SKODA YETI 2009 1.G / 5L Owner's Manual

Starting-off and Driving
110
•
You should not switch on any major elec
trical components during the heating
period otherwise
the vehicle battery will
be drained unnecessarily.
- start engine Applies to all models: Position

To lock the steering
, with the ignition key withdrawn, turn the steering wheel until the
steering locking pin is heard to
engage. You should always lock the steering as a general
rule if you leave your vehicle. This acts as
a deterrent against possible theft of your
vehicle
⇒
.
Position

Move the steering wheel back and forward a little if the ignition key cannot, or cannot easily be turned into this position, in order to release the steering lock. Position

The engine is started in this position. At the same time, major electrical components are switched off for short periods. The igni
tion key moves back into position when
one releases the key. The ignition key must be turned back into
position each time before starting the
engine again. The starter repeat lock in th
e ignition lock prevents the starter being
engaged when the engine is r
unning and thus getting damaged.
Ignition key withdrawal lock (automatic gearbox) You can only withdraw the ignition key after switching off the ignition if the selector lever is in position
P.
WARNING
•
When driving, the ignition key must always be in the position (ignition
switched on) without the engine running. This position is indicated by the warning lights coming on. If this is not the case, it could result in unexpected locking of the steering wh
eel - risk of accident!
•
Only remove the ignition key from the ignition lock when the vehicle has
come to a standstill (by applying the handbrake or moving the selector lever into the position P). The
steering lock can engage imme
diately - risk of acci-
dent!
•
Always withdraw the ignition key if yo
u are going to leave the vehicle, even
for a short time. This is particularly important if children are left in the vehicle. The children might otherwise start the engi
ne or switch on el
ectrical equipment
(e.g. power windows) - risk of accident or injury!Starting the engineGeneral You can only start the engine only using an original ignition key.•
Place the gearshift lever into neutral (or
place the selector lever to the position
P or
N in the case of an automatic gearbox) and put on the handbrake firmly before starting the engine.•
The clutch pedal should be fully depressed when starting the engine - the starter
then only has to crank the engine.•
Let go of the key as soon as the engine starts otherwise there may be damage to
the starter. The engine running noises may louder at first be louder for a short time after starting the cold engine until oil pressure can be
built up in the hydraulic valve clearance
compensation. This is quite normal and is not an operating problem. If the engine does not start ... You can use the battery of anothe
r vehicle as a jump-start aid
⇒page 229.
It is only possible to tow-start vehicles fi
tted with a manual gearbox. The tow-starting
distance must not be more than 50 metres
⇒page 231.
WARNING
•
Never run the engine in non ventilated
or enclosed areas. The exhaust gases
of the engine contain besides the odorless and colourless carbon monoxide a poisonous gas - hazard! Carbon mono
xide can cause unconsciousness and
death.
A3
A1A2A3
A2
A1
A2
WARNING (continued)
sgg.6.book Page 110 Thursday, September 24, 2009 2:32 PM

Starting-off and Driving
111
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
•
Never leave your vehicle unattended with the engine running.Caution
•
The starter may only be operated (ignitio
n key position ), if the engine is not
running. If the starter is immedi
ately operated after switchin
g off the engine, the starter
or the engine can be damaged.•
Avoid high engine revolutions, full throttle and high engine loads as long as the
engine has not yet reached its normal oper
ating temperature - risk of damaging the
engine!•
Vehicles which are fitted with an exhaust gas catalytic converter should not be tow-
started over a distance of more than 50 metres.
For the sake of the environment
Never warm up the engine when the vehicle
is standing. Drive off right away. Through
this the engine reaches its operating temperature more rapidly and the pollutant emis- sions are lower.Petrol enginesThese engines are fitted with a starter system which selects the correct fuel-air mixture for every external air temperature.•
Do not operate accelerator before and when starting engine.
•
Interrupt the attempt at starting after 10
seconds if the engine does not start right
awayand wait for about 30 seconds before repeating the attempt.•
It is possible that the fuse on the electric
al fuel pump is defect if the engine still
does not start. Check the fuse and replace it if necessary
⇒page 233.
•
Contact the nearest specialist garage to obtain professional assistance.
It may be necessary, if the engine is
very hot
, to slightly depress the accelerator after
the engine has started.
Diesel enginesGlow plug system Diesel engines are equipped with a glow plug system, the preglow period being controlled automatically in
line with the coolant temperature and outside tempera-
ture. The preglow indicator light
 comes on after the ignition has been switched on.
You should not switch on any major electrical components during the heating period otherwise the vehicle battery
will be drained unnecessarily.
•
You should start the engine immediately after the glow plug warning light
 has
gone out.•
The glow plug warning light will come on for about one second if the engine is at a
normal operating temperature or if the outside temperature is above +5°C. This means that you can start the engine
right away
.
•
Interrupt the attempt at starting after 10 seconds if the engine does not start right
awayand wait for about 30 seconds before repeating the attempt.•
It is possible that the fuse
on the diesel preglow system is defect if the engine still
does not start. Check the fuse and replace it if necessary
⇒page 233.
•
Contact the nearest specialist garage to obtain professional assistance.
Starting the engine after
the fuel tank has run dry
It may take longer than normal to start the
engine after refuelling if the fuel tank has
run completely dry - up to one minute. This is
because the fuel system must first of all
be filled while the attempting to start the engine.Switching off the engine– The engine can be switched off by turnin
g the ignition key from position into
⇒ page 109, fig. 114
.
WARNING
•
Never switch off the engine before the ve
hicle is stationary - risk of accident!
WARNING (continued)
A3
A1
sgg.6.book Page 111 Thursday, September 24, 2009 2:32 PM

Starting-off and Driving
112
•
The brake booster only operates when
the engine is running. Greater phys-
ical effort for braking is required when en
gine is switched off. Because if you do
not stop as normal, this can cause an accident and severe injuries.
Caution
you should not switch the engine off right
away at the end of your journey after the
engine has been operated for a lengthy period
at high loads but should be allowed it
to run at idling speed for
about 2 minutes. This prevents any accumulation of heat
when the engine is switched off.
Note
•
The radiator fan may continue running fo
r a further 10 minutes or so after the
engine and the ignition have been switched
off. The coolant fan may, however, also
switch on again after some time if the co
olant temperature rises because of an accu-
mulation of heat in the engine or if the engine is warm and the engine compartment is additionally heated
by strong sunlight.
•
This is why particular care is required
when carrying out any work in the engine
compartment
⇒page 204, “Working in the engine compartment”.
Shifting (manual gearbox)
Shift into reverse only when the vehicle is
stationary. Depress the clutch pedal and hold
it fully depressed. Wait a mo
ment before engaging reverse gear in order to avoid any
shift noises. The reversing lights will come on once reverse gear is engaged, provided the ignition is on.
WARNING
Never engage the reverse gear when driving - risk of accident!
Note
•
One should not lay the hand on the shift lever while driving the vehicle. The pres-
sure of the hand will be transferred to the gearshift forks in the gearbox. This can, over a period of time, lead to earl
y wear of the gearshift forks.
•
Depress the clutch pedal fully when changi
ng gears, in order to avoid unnecessary
wear and damage.HandbrakeApplying the handbrake– Pull the handbrake lever up fully.
WARNING (continued)
Fig. 115 The shift pattern: 5-speed or 6- speed manual gearbox
Fig. 116 Centre console: Handbrake
sgg.6.book Page 112 Thursday, September 24, 2009 2:32 PM

Starting-off and Driving
113
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Releasing the handbrake– Pull the handbrake lever up slightly and
at the same time
press in the locking
button
⇒fig. 116
.
– Hold the button pressed and push the handbrake lever down fully
⇒
.
The handbrake warning light
 lights up when the handbrak
e is applied, provided the
ignition is on. A warning signal sounds and the following text
appears in the display* if you have inad-
vertently driven off with the handbrake applied:
Handbrake on
The handbrake warning is acti
vated if you drive at a speed of more than 6 km/h for
more than 3 seconds.
WARNING
•
Please note that the handbrake must be fully released. A handbrake which
is only partially released can result in the rear brakes overheating which will have a negative effect on the operation of
the brake system - risk of accident! In
addition this can result in premature wear of the rear brake pads.•
Never leave children unattended in the vehicle. The children might, for
example, release the handbrake or take
the vehicle out of gear. The vehicle
might then move off - risk of accident!
Caution
After the car has come to a stop, always firs
t of all apply the handbrake firmly before
then additionally engaging a gear (manual gearbox) or moving the selector lever into position
P (automatic gearbox).
Rear parking aid*The parking aid provides a warning
of obstacles behind the vehicle.
The audible parking aid determines the di
stance between the rear bumper and an
obstacle located behind the ve
hicle with the aid of ultras
ound sensors. The tones of
the parking aid can be adapted in th
e menu of the information display*
⇒page 27.
The sensors are integrated in the rear bumper. Range of sensors The clearance warning begins at a distance
of about 160 cm from the obstacle (area
⇒ fig. 117
). The interval between the warning signals becomes shorter as the clear-
ance is reduced. A continuous tone sounds from
a distance of approx. 30
cm (area ) - danger area.
You should not reverse any further after this signal sounds!
If the vehicle is
equipped with a factory-fitted
towing device*, the border of the danger area starts,
continuous tone, 5 cm furt
her behind the vehicle. Th
e vehicle can be extended
through an installed deta
chable towing device.
On vehicles equipped with a factory-fitted
radio* or navigation system*, the distance
to the obstruction is shown graphically in the display. On vehicles with a factory-fitted towing device, the sensors are deactivated when towing a trailer. The driver is informed about this by a graphic display (vehicle towing
a trailer) in the radio* or the navigation*
display. The radio* or navigation system*, which is factory-fitted, can be set so that the play function volume decreases when acti
vating the parking ai
d, see Owner's Manual
radio* or navigation system*. This impr
oves the audibility of the parking aid.
Fig. 117 Parking aid: Detection range of rear sensors
AA
AB
sgg.6.book Page 113 Thursday, September 24, 2009 2:32 PM

Starting-off and Driving
114
Activating The parking aid is activated automatically when
reverse gear
is engaged and the igni-
tion is turned on. This is confirme
d by a brief acknowledgement signal.
Deactivating The parking aid is deactivated
by removing the reverse gear.
WARNING
•
The parking aid is not a substitute for the driver paying proper attention and
it is always the driver's responsibility to take care when parking the vehicle or carrying out similar manoeuvres.•
You should therefore satisfy yourself, befo
re reversing, that there is no small
obstacle, such as a rock, thin post, trailer drawbar etc., behind your vehicle. Such an obstacle might not be within the range detected by the sensors.•
Under certain circumstances, surfaces
of certain objects and types of
clothing cannot reflect the signal of
the parking aid. Thus, these objects or
people who wear such clothing are not re
cognised by the sensors of the parking
aid.
Note
•
The parking aid does not operate if you are towing a trailer (applies to models
which feature a factory-fitted towing device*).•
If a warning signal sounds for about 3 seconds after switching the ignition on and
engaging reverse gear, and there is no obstac
le close to your vehicle, this indicates a
system fault. Have the fault rectified by a specialist workshop.•
The sensors must be kept clean and free of ice to enable the parking aid to operate
properly.
Front and rear parking aid*The parking aid provides a warning of
obstacles in front and behind the
vehicle.Fig. 118 Activating the
parking aid / detection range of the front sensors
The audible parking aid determines the distan
ce between the front or rear bumper and
an obstacle with the aid of ultrasound sensors. The sensors are integrated in the front and rear bumper. The signal tones for the fr
ont parking aid sound higher as standard
than for the rear parking aid. The tones of the parking aid can be adapted in the menu of the information display*
⇒page 27.
Range of sensors The distance warning begins at a distance
of about 120°cm from the obstacle in front
of the vehicle (area
⇒fig. 118
) and about 160 cm from the obstacle behind the
vehicle (area )
⇒page 113, fig. 117
. The interval between the warning signals
becomes shorter as the clearance is reduced. A continuous tone sounds from
a distance of approx. 30
cm (area ) - danger area.
From this moment on do not continue driving!
If the vehicle is equipped with a
factory-fitted towing device*, the border of
the danger area starts - continuous tone -
5 cm further behind the vehicle. The vehi
cle can be extended through an installed
detachable towing device. On vehicles equipped with a factory-fitted
radio* or navigation system*, the distance
to the obstruction is shown graphically in the
display. On vehicles with a factory-fitted
towing device, the rear sensors are deactivated when towing a trailer. The driver is informed about this by a graphic display (vehic
le towing a trailer) in the radio* or the
navigation* display. The radio* or navigation
system*, which is factory-fitted, can be
AA
AA
AB
sgg.6.book Page 114 Thursday, September 24, 2009 2:32 PM

Starting-off and Driving
115
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
set so that the play function volume decr
eases when activating the parking aid, see
Owner's Manual radio* or na
vigation system*. This impr
oves the audibility of the
parking aid. Activating The parking aid is activated when the
reverse gear
is engaged and the ignition is
turned on or by pressing the button
⇒page 114, fig. 118
- the symbol lights up in
the button. The activation is confirme
d by a brief acknowledgement signal.
Deactivating The parking aid is deactivated after pressing the button°
⇒page 114, fig. 118
or at
a speed of more than 10 km/h - the symbol
 in the button is no longer illuminated.
WARNING
•
The parking aid is not a substitute for the driver paying proper attention and
it is always the driver's responsibility to
take care when reversing the vehicle or
carrying out similar manoeuvres.•
You should therefore satisfy yourself, befo
re reversing, that there is no small
obstacle, such as a rock, thin post, trailer drawbar etc., in front or behind your vehicle. Such an obstacle might not be
within the range dete
cted by the sensors.
•
Under certain circumstances, surfaces
of certain objects and types of
clothing cannot reflect the signal of th
e parking aid. Thus, these objects or
people who wear such clothing are not re
cognised by the sensors of the parking
aid.
Note
•
Only the front parking aid operates if yo
u are towing a trailer (applies only to
models which feature a factory-fitted towing device*).•
If a warning signal sounds for about 3 seco
nds after activating the system and there
is no obstacle close to your
vehicle, this indicates a system fault. The fault is confirmed
additionally when the symbol flashes in the button
⇒page 114, fig. 118
. Have the
fault rectified by a specialist workshop.•
The sensors must be kept clean and free of ice to enable the parking aid to operate
properly.
•
If the parking aid is activated and the sele
ctor lever of the automatic gearbox is in
the position , warning signal indicates inte
rruption (vehicle can no longer move).
Park Assist*Description and important informationThe park assist assists you when parking in a suitable parallel parking space between two vehicles or
behind a vehicle.
The park assist automatically searches for
suitable parking spaces
after switching on
the ignition and when driving up to 30 km/h. During the parking procedure the park assist only takes over the steering movements, the pedals continue to be operated by the driver. Function of the system is based on:•
Length and depth measurement of the parking spaces when driving
•
Evaluation of the size of the parking space
•
Definition of the correct position of the vehicle for parking
•
Calculating the line on which the vehicle drives backwards into the parking space
•
Actuation of the steering force assistance, automatic spinning of the wheels of the
front axle when parking.
WARNING
The park assist does not take away the responsability from the driver when parking.•
Pay particular attention to small children and animals as they would not be
recognised by the sensors of the parking aid.•
Under certain circumstances, surfaces of certain objects and types of
clothing cannot reflect the signal of the park assist or the parking aid. Thus, these objects or people who wear such clothing are not recognised by the sensors of the parking aid.



AP
sgg.6.book Page 115 Thursday, September 24, 2009 2:32 PM

Starting-off and Driving
116
•
The external sound source of the park
assist and the parking aid can be
disruptively influenced and under unfavourable conditions, objects or people cannot be recognised by the sensors of the parking aid.
Caution
•
If other vehicles are parked behind or on
the kurb, the park assist guides your
ve hicle be yond the kurb or onto it. Make s ure that the whee ls or the whe el rims of yo ur vehicle are not damaged and if necessary intervene in time.•
You should satisfy yourself before parking that there is no small obstacle, such as a
rock, thin post, trailer drawbar etc., in front
or behind your vehicle. Such an obstacle
might not be within the range detected by the sensors.•
Under certain circumstances, surfaces or st
ructures of certain objects such as wire
mesh fences, powder snow etc..., ca
nnot be recognised by the system.
•
The evaluation of the parking space and the parking procedure depends on the
circumference of the wheels. The system does not function correctly if your vehicle is mounted with wheels of non-permissible
size, snow chains or a temporary spare
wheel (in order to reach the nearest workshop). If the tyres other than those excepted by the manufacturer are mounted, the resulting position of the vehicle in the parking space can differ slightly. The parking assistant system automatically performs the correction of the wheel circumference when driving.•
The accuracy of the evaluation for the parking space can be influenced by the
incorrectly determined outside temperature if
the later is influenced by the thermal
radiation of the engine i.e for stop and go in a traffic jam.•
In order to avoid damaging th
e sensors while cleaning wi
th high-pressure cleaners
or steam jets, the sensors must only be
directly sprayed for short periods while a
minimum distance of 10 cm must be observed.
Note
•
A component of the park assist is the front and rear parking aid*.
•
The electronic stability programme (ESP*)
must always be switched on for the
parking procedure.
•
Only the front parking aid operates if yo
u are towing a trailer (applies only to
models which feature a factory-fitted towing de
vice*). This is why it is not possible to
park backwards with the help of the
park assist when towing a trailer.
•
The sensors must be kept clean and free of ice to enable the parking aid to operate
properly.Switch on display of the park a
ssist in the information display*
Fig. 119 Switching on the park assist / information display: Finding a suitable parking spaceSwitch on display of the park assist in the information display*– Press the button
⇒fig. 119
.
– Drive past the parking row up to maximum 30 km/h and with a distance of 0.5 m to
1.5 m
⇒fig. 119
.
Operate the turn signal for the driver's side if
you wish to park on this side of the road.
In the information display* the search area
for the parking space is indicated on the
driver's side. If you press the button at a speed greate
r than 30 km/h and less than 50 km/h, the
message indicating that the speed for detecting the space is exceeded will be displayed in the information display of the in
strument cluster. If the speed drops below
30 km/h, the condition of the parking assistant is automatically displayed in the infor-mation display of the instrument cluster. When exceeding the speed of 50 km/h, it is required to activate the displa
y again by pressing the button
⇒fig. 119
.
WARNING (continued)
sgg.6.book Page 116 Thursday, September 24, 2009 2:32 PM

Starting-off and Driving
117
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Note
•
If the park assist is switched on, a yell
ow warning light lights up in the button.
•
The search for suitable parking spaces is
automatic after switching on the ignition
at speeds of more than 30 km/h. Searching for a parking space is performed at the same time on the driver and front passenger side.•
If the sensors find a suitable parking space, they store its parameters until another
suitable parking space has been found or until
a distance of 10 m had been driven after
finding the parking space. This is why it is
possible to switch on the park assist after
driving past the parking space, the information on whether this parking space is suit- able for parking appears in the information display*.Parking with the help of the park assist and concluding the parking procedureFig. 120 Information display: the determined pa
rking space with the information to drive on
and for engaging the reverse gear
Fig. 121 Information display: Information for
engaging the forward gear or the reverse
gear The time limit for the parking procedure with the help of the park assist lasts 180 seconds. – If the park assist has recognised a suitable parking space, it is shown in the infor-
mation display*
⇒fig. 120
.
– Drive on further until the display
⇒fig. 120
appears.
– Bring the vehicle to a stop for at least 1 second.– Engage the reverse gear or set the selector lever* in the position
R.
– As soon as the following message is shown in the information display*:
Steering
interv. active. Monitor area around veh.!
, let go of the steering wheel, the
steering will be taken over by the system.
– Observe the surroundings and drive backwards with a speed of maximum 7 km/h,
at the same time operate the pedal.
– In the event that the parking procedure cannot be carried out in one go, proceed
to parking in further stages. If the forward arrow flashes in the information display* ⇒ fig. 121
, engage the forward gear.
– Observe the surroundings and drive forw
ards with a speed of maximum 7 km/h.
–If the backward arrow
⇒fig. 121
flashes in the information display*, once again
engage the reverse gear or move the selector lever* into the position
R and care-
fully drive backwards. You can repeat these steps several times.
AA
AB
AC
AD
AA
AB
AC
AD
sgg.6.book Page 117 Thursday, September 24, 2009 2:32 PM

Starting-off and Driving
118
– End the parking procedure from a distance on the basis of the information of the
system.
As soon as the parking procedure is comple
ted, an audible signal sounds and in the
information display* the following message appears:
Steering interv. finished.
Please take over steering!
.
Switch off park assist The park assist switches off during
one of the following occurences:
•
a speed of 30 km/h exceeded,
•
a speed of 7 km/h exceeded during the parking procedure,
•
a time limit of 180 seconds exceeded for the parking procedure,
•
the button pressed for the park assist,
•
parking aid activated,
•
intervention of the driver in the automatic steering procedure (stop the steering
wheel),•
Disengage reverse gear or take selector lever* out of the position
R when driving
backwards into the parking space. Further warning and information texts of the park assist in the information display*: Park Assist finished. The parking procedure has ended or after switching on the ignition, the vehicle has not been driven above 10 km/h. Park Assist: Speed too high! Reduce the speed below 30 km/h. Driver steering intervention!
Please take over steering!
The parking procedure is ended through driver intervention. Park Assist finished. ASR switched off The parking procedure cannot be carried ou
t because the TCS system is switched off.
ASR switched off. Please take over steering! The parking procedure was ended because the TCS system was switched off during the parking procedure. Park Assist finished. Trailer The parking procedure is not possible beca
use the trailer is hitched and a plug is
inserted in the socket of the towing device. Time limit exceeded. Please take over steering! The parking procedure was ended because a time limit of 180 seconds for parking was exceeded. System fault: Park Assist finished. The parking procedure is not possible becaus
e a fault exists on the vehicle. Have the
fault rectified by a specialist workshop. Park Assist defective. Workshop! The parking procedure is not possible because
a fault exists on the park assist. Have the
fault rectified by a specialist workshop. Steering interv. active. Mo
nitor area around veh.!
The park assist is active and takes over the steering movements. Observe the surroundings and carefully drive backward
s, at the same time operate the pedal.
Please take over steering!
Finish parking proc. manually
Take over the steering. End the parking procedure without using the park assist. Speed too high! Please take over steering! The parking procedure was ended while the speed was exceeded. Park Assist: ESP intervention! Intervention of the ESP system while searching for a suitable parking place. ESP intervention! Please take over steering! Parking procedure is ended through the intervention of the ESP system. Park Assist: Stationary time not sufficient. The stationary time of the ve
hicle was less than 1 second.
sgg.6.book Page 118 Thursday, September 24, 2009 2:32 PM

Starting-off and Driving
119
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Park Assist: Speed too low. After the ignition is switched on, the vehicle must exceed the speed of 10 km/h at least once.Cruise control system (CCS)*IntroductionThe cruise control system (CCS) maintains
a constant speed, more than 30 km/h (20
mph), once it has been set, without you havi
ng to depress the accelerator pedal. This
is only possible within the range which is permitted by the power output and braking power of the engine. The cruise control system
makes it possible - particularly on long
journeys - for you to rest your “accelerator foot”.
WARNING
•
The cruise control system must not, for safety reasons, be used in dense
traffic or on unfavourable road surfaces
(such as icy roads, slippery roads or
loose chippings) - risk of accident!•
In order to prevent unintentional use of the cruise control system, always
switch off the system after use.
Note
•
Models fitted with a manual gearbox: Always
depress the clutch pedal if you switch
on the cruise control system when the gearbox is in Neutral. Otherwise the engine can rev up unintentionally.•
The cruise control system is not able to
maintain a constant speed when driving on
steep downhill sections. The weight of the vehicle increases the speed at which it travels. One should shift down in good time
to a lower gear or slow the vehicle down
by applying the foot brake.•
It is not possible on vehicl
es fitted with an automati
c gearbox to switch on the
cruise control system if the selector lever is in the position
P, N or R.
Storing a speedThe cruise control system is operated by means of the switch and rocker button in the left lever of the multi-functional switch. – Press the switch
⇒fig. 122
into the position
ON
.
– After the desired speed has been reached, press the rocker button into the
SET

position.
After you have released the rocker button out of the position
SET
, the speed you
have just stored is maintained at a consta
nt speed without having to depress the accel-
erator. You can
increase
the speed by depressing the accelerator. Releasing the accelerator
will cause the speed to
drop
again to the set speed.
This does not apply, however, if you drive at a speed which is more than 10 km/h higher than the set speed for a period of longer than 5 minutes. The stored speed will be cancelled in the memory. You then have to re-store the desired speed. One can
reduce
the speed in the usual manner. The system is switched off temporarily
by actuating the brake or clutch pedal
⇒page 120.
WARNING
First ensure that it is not too high for the traffic conditions which exist at that moment before resuming the stored speed.
Fig. 122 Operating lever: Rocker button and switch of cruise control system
AA
AB
AA
AB
AB
sgg.6.book Page 119 Thursday, September 24, 2009 2:32 PM