air condition SSANGYONG KORANDO 2013 Workshop Manual

6810-00
Intake sensor
It is mounted to the side of
evaporator core and detects the
temperature of the evaporator
core.Water temperature
sensor
It is mounted to the heater pipe
part and detects the coolant
temperature.
3) Air Conditioner Module Layout
Temp actuator
It changes the air mix door
opening according to the
control command from the
heater and A/C control
assembly.Evaporator core
It cools the surrounding air by
passing through the low-
temperature and low-pressure
refrigerant sprayed from the
expansion valve.
Heater core
It is mounted to the left-hand of
the air conditioner module and
heats the indoor using the heat
of the engine coolant.
Mode actuator
It controls the air outlet damper
to the five directions according
to the control command from
the heater and A/C control
assembly.

2) Function
(1) Function of heater and A/C control assembly with FATC
LCD display
Indoor set temperature indicator
AUTO mode operation indicator
A/C operation indicator
Defrost mode indicator
Fresh air mode indicator
Air recirculation mode indicator
Vent & foot mode indicator
Fan speed indicator 1.
2.
3.
4.
5.
6.
7.
8.
Temperature control dial
To set the temperature, turn the dial to the left or
right. The LCD display shows the set
temperature.
AUTO switch
When pressing this switch, "AUTO" is shown on
the display and the fan speed and air distribution
mode are adjusted automatically to keep interior
temperature to the set temperature.
ON/OFF switch
Pressing the switch turns the FATC on/off. When
the FATC is turned on, it memorizes the previous
status before becoming off.
Defroster mode switch
This is used to remove the condensation from the
windshield. When you press the switch, the
indicator comes on and the air distribution is
changed to the windshield at the same time, then
the air conditioner starts to operate. When you
press the switch again, the indicator goes off and
the air distribution returns to the previous status.

6810-00
Air distribution switch (switches in order)
Indoor temperature sensing part
The incar sensor is mounted to the rear of the
FATC and detects the interior air temperature
drawn through the air inlet.
Air source selection switch
When the switch is pressed, the indicator comes
on and the mode is switched to the recirculation
mode at the same time. When pressed again, the
indicator goes out and switched to the fresh air
mode at the same time.
Fan speed dial
Turn the dial to the left or right to adjust the fan
speed in 8 steps and the fan speed can be
checked through the LCD display.
A/C switch
When the switch is pressed, the indicator comes
on and the air conditioner starts at the same time.
Pressing the switch again goes out the indicator
and stops the air conditioner at the same time.

6810-00
(4) Air source control
The air source selection is made by the intake actuator. The driver can see the air source mode through
the switch's indicator and the LCD display.
Manual control
Press the air source selection switch to control the air source selection door manually. The air source
mode is switched
between the fresh air and recirculation alternatively each time the switch is pressed.
Auto control
In auto mode, the basic setting for the air source is fresh air. When the ambient temperature is high
during cooling,
the air source is changed from fresh air to recirculation to lower the temperature.
Control by vehicle speed (heating)
The air source selection is controlled in accordance with the vehicle speed while driving. Operating
conditions and control process are as follows:
AUTO mode
When the vehicle speed is 45 km/h or lower in fresh air mode, the air source door is open 30% of its
maximum opening. If the vehicle speed is 65 km/h or more, then
the air source door is completely open. -
-
and the electric fan 7.5V or higher.
Air source selection switch
LCD display (air source mode view)

Auto control
The air flow mode is controlled automatically in accordance with the vehicle indoor conditions.
But it is controlled as described below during initial driving (after overnight parking) in cold weather:

6810-00
(6) A/C control
The air conditioner is controlled by the A/C compressor of the engine ECU according to the signal from
the heater and A/C control assembly. The driver can see the air conditioner operation through the LCD
display and the indicator of the A/C switch.
Manual control
Pressing the A/C switch or selecting defrost mode turns on the A/C.
Auto control
The A/C is controlled in accordance with the indoor temperature and ambient temperature.
or below) in winter, the compressor is turned off to protect the A/C compressor.
A/C switch
LCD display (A/C operation view)

(7) Self-diagnosis
Diagnostic trouble code
The FATC has a self-diagnosis function that can diagnose the system by itself. If this system is
defective, the LCD display shows the diagnostic trouble code (DTC) to inform a driver of defects on the
device such as a sensor or actuator. The driver can see the each sensor data on the air conditioning
system after entering self-diagnosis mode. Before checking each component, be sure to check the
default code by using self diagnosis function.
The diagnostic trouble code (DTC)
flashes twice and is displayed
repeatedly in order as long as a
separate operation is not performed.
Code Defective part
00 Normal
21 Ambient temperature sensor
22 Incar sensor
23 Water temperature sensor
24 Intake sensor
26 Temp door (control)
31 Mode door (vent)
32 Mode door (bi-level)
33 Temp door (cool)
34 Mode door (foot)
35 Mode door (defroster & foot)
36 Mode door (defroster)
37 Intake door (fresh air)
38 Intake door (1/3)
39 Intake door (recirculation)Diagnostic trouble code
Open circuit in sensor
Diagnostic trouble code

If the ON/OFF switch of the FATC is pressed for more than 5 seconds within 10 seconds after turning
the ignition key from the "OFF" position to the "ON" position, all the segments in LCD display comes on
for 3 seconds. 1.
The LCD display shows "2" and starts to check the sensor and actuator in the air conditioning system
automatically. 2.
3.
The self diagnosis ends when turning the ignition key from the "OFF" position to the "ON" position or
pressing the AUTO mode switch. 4.
Press for more
than 5 sec.
Segments comes on for 3 sec.

4. MTC SYSTEM OPERATION PROCESS
1) Input/Output Factors
The MTC (Manual Temperature Control) system controls all the actuator and blower motor by the driver.
The heater and A/C control assembly with MTC has the dials and switches with the indicators so that the
driver can know the air conditioning system's operation.

6810-00
2) Function
(1) Function of heater and A/C control assembly with MTC
Fan speed dial
Turn the dial to the left
or right to adjust the fan
speed in 7 steps.
A/C switch
When the switch is
pressed, the indicator
comes on and the air
conditioner starts at the
same time. Pressing the
switch again goes out
the indicator and stops
the air conditioner at the
same time.
Vent mode switch
If the switch is pressed, the
indicator comes on while the
air flows to the upper part of
the body.
Bi-level mode switch
If the switch is pressed, the
indicator comes on while the
air flows to the footwell and
the upper part of the body.
MAX A/C control switch
This is designed for increasing driver
comfort. When the switch is pressed,
the indicator comes on and the air
conditioner starts at the same time
and vent and recirculation modes are
selected automatically.Defroster mode switch
This is used to remove the
condensation from the
windshield. When you press the
switch, the indicator comes on
and the air distribution is
changed to the windshield at
the same time, then the air
conditioner starts to operate.Defroster & foot mode
switch
If the switch is pressed,
the indicator comes on
while the air flows to the
footwell and the
windshield.
Foot mode switch
If the switch is pressed, the indicator
comes on while the air flows to the
footwell.
Temperature
control dial
Turn the dial to the
left or right to adjust
the set temperature.
Air source selection
switch
When the switch is pressed, the
indicator comes on and the
mode is switched to the
recirculation mode at the same
time. When pressed again, the
indicator goes out and switched
to the fresh air mode at the
same time.