suspension SSANGYONG KORANDO 1997 Service Repair Manual

0B -- 4 GENERAL INFORMATION
D AEW OO M Y_2000
Tire and Wheel
ApplicationSpecifications
Standard Tire SizeP235/75 R15, 255/70 R15
Standard Wheel Size7JJx15
Inflation Pressure At Full Lode
P235 / 75 : Front
Rear
P255 / 75 : Front
Rear
30 Psi
30 Psi
30 Psi
30 Psi
Steering System
ApplicationSpecifications
Gear TypeRACK & PINION
Wheel Alignment:
Front: Toe -- in
Front: Caster
Front: Camber
0--4mm
2°30′±30′
0°±30′
Oil Capacity1L
Suspension
ApplicationSpecifications
Front TypeDouble Wishbone
Rear Type5--Link
Fuel System
ApplicationSpecifications
Fuel Pump TypeElectric Motor Pump
Fuel Capacity70 L
Lubricating System
Application661LA662NA662LA2.0L
DOHC2.3L
DOCH3.2L
DOCH
Oil Pump TypeExternal Gear pump
Oil Filter TypeCombination (Full & Part)Full Flow
Oil Capacity (L)
(Including Oil Filter)8.09.09.57.27.58.2
Cooling System
Application661LA662NA662LA2.0L
DOHC2.3L
DOCH3.2L
DOCH
Coolant Capacity (L)9.5 -- 1010.510.5 -- 1110.510.511. 3
Radiator TypeForced Circulation
Water Pump TypeCentrifugal

0B -- 14 GENERAL INFORMATION
D AEW OO M Y_2000
EACH TIME THE OIL IS CHANGED
Brake System Inspection
This inspection should be done when the wheels are re-
moved for rotation. Inspect the lines and the hoses for
proper hookup, binding, leaks, cracks, chafing, etc. In-
spect the disc brake pads for wear. Inspect the rotors for
surface condition. Inspect other brake parts, the parking
brake, etc., at the same time. Inspect the brakes more
often if habit or conditions result in frequent braking.
Steering, Suspension and Front Drive Axle
Boot And Seal Inspection
Inspect the front and rear suspension and the steering
system for damaged, loose or missing parts, signs of
wear or lack of lubrication. Inspect the power steering
line and the hoses for proper hookup, binding, leaks,
cracks, chafing, etc. Clean and inspect the drive axle
boot and seals for damage, tears or leakage. Replace
the seals if necessary.
Exhaust System Inspection
Inspect the complete system (including the catalytic
converter if equipped). Inspect the body near the ex-
haust system. Look for broken, damaged, missing, or
out -- of -- position parts as well as open seams, holes,
loose connections, or other conditions which could
cause heat buildup in the floor pan or could let exhaust
fumes seep into the trunk or passenger compartment.
Throttle Linkage Inspection
Inspect the throttle linkage for interference or binding,
damaged, or missing parts. Lubricate all linkage joints
and throttle cable joints, the intermediate throttle shaft
bearing, the return spring at throttle valve assembly, and
the accelerator pedal sliding face with suitable grease.
Check the throttle cable for free movements.
Engine Drive Belts
Inspect all belts for cracks, fraying, wear and proper ten-
sion. Adjust or replace the belts as needed.
Hood Latch Operation
When opening the hood, note the operation of the sec-
ondary latch. It should keep the hood from opening all
the way when the primary latch is released. The hood
must close firmly.
AT LEAST ANNUALLY
Lap and Shoulder Belts Condition and Operation
Inspect the belt system including: the webbing, the
buckles, the latch plates, the retractor, the guide loops
and the anchors.
Movable Head Restraint Operation
On vehicles with movable head restraints, the restraints
must stay in the desired position.
Spare Tire and Jack Storage
Be alert to rattles in the rear of the vehicle. The spare
tire, all the jacking equipment, and the tools must be se-
curely stowed at all times. Oil the jack ratchet or the
screw mechanism after each use.
Key Lock Service
Lubricate the key lock cylinder.
Body Lubrication Service
Lubricate all the body door hinges including the hood,
the fuel door, the rear compartment hinges and the
latches, the glove box and the console doors, and any
folding seat hardware.
Underbody Flushing
Flushing the underbody will remove any corrosive mate-
rials used for ice and snow removal and dust control. At
least every spring clean the underbody. First, loosen the
sediment packed in closed areas of the vehicle. Then
flush the underbody with plain water.
Engine Cooling System
Inspect the coolant and freeze protection fluid. If the
fluid is dirty or rusty, drain, flush and refill the engine
cooling system with new coolant. Keep the coolant at
the proper mixture in order to ensure proper freeze
protection, corrosion protection and engine operating
temperature. Inspect the hoses. Replace the cracked,
swollen, or deteriorated hoses. Tighten the clamps.
Clean the outside of the radiator and the air conditioning
condenser. Wash the filler cap and the neck. Pressure
test the cooling system and the cap in order to help en-
sure proper operation.

OM600 ENGINE MECHANICAL 1B3 -- 177
D AEW OO M Y_2000
UNIT REPAIR
CYLINDER HEAD PRESSURE LEAKAGE TEST
Preceding Work : Removal of the cylinder head
Removal of the exhaust manifold
Removal of the valve
1 Feed Pipe
2Bolt
3 Return Connection
4 Gasket Replace.................................
5 Coolant Gallery Sealing..........................
6 Pressure Measuring Plate Completely tight to the cylinder head.................
7 Cylinder Head...........................
Immerse with pressure measuring plate into warm water of approx. 60_C and pressurize with compressed
air of 2 bar.
Notice
If air bubbles are seen, replace the cylinder head.
Tools Required
115 589 34 63 00 Pressure Measuring Plate
601 589 00 25 00 Suspension Device

SECTION 2A
SUSPENSION DIAGNOSIS
TABLE OF CONTENTS
Diagnosis..............................................................2A-2
General Diagnosis................................................2A-2Hub and Bearing.................................................2A-7

SSANGYONG MY2002
2A-2 SUSPENSION DIAGNOSIS
Inspect the tires for improper pressure and uneven wear.
Inspect the joint from the steering column to the steer-
ing gear for loose connections or wear.
Inspect the front and the rear suspension, the steering
gear, and the linkage for loose or damaged parts.
Inspect for out-of-round tires.
Inspect for out-of-balance tires, bent wheels, and worn
or loose wheel bearings.
Check the power steering pump serpentine belt tension.
Inspect the power steering system for leaks. Also, check
the power steering fluid level.Action
Checks
Checks
Inspect for incorrect toe on the front and the rear wheels.
Inspect for a twisted or a bent suspension arm. Inspect for mismatched or uneven tires.
Inspect for a broken or a sagging spring.
Inspect for a radial tire lateral force.
Check the front-wheel alignment.
Inspect for an off-center steering gear.
Inspect for front-brake dragging.
DIAGNOSIS
GENERAL DIAGNOSIS
Problems in the steering, the suspension, the tires,
and the wheels involve several systems. Consider all
systems when diagnosing a complaint. Some problems,
such as abnormal or excessive tire wear and scuffed
tires, may be the result of hard driving. Always roadtest the vehicle first. If possible, do this road test with
the customer.
Proceed with the following preliminary checks. Correct
any substandard conditions.
Preliminary Checks
Replace the tires.
Replace the spring.
Check the wheel alignment. Switch the tire and the
wheel assemblies. Replace the tires, as needed.
Align the front wheels.
Reseat the pinion valve assembly. Replace the pinion
valve assembly, as needed.
Adjust the front brakes.
Car Lead/Pull
Action
Adjust the toe on the front and the rear wheels.
Replace the suspension arm.
Scuffed Tires
Inflate the tires to the proper pressure.
Tighten the intermediate shaft pinch bolts. Replace the
intermediate shaft, as needed.
Tighten the front and the rear suspension. Tighten the
steering gear mounting bracket bolts. Tighten the inter-
mediate shaft pinch bolts. Replace the front and the rear
suspension, as needed. Replace the steering gear, as
needed. Replace the intermediate shaft, as needed.
Perform a free runout test. Match-mount the tires.
Balance the wheels. Replace the wheels. Replace the
wheel bearings.
Tighten the power steering pump serpentine belt.
Repair any leaks. Perform a power steering system test.
Add power steering fluid, as needed.
Action Checks

SUSPENSION DIAGNOSIS 2A-3
SSANGYONG MY2002
Perform a rack bearing preload adjustment.
Replace the seals and the hoses, as needed.
Lubricate the steering gear. Repair or replace the
steering gear, as needed.
Tighten the steering gear mounting bracket nuts and
the bolts. Check the steering gear preload adjustment.
Check the hydraulic system. Test the power steering
system pressure with a gauge.
Inspect for binding or catching in the steering gear.
Inspect for a loose steering gear mounting.Action ChecksBalance the tire or the wheel.
Measure the hub flange runout. Replace the hub, as
needed.
Adjust the brakes. Replace the brake rotor, as needed.
Replace the outer tie rods.
Balance the wheel.
Replace the lower ball joint.
Measure the wheel runout. Replace the wheel, as
needed.
Match-mount the tire and the wheel assembly. Inspect for an out-of-balance tire or wheel.
Inspect for excessive wheel hub runout.
Inspect for excessive brake rotor imbalance.
Inspect for worn tie rod ends.
Inspect for wheel trim imbalance.
Inspect for a worn lower ball joint.
Inspect for excessive wheel runout.
Inspect for excessive loaded radial runout on the tire
and the wheel assembly.Action ChecksAction
Balance the tire or the wheel. Checks
Inspect for an out-of-balance tire or wheel.Align the front and the rear wheels.
Adjust the toe on the front and the rear wheels.
Replace the spring.
Balance the tires.
Rotate the tires. Replace the tires, as needed.
Maintain the proper load weight.
Inflate the tires to the proper pressure. Check the front-wheel and the rear-wheel alignment.
Inspect for excessive toe on the front and the rear wheels.
Inspect for a broken or a sagging spring.
Inspect for out-of-balance tires.
Check for a failure to rotate tires.
Check for an overloaded vehicle.
Inspect for low tire inflation.
Abnormal or Excessive Tire Wear
Shimmy, Shake, or Vibration
Hard Steering
Wheel Tramp
Action Checks

SSANGYONG MY2002
2A-4 SUSPENSION DIAGNOSIS
Replace the tires.
Replace the ball joints and the outer tie rods.
Replace the dampeners.
Tighten the stabilizer link.
Replace the spring.
Perform a rack bearing preload adjustment.
Align the front and the rear wheels. Inspect for mismatched or uneven tires.
Inspect for lack of lubrication of the ball joints and the
tie rod ends.
Inspect for worn dampeners.
Inspect for a loose stabilizer link.
Inspect for a broken or a sagging spring.
Check the steering gear preload adjustment.
Check the front-wheel and the rear-wheel alignment.Action ChecksReplace the ball joints and the outer tie rods.
Replace the damaged suspension components.
Replace the control arm bushings or the tie rods.
Tighten the stabilizer link.
Tighten the wheel nuts.
Tighten the suspension bolts or the nuts. Inspect for a lack of lubrication of the ball joints and
the tie rod ends.
Inspect for damaged suspension components.
Inspect for worn control arm bushings or tie rod ends.
Inspect for a loose stabilizer link.
Inspect for loose wheel nuts.
Inspect for loose suspension bolts or nuts.Action Checks Inspect for lack of lubrication of the ball joints and the
tie rod ends.
Inspect for binding in the ball joints.
Inspect for binding in the steering column.
Check the front-wheel alignment.
Check the steering gear preload adjustment.
Inspect for a sticking valve.
Inspect for binding in the intermediate shaft on the
steering gear.Action ChecksReplace the front wheel bearings.
Tighten the steering gear mounting bracket nuts and
the bolts.
Tighten the intermediate shaft pinch bolts. Replace the
intermediate shaft, as needed.
Perform a rack bearing preload adjustment. Inspect for worn or loose front wheel bearings.
Inspect for a loose steering gear mounting.
Inspect the joint from the column to the steering gear
for loose connections or wear.
Check the steering gear preload adjustment.Action Checks
Replace the ball joints and the outer tie rods.
Replace the ball joint.
Lubricate the steering column. Replace the steering
column as needed.
Align the front wheels.
Perform a rack bearing preload adjustment.
Lubricate the pinion valve assembly. Replace the pin-
ion valve assembly, as needed.
Replace the intermediate shaft.
Poor Returnability
Abnormal Noise, Front Suspension
Abnormal or Excessive Tire Wear
Too Much Playin Steering

SUSPENSION DIAGNOSIS 2A-5
SSANGYONG MY2002
Action Checks
Replace the dampeners.
Maintain the proper load weight.
Replace the spring. Inspect for worn dampeners.
Check for an overloaded vehicle.
Inspect for a broken or a sagging spring.Tighten the stabilizer link.
Maintain the proper load weight.
Replace the spring. Inspect for a loose stabilizer link.
Check for an overloaded vehicle.
Inspect for a broken or a sagging spring.Action ChecksAction Checks
Replace the dampeners.
Replace the spring. Inspect for incorrect dampeners.
Inspect for an incorrect spring. Inspect for worn dampeners.
Inspect for a broken or a sagging spring.Replace the dampeners.
Replace the spring.Action ChecksReplace the spring.
Maintain the proper load weight.
Replace the spring. Inspect for a broken or a sagging spring.
Check for an overloaded vehicle.
Inspect for an incorrect or weak spring.Action Checks Inspect for worn or loose front wheel bearings.
Inspect for a broken or a sagging spring.
Inspect for a leaking wheel cylinder or caliper.
Inspect for warped rotors.
Inspect for an incorrect or an uneven caster.Replace the front wheel bearings.
Replace the spring.
Replace the wheel cylinder or the caliper.
Replace the rotors.
If the caster is beyond specifications, check the frame
and repair it, as needed.Action Checks
Low or Uneven Trim Height
Ride Too Soft
Ride Too Harsh
Body Leans or Sways in Corners
Suspension Bottoms
Erratic Steering when Braking

SSANGYONG MY2002
2A-6 SUSPENSION DIAGNOSIS
Check the front-wheel and the rear-wheel alignment.
Inspect for worn dampeners.
Inspect for worn or loose wheel bearings.
Inspect for excessive tire or wheel runout.
Inspect for a worn ball joint.
Check the steering gear preload adjustment.Align the front and the rear wheels.
Replace the dampeners.
Replace the wheel bearings.
Match-mount the tires. Replace the tires, as needed.
Replace the wheels, as needed.
Replace the ball joint.
Perform a rack bearing preload adjustment.Action ChecksReplace the seals and the hoses, as needed.
Clean the pinion valve assembly. Replace the pinion
valve assembly, as needed.
Adjust the power steering pump serpentine belt. Check the hydraulic system. Test the power steering
system pressure with a gauge.
Inspect for a sluggish steering gear valve.
Inspect for a loose power steering pump serpentine
belt.Action ChecksAction Checks
Purge the power steering system of air.
Tighten the steering gear mounting bracket nuts and
the bolts.
Tighten the intermediate shaft pinch bolts. Replace the
intermediate shaft, as needed.
Tighten the tie rod ends. Replace the outer tie rods, as
needed.
Replace the front wheel bearings. Inspect for air in the power steering system.
Inspect for a loose steering gear mounting.
Inspect the joint from the column to the steering gear
for loose connections or wear.
Inspect for loose tie rod ends.
Inspect for loose or worn front wheel bearings.
Steering Wheel Surges or Jerks
Cupped Tires
Steering Wheel Kickback

SUSPENSION DIAGNOSIS 2A-7
SSANGYONG MY2002
KAA2A010
HUB AND BEARING
Perform the following test to check for looseness in
the hub and bearing assembly:
1. Raise and suitably support the vehicle.
2. Remove the rear wheel. Refer to Section 2E, Tires
and Wheels.
3. Remove the caliper and the disc brake rotor. Refer
to Section 4E, Rear Disc Brakes.
4. Mount a dial indicator set with a magnetic base to
a stationary part of the vehicle.
5. Push and pull the wheel hub by hand. If the wheel
hub movement exceeds 0.03 mm (0.001 inch),
replace the hub and bearing assembly. Refer to
Section 2D, Rear Suspension.
6. Install the caliper and the disc brake rotor. Refer
to Section 4E, Rear Disc Brakes.
7. Install the rear wheel. Refer to Section 2E, Tires
and Wheels.
8. Lower the vehicle.