fig. 239
and take the lamp holder out of the
housing of the rear light unit.
– To re-insert the lamp holder, guide it into the housing of the rear light
unit.
–Press onto the spring bolt
until it is heard to lock.
– Guide the cover of the rear light uni
t into the inner side of the bonnet
lid. Caution
When removing and installing the rear
light unit make sure not to damage the
paintwork of the vehicle and the rear light unit.Changing light bulbs in the rear light unit
19)The torx wrench is located in a ve
hicle toolkit box on the spare wheel.
Fig. 239 Remove the inner part of the rear light unit
AA
Fig. 240 Outer part of the rear light unit: Lamps
s2dk.1.book Page 265 Wednesday, April 8, 2009 12:23 PM

Fuses and light bulbs
266
Change bulbs in the outer part of the rear light unit – To change a bulb, turn its fixture to the left up to the top and take it out. – Change the bulb, insert again the fixture with the bulb into the housing
and turn it to the right up to the stop.
Change bulbs in the inner part of the rear light unit – To change a bulb of the reversing light
⇒
fig. 241
, pull the defective
bulb out of the fixture and insert a new one.
– To change the bulb of the rear fog light
⇒
fig. 241
, turn the defec-
tive bulb to the left up to the stop and take it out.
– Press a new light bulb into the socket and turn the light bulb to the
right as far as the stop.
Fitting position of the bulbs in the outer rear light unit
⇒page 265, fig. 240
.
1 - Turn signal light2 - Parking lights / Brake light3 - Parking lights Fitting position of the bulbs in the inner rear light unit
⇒fig. 241
.
1 - Reversing lights 2 - Rear fog lightLicence plate light– Unscrew the glass cover of the light
⇒
fig. 242
.
– Take the faulty bulb out of the holder and insert a new one. – Replace the the glass cover of the light and press it down to the stop -
ensure that the glass cover is correctly installed.
– Screw the glass cover tight.
Fig. 241 Inner part of the rear light unit: Lamps
A1A2
Fig. 242 Rear bumper: Licence plate light
s2dk.1.book Page 266 Wednesday, April 8, 2009 12:23 PM

Technical Data
267
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Technical DataTechnical DataGeneral informationThe details given in the official vehicle
registration document
s always take prece-
dence over the details in th
e Owner's Manual. Please refe
r to the official vehicle
registration documents or consult an auth
orised Škoda Service Partner concerning
the engine with which yo
ur vehicle is equipped.
Used abbreviations
PerformancesThe listed performance values were de
termined without pe
rformance-reducing
equipment, e.g. air conditioning system.WeightThe loading capacity is reduced in line with the range of the special equipment. The unloaden weight contains a fu
el tank topped up to 90%.
Abbreviation
Importance
kW
Kilowatt, measuring unit for the engine output
rpm
Engine revolutions per minute
Nm
Newton meter, measuring unit for the engine torque
CO2 in g/km
discharged quantity of carbon dioxide in grams per driven kilom- eter
RON
Research octane number, measur
ing unit for the knocking resist-
ance of petrol
FSI
Petrol engine with a direct fuel injection system
TSI
Petrol engine with a turbocharger and a direct fuel injection sys- tem
TDI PD
Diesel engine with turbocharger
and injection system unit injec-
tor
TDI CR
Diesel engine with turbocharger
and injection system Common
Rail
DPF
Diesel particle filter
M5
5-speed manual gearbox
M6
6-speed manual gearbox
DQ6
6-speed automatic gearbox DSG
DQ7
7-speed automatic gearbox DSG
Abbreviation
Importance
s2dk.1.book Page 267 Wednesday, April 8, 2009 12:23 PM

Technical Data
268
Identification detailsVehicle data sticker The vehicle data sticker
⇒fig. 243
is located on the floor of the luggage compart-
ment and is also stated in the Service schedule. The vehicle data sticker co
ntains the following data:
Vehicle identification number (VIN). Vehicle type.Gearbox code, paint number, interior
equipment number, engine output,
engine code. Partial description of the vehicle.7GG, 7MB, 7MG - vehicles with DPF
⇒page 200.
Vehicle identification number (VIN) The vehicle identification num
ber - VIN (vehicle body number) is stamped into the
engine compartment on the right hand shoc
k absorber dome. This number is also
located on a sign on the lower left hand
edge below the windscreen (together with
a VIN bar code).
Engine number The engine number is stam
ped into the engine block.
Type plate (production plate) It is located on the left
middle pillar of the body.
Homologation sign The homologation sign is located on the lock carrier. Vehicles for certain countries do not have an homologation sign. Sticker on inside of fuel filler flap The stickers are affixed to the inside of the fuel filler flap. They contain the following data:•
The prescribed types of fuel,
•
Tyre s iz e ,
•
Tyre pressure.
Fuel consumption according to the regulations (99/100/EU)Depending on the range of the special equipment, style of driving, traffic situation, weather influences and vehi
cle condition, the consumpt
ion values which in prac-
tice result when using the vehicle ca
n deviate from the indicated values.
Urban traffic The consumption measurement in urban traf
fic begins with starting of the cold
engine. Afterwards the normal
urban traffic is simulated.
Non-urban traffic For the consumption measurement in non-ur
ban traffic the vehicle, as in daily
motoring, is accelerated and braked several times in all gears. The vehicle speed changes within the range from 0 to 120 km/h.
Fig. 243 Vehicle data sticker
A1A2A3A4A5s2dk.1.book Page 268 Wednesday, April 8, 2009 12:23 PM

Technical Data
269
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Combined traffic The consumption value in the combined traf
fic consists of 37%
from the value for
the urban traffic and of 63% from
the value for the non-urban traffic.
Note
•
Please note that the information stated in the
official vehicle registration
documents
always takes priority.
DimensionsDimensions (mm)Length
4838/4849
a)
a)The value corresponds to the status
with visual appearance package.
Width
1817
Width including
exterior mirror
2009
Height
1462/1482
b)/1447
c)
b)The value corresponds to the status with rough road package.c)The value corresponds to the status with sport chassis.Clearance
139/158
b)/123
c)
Wheel base
2761
Tr a c k g a u g e f r o n t / r e a r
1545/1518 1537/1510
d)
1545/1517
e)
d)Valid for vehicles with 3.6°ltr./191°kW FSI engine.e)Superb GreenLine.
s2dk.1.book Page 269 Wednesday, April 8, 2009 12:23 PM