SKODA YETI 2009 1.G / 5L Owner's Manual
Manufacturer: SKODA, Model Year: 2009, Model line: YETI, Model: SKODA YETI 2009 1.G / 5LPages: 271, PDF Size: 16.24 MB
Page 121 of 271
Starting-off and Driving
120
Changing a stored speed You can also change the speed of the vehicle without depressing the accelerator.Fa s t e r–You can
increase
the stored speed without depressing the accelerator, by pressing
the rocker button
⇒fig. 122
in the
RES
position.
– The speed of the vehicle will increase co
ntinuously if you hold the rocker button
pressed in the
RES
position. Once the vehicle has reached the desired speed,
release the rocker button. The set speed is then stored in the memory.
Slower–You can
decrease
the stored speed by pressing the rocker button in the
SET
position.
– Holding down the rocker button pressed in the
SET
position will cause the speed
of the vehicle to reduce continuously.
Once the vehicle has
reached the desired
speed, release the rocker button. The set speed is then stored in the memory.
– If you release the rocker button when the vehicle is travelling at a speed of less than
30 km/h, the speed is not stored, the memory is erased. It is then necessary to again store the speed with the rocker button in the position
SET
after an increase in
speed of the vehicle to more than 30 km/hour.
Switching off the cruise control system temporarily–You can
switch off
the cruise control system temporarily by
depressing
the brake
pedal or clutch pedal, on
models with automatic gearbox and only with brake
pedal.
– You can switch off temporarily the cruise control system, if you press the switch
in the middle position.
The set speed remains stored in the memory. The
Resumption
of the stored speed is achieved by releasing the brake or clutch
pedal, on vehicles fitted wi
th automatic gearbox only af
ter releasing the brake pedal
and after shortly pressing the rocker button
⇒page 119, fig. 122
into the position
RES
.WARNING
First ensure that it is not too high for the traffic conditions which exist at that moment before resuming the stored speed.Switching off the cruise control system completely– Press the switch
⇒page 119, fig. 122
to the right into position
OFF
.
AB
AB
AB
AA
AB
AA
sgg.6.book Page 120 Thursday, September 24, 2009 2:32 PM
Page 122 of 271
Automatic gearbox DSG*
121
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Automatic gearbox DSG*Automatic gearbox DSG*IntroductionYour car is equipped with an automatic
gearbox DSG. The abbreviation DSG means
Direct shift gearbox (Direct shift gearbox). Two independent clutches are needed for the power transmission between the engine and the gearbox. These replace the torque converter of the conventional automatic gearbox. Their shifting is matched in such a
way that there are no jerks when shifting
the gear and the power transmission of the engine to the front wheels is not interrupted.Information for driving with the automatic gearbox DSG Shifting up and down through the gears is performed automatically.You can also, however, switch the gearbox over into the
Tiptronic mode
. This mode
makes it possible for you to also shift gears manually
⇒page 124.
Starting-off and Driving– Depress the brake pedal fully and keep it depressed. – Press the Shiftlock button (button in ha
ndle of the selector lever), move the
selector lever into the
desired position, e.g.
D ⇒page 122, and then release the
Shiftlock button.
– Release the brake pedal and depress the accelerator
⇒
.
Stopping for a short time– The selector lever position
N does not have to be selected when stopping just for
a short time, such as at a cross roads. It
is sufficient to hold
the vehicle stationary
using the foot brake. The engine can, however, be allowed just to idle.
Parking– Depress the brake pedal and hold it depressed.
– Apply the handbrake firmly. – Press and Shiftlock button in the selector lever, move the selector lever to
P and
then release the Shiftlock button.
The engine can only be
started
when the selector lever is in position
P or N
⇒ page 110. At temperatures below -10 °C the engine can only be started in the selector lever position
P.
It is sufficient to engage selector lever position
P when parking on a flat surface. When
parking on a slope you should first apply
the handbrake firmly and then move the
selector lever into position
P. This is to ensure that there is no excessive pressure acting
on the lock mechanism and that it is easier to subsequently move the selector lever out of position
P.
If the selector lever position
N is selected by accident while driving it is first necessary
to release pressure on the accelerator pedal and wait for idling speed of the engine to be reached before engaging a driv
e position in the selector lever.
WARNING
•
Do not depress the accelerator when changing the position of the selector
lever if the car is stationary and the engine is running - risk of accident!•
Never move the selector lever into position R or P when driving - risk of an
accident!•
If you are stopping at a hill (downhill section), never try to hold the car
stationary with the gear engaged by mean
s of the “accelerator”, this means by
letting the clutch slip. This can lead to ov
erheating of the clutch
. If there is a risk
of overheating of the clutch due to overlo
ad, the clutch is op
ened automatically
and the vehicle rolls backward - risk of accident!•
If yo u m us t s to p a t a sl ope , d e pre s s a nd ho ld t he b ra ke pe d a l , s o t ha t y ou c a n
prevent the vehicle from rolling back.
sgg.6.book Page 121 Thursday, September 24, 2009 2:32 PM
Page 123 of 271
Automatic gearbox DSG*
122
Caution
•
The double clutch on the automatic gear
box DSG is equipped
with an overload
protection. If you make use of
the uphill function on a vehicle which is stationary or
driving slowly uphill, it will result in an
increase of thermal stress of the clutches.
•
In the event that they overheat, the warning light
and a warning text
⇒page 38
appear in the information display*. In such a case bring the vehicle to a stop, switch off the engine and wait until the warning light and the warning go out - risk of gearbox damage! You can continue the trip as soon as the warning light and the warning go out.Selector lever positionsFig. 123 Selector lever / informatio
n display: Selector lever positions
The current selector lever position is indica
ted in the information display of the instru-
ment cluster
⇒fig. 123
on the right. In the positions
D and
S the gear you have already
engaged will be additionally displayed on the display. - Parklock The driven wheels are locked me
chanically in this position.
The Parklock must only be engage
d when the vehicle is stationary
⇒
.
If you wish to move the selector lever into
or out of this position, you must press the
Shiftlock button in the handle of the select
or lever and at the same time depress the
brake pedal. If the battery is used, the selector lever cannot be moved out of the position
P.
- Reverse gear Reverse gear must only be engaged when
the vehicle is stationary and the engine
idling
⇒
.
The brake pedal must be depressed and at
the same time the Shiftlock must be
pressed, if you wish to obtain the selector lever positions
R, P or N.
When the ignition is switched on an
d the selector lever is in position
R, the reverse
lights will come on. - Neutral The transmission is in Neutral in this position. The brake pedal must be depressed (if the le
ver is in its position for longer than 2
seconds) in order to move the se
lector lever out of the position
N into the position
D
or R, with the ignition switched on, on a vehicl
e travelling at less than 5 km/hour or on
a stationary vehicle. - Position for driving forward When the selector lever is in this position, the forward gears are shifted up and down automatically in line with engine load, vehicle speed and the dynamic shift programme. You must depress the brake pedal if you wish to move into position
D from
N when the
vehicle is travelling at less th
an 5 km/hour or is stationary
⇒
.
In certain circumstances (e.g.
when driving in mountainous regions or when towing a
trailer) it may be beneficial to
select the manual shift programme
⇒page 124 for a
short time in order to adapt the gearbox
ratios manually to the driving situations.
- Position for sporty style of driving Shifting up later into a higher gear makes it
possible to fully exploit the power potential
of the engine. The gearbox also then shifts down at higher engine speeds as in the posi-tion
D.
The Shiftlock on the selector lever grip mu
st be pressed when moving the selector
lever out of the position
D into the position
S.
AP
ARANADAS
sgg.6.book Page 122 Thursday, September 24, 2009 2:32 PM
Page 124 of 271
Automatic gearbox DSG*
123
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
WARNING
•
Never move the selector lever into position R or P when driving - risk of an
accident!•
When the engine is running and the vehicle is stationary, it is necessary to
hold the car with the brake pedal in all the positions of the selector lever (except P and N) since the power transmission is never completely interrupted, also not when the engine is idling - the vehicle creeps. •
You must on no account unintentionally operate the throttle (e.g. by hand
from the engine compartment) if a driv
e position is engaged when the car is
stationary. The vehicle would otherwise
immediately start of
f - also when the
handbrake is firmly applied - risk of an accident!•
You must move the selector lever into position P and firmly apply the hand-
brake first before you or any other person opens the bonnet and starts working on the engine when it is running - risk of
accident! It is also essential to observe
all warnings
⇒page 204, “Working in the engine compartment”.
Selector lever lockAutomatic selector lever lock
With the ignition on, the selector lever is locked when it is in the positions
P and
N. You
must first of all depress the brake pedal in or
der to move the selector lever out of this
position. The warning light
⇒page 35 lights up in the instrument cluster as a
reminder for the driver when the selector lever is in position
P and
N.
A time delay element ensures that the selector lever is not blocked when rapidly switching over the position
N (e.g. from
R to D). This does, for example, allow one to
seesaw out a stuck vehicle. The selector lever lo
ck will click into place if the lever is in
the
N position for more than 2 seconds without the brake pedal being pressed.
The selector lever lock is only active if the
vehicle is stationary or
moving at speed of
less than 5 km/hour. The lock is swit
ched off automatically into position
N when the
car is travelling at a higher speed. Shiftlock button The Shiftlock button in the hand
le of selector lever prevents certain selector lever posi-
tions being engaged inadvertently. The selector lever lock is cancelled when you press the Shiftlock button.
Keylock - Ignition key withdrawal lock You can only withdraw the ignition key after
switching off the ignition if the selector
lever is in position
P. If the ignition key is withdrawn,
the selector lever is blocked in
position
P.
Kickdown function The kickdown function provides you with maximum acceleration power.Fully depressing the a
ccelerator pedal allows the kickdown function to be activated in
the desired driving program. This function has precedence over the driving programme and serves for maximum accelerati
on of the vehicle when exploiting the
maximum power potential of the engine wi
thout taking into account the current
selector lever position (
D, S or Tiptronic
). The gearbox shifts down to one or several
gears in line with the driving state and the vehicle accelerates. The gearbox does not shift up into the highest gear until the en
gine has reached its maximum revolutions for
this gear range.
WARNING
Please note that using the kickdown f
unction can result in the driven wheels
spinning on a smooth or slippery road surface - risk of skidding!Dynamic shift programmeThe automatic gearbox of your vehicle is
controlled electronically. Shifting up and
down through the gears is performed automatically on the basis of pre-defined driving programmes. Adopting a
moderate style of driving
will cause the gearbox to select the most
economical driving programme. Shifting up into a higher gear as soon as possible and shifting down as late as po
ssible will have a favourable effect on your fuel consump-
tion. Adopting a
sporty style of driving
with rapid movements of the accelerator pedal
combined with sharp acceleration and freque
nt changes in speed, exploiting the top
speed of the car or depressing the accele
rator pedal (kickdown function), will cause
sgg.6.book Page 123 Thursday, September 24, 2009 2:32 PM
Page 125 of 271
Automatic gearbox DSG*
124
the gearbox to switch over to this style of driving and shift down earlier with frequent changes in gears in comparison to the moderate style of driving. Selecting the most appropriate driving programme for the particular style of driving is a continuous process. Irrespective of this it is, however, possible to switch or shift down into a dynamic shift programme by depressi
ng the accelerator rapidly. The gearbox
shifts down into a lower gear matching th
e speed of the car and this allows you to
accelerate rapidly (e.g. when overtaking)
without having to depress the accelerator
pedal fully into the kickdown range. The
original programme will be reactivated to
match your particular styl
e of driving once the gearbox has shifted up again.
When driving in hilly regions, the gears
are selected to match uphill and downhill
sections. This avoids the gearbo
x frequently shifting up an
d down when negotiating an
uphill stretch. When driving downhill, it is possible to shift down into the Tiptronic position, in order to exploit the engine brake torque.Tiptronic The Tiptronic allows the driver
to also shift gears manually.
Fig. 124 Selector lever: manual shifting /
information display: Manual shifting of gears
The selector lever position you have engaged is indicated in the information display of the instrument cluster together with the engaged gear
⇒fig. 124
on the right.
Switching over to manual shifting– Push the selector lever to the right out of position
D. After switching over, the
current engaged gear is indicated in the display.
Shifting up gears– One-touch forward of the selector
lever (in the Tiptronic position)
⇒fig. 124
on
the left.
Shifting down gears– One-touch back of the selector
lever (in the Tiptronic position) .
It is possible to switch over to manual both
when the car is stationary and also when
driving. When you accelerate, the gearbox shifts up
automatically into the higher gear just
before the maximum
permissible engine speed is reached.
If you select a lower gear, the automatic gearbox does not shift down until there is no risk of the engine overrevving. If you operate the kickdown function, the gear
box shifts into a lower gear in line with
the vehicle speed and engine speed.Emergency programme An emergency programme exists in the event of a fault in the system.The gearbox operates in a corresponding emergency programme if there are func- tional faults in the gearbox electronics. This
is indicated by all of
the segments in the
display lighting up or going out. A functional fault can ha
ve the following effect:
•
The gearbox only shifts into certain gears.
•
The reverse gear
R cannot be used.
•
The manual shift programme (Tiptronic) is switched off in the emergency mode.
If the gearbox has switched over to
emergency mode, drive to the nearest
specialist garage in order to
have the fault rectified.
A+
A-
sgg.6.book Page 124 Thursday, September 24, 2009 2:32 PM
Page 126 of 271
Automatic gearbox DSG*
125
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Selector lever-emergency unlockingIn case of interruption of the power supply (e
.g. flat vehicle battery, defective fuse) or
defect of the selector lever lock, the select
or lever can no longer be shifted from the
position
P in the normal way and the vehicle ca
n no longer be moved. The selector
lever must be unlocked in case of emergency. – Apply the handbrake firmly.– Carefully pull up the front left and right cover. – Pull up rear cover. – Use the finger to press the yellow plastic part downwards
⇒fig. 125
.
– Simultaneously press the shiftlock button in
the handle of the selector lever in the
position
N10).
Tow-starting and towing vehicle Tow-starting a vehicle It is not possible to tow-start vehicles fitted with automatic gearbox
⇒page 230.
You can use jump-start cables connected to
the battery of another vehicle for starting
your car if the vehicle battery is flat
⇒page 229.
Towing a vehicle Please pay attention to the following information if it comes necessary to tow-in your car
⇒page 230.
10)If the selector lever is moved again into the position
P, it is once again blocked.Fig. 125 Selector lever-emergency unlocking
sgg.6.book Page 125 Thursday, September 24, 2009 2:32 PM
Page 127 of 271
Communication
126
CommunicationMultifunction steering wheel*Operate radio und navigation on the multifunction steering wheelThe driver can set the basic functions of th
e radio and navigation by simply operating
the buttons located on the steering wheel so
that he can concentrate on the traffic situ-
ation without being distracted as little as
possible by operating the radio and naviga-
tion
⇒fig. 126
.
This applies only if your vehicl
e has been installed with radio
11) or navigation system
at the factory. You can of course operate th
e radio and navigation at the appliance. You
will find a description in the operating instructions of your radio. When the headlights are switched on, the steering wheel pushbuttons are then also illuminated. The buttons apply for the respective operating mode of the current radio or navigation system. By pressing the buttons, you can carry out the following functions:11)Does not apply for Radio Blues.
Fig. 126 Multifunction steering wheel: control buttons
sgg.6.book Page 126 Thursday, September 24, 2009 2:32 PM
Page 128 of 271
Communication
127
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
sgg.6.book Page 127 Thursday, September 24, 2009 2:32 PM
Page 129 of 271
Communication
128
Button
Action
Radio, traffic information
CD
The CD changer / MP3
Navigation
press briefly
Switch off/on tone / activation and deactivation of the voice control
a)
press button for a long
period of time
switch off/on*
turn upwards
Increase volume
turn downwards
Decrease volume
press briefly
Changing to the next
stored radio station
Changing to the next stored traffic information
Interrupting the traffic report
Changing to the next title
press button for a
long time
Interruption of the traffic report
fast forward
press briefly
Changing to the previously stored radio station Changing to the previously stored traffic information
Interrupting the traffic report
Changing to the previous title
press button for a
long time
Interruption of the traffic report
fast rewind
Changing the audio source
press briefly
Calling up the main menu
press button for a long time
press briefly
Interruption of the traffic report
without function
press button for a long
period of time
turn upwards
Display of the station list
scroll upwards
Interruption of the traffic reports
Changing to the previous title
without function
turn downwards
Display of the station list
scroll downwards
Interruption of the traffic report
Changing to the next title
A1A1A1A1A2A2A3A3A4A5A5A6A6A6A6
sgg.6.book Page 128 Thursday, September 24, 2009 2:32 PM
Page 130 of 271
Communication
129
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Mobile phones and tw
o-way radio systems
The installation of a mobile phone and two-way radio system in a vehicle should be carried out by a specialist garage. Mobile phones send and receive radio wave
s during a conversation as well as in
standby mode. Radio waves can be harmful
to the human body if their frequency
exceeds certain limit values. Škoda Auto permits the operation of mobile
phones and two-way radio systems with
a professionally installed external aerial and a maximum transmission power of up to 10 watts. It is essential that you inform yourself at
a specialist garage about the possibilites to
assemble and operate systems
which have a power output of more than 10 W. They
will inform you which technical possibilit
ies exist for retrofitting mobile phones.
When using a mobille phone inside the vehicl
e, which is not inserted into the phone
adapter, and thus has no connection to the
external aerial, the electromagnetic radia-
tion can exceed the current limit value. We therefore recommend to operate a mobile phone in the vehicle only when it is conne
cted to an external aerial via the phone
adapter. This improves the quality of the connection. Operation of mobile phones or two-way ra
dio systems may interfere with functioning
of the electronic systems of your vehicle. The reasons for this may be:•
no external aerial,
•
external aerial incorrectly installed,
•
transmission power greater than 10 watts.
WARNING
•
If a mobile phone or a two-way radio
system is operated in the vehicle
without using a special exte
rnal aerial or an extern
al aerial which has been
incorrectly installed, this can increase the strength of the electromagnetic field in the interior of the vehicle.•
Please concentrate fully at
all times on your driving!
•
You must not install two-way radio systems, mobile phones or mounts on
the covers of the airbags or within the immediate deployment range of airbags. This might result in injuries to the
occupants in the event of an accident.
•
Never leave a mobile phone on a seat, on
the dash panel or in another area,
from which it can be thrown during a sudden braking manoeuver, an accident or a collision. In this case, the occupants of the vehicle might be injured.
Note
Observe the country-specific regulations for the use of mobile phones in vehicles.Universal telephone preinstallation GSM II*IntroductionThe telephone preinstallation GSM ll is a complete and built-in “handsfree-system”, it provides a voice operated convenience mode via the multifunction steering wheel* or the touchscreen of the radio*
or the navigation system*.
All communication between a telephone and
the handsfree-system of your vehicle
can only be established with the help of the Bluetooth
® technology. The adapter*
serves only for charging the telephone and fo
r transmitting the signal to the external
aerial of the vehicle. To ensure an optimum signal transmission, always leave the telephone with the adapter* in the telephone mount. A phone phonebook is part of the mobile ph
one preinstallation with voice control. In
the phone phonebook there are 1 500 free me
mory locations available. This phone
phonebook is independent of the a
ppliance used for the mobile phone.
If the system answers with the voice response “
Telephone is not ready
”, please check
the operating state of the telephone as follows:
a)Only valid for the navigation system Columbus.
WARNING (continued)
sgg.6.book Page 129 Thursday, September 24, 2009 2:32 PM