SSANGYONG KORANDO 2013 Service Manual

Front room lamp switch
The driver/passenger room lamps turns on
when pressing in these switches.Door coupled operation switch
The front room lamp and center room
lamp come on when opening a door with
this switch pressed in.
Sunroof switch
Push up the switch briefly: 2-step auto sliding open
Push up and hold the switch: manual sliding open
When pushing up the switch briefly, the sunroof is automatically opened. Opening is carried out
in 2 steps. In first step, the area 5 cm behind the sunroof is not opened. Push up the switch once
again in order to open the sunroof completely. The sunroof operation stops if you operate the
switch during its operation.
The sunroof is opened as long as pushing up the switch.
Pull down the switch briefly: auto sliding close
Pull down and hold the switch: manual sliding close
When pulling down the switch briefly, the sunroof is automatically closed. To stop the closing
sunroof, operate the switch to either direction.
The sunroof is closed as long as pulling down the switch.

8510-00
Door coupled room lamp operation and dimming control
When opening any of doors while the room lamp switch in overhead console is pressed in ("Door"
coupled position), the front and center room lamps come on. If the key is removed and door stays open,
the room lamps automatically goes off after 10 minutes. The sleep mode will be deactivated when the
door is locked or closed with the lamp OFF automatically.
When closing the door with IGN ON, the room lamps go off immediately.
When closing the door with IGN OFF, the room lamps stay on for 2 seconds more and are dimmed
out the side fascia panel.
When turning the ignition switch to ON position during dimming out operation, the room lamps go off
immediately.
When receiving the door unlock signal with IGN OFF, key removed and door closed, the overhead
console room lamp/center room lamp come on for 30 seconds.
For specification with the SKM, the lamps come on by the REKES unlock or passive unlock
signal.
When receiving the door unlock signal again while the lamps stay on by the REKES or passive
unlock signal, the overhead console/center room lamps stays on for 30 seconds more. (the lamps
stay on when receiving door unlock signal)
When opening a door during the coupled operation and dimming operation, the room lamps stays
ON. When closing it again, the lamps stay on for 2 seconds more and are dimmed out for 3 seconds.
While the room lamps dim out when the driver/passenger/rear doors are open and closed, they go off
immediately when entering into the theft deterrent mode.
The room lamps come on when AUTO approach signal is received. 1.
2.
3.
4.
5.
6.
7.
8.

Sunroof warning control
When removing the ignition key with the sunroof open (without SKM) or when opening the driver door
with IGN OFF or ACC and sunroof open (with SKM), the indoor buzzer sounds for 10 seconds with
the interval of 0.02s ON/1.58s OFF.
When opening and closing the driver door or closing the sunroof during indoor buzzer operation, the
buzzer stops its operation immediately.
When closing the driver door or sunroof and opening again during warning operation, the sunroof
warning does not work. If the condition is met after the ignition switch is turned to "ON" position again,
the indoor buzzer sounds for 10 seconds with the interval of 0.02s ON/1.58s OFF.
The sunroof warning has a priority over the tail lamp ON warning. 1.
2.
3.
4.

8510-00
Tailgate open switch
7. TAILGATE SWITCH

Tailgate open
When pressing the tailgate switch for more than 0.1 second with driver door unlocked and vehicle
power OFF, ACC ON or IGN ON. However, it is turned ON when the vehicle speed is below 3
The tailgate open relay is turned OFF immediately after the driver door is locked or the vehicle speed
goes over 3 km/h with IGN ON during its operation. However, the BCM does not operate if the tailgate
open switch is pressed when the vehicle speed is above 3 km/h. 1.
2.
open - Without SKM
When pressing the tailgate switch for more than 0.1 second with driver door unlocked and vehicle
The tailgate open relay is turned OFF immediately after the driver door is locked or the vehicle speed
goes over 3 km/h during its operation.
When the tailgate switch on smart key is pressed in theft deterrent mode or with the smart key
detected by the exterior antenna, the SKM verifies the smart key and disarms the tailgate only. When
the tailgate is open and closed, the system enters into the theft deterrent mode again. If the tailgate
switch is not operated for 30 seconds, the system also does so.
The BCM checks that the verified smart key is in the luggage room 1 second after when the closed
tailgate is detected by the tailgate open switch with power OFF.
If there is a verified smart key in the luggage room when the tailgate is open and closed in theft
deterrent mode, the external buzzer sounds for 5 seconds.
When the driver press the tailgate open switch in order to look for the smart key, the BCM deactivates
lock so that the tailgate can be opened even though the driver door is locked. (maintains standby for
opening without verification) 1.
2.
3.
4. With SKM

8310-00
1. LAMP SPECIFICATIONS
1) Exterior Lamps
2) Interior Lamps
Description Numbers Specification
Front room lamp 2 10W
Glove box lamp 1 5W
Center room lamp 1 10W
Luggage lamp 1 10W
Door courtesy lamp 2 5W
Description Numbers Specification
Headlamp High beam 2 H1-55W
Low beam 2 H7-55W
Turn signal lamp 2 P21W
Position lamp - LED
Front fog light 2 H16-19W
Rear fog light 2 21W
Side repeater - LED
Rear combination lamp Tail lamp - LED
Turn signal lamp 2 PY21W
Back-up lamp 2 W16W
Stop lamp 2 P21W
License plate lamp 2 W5W
High mounted stop lamp - LED
Puddle lamp 2 LED

Luminous intensity is a measure for the amount of light which passes through the unit area per
time unit. The SI unit of luminous intensity is the candela (cd), an SI base unit. -Luminous Intensity
Luminance describes the amount of light that passes through or is emitted from a particular area,
and falls within a given solid angle. It is measured in sb or nt. -Luminance
This indicates the amount of light reaching a given area. Measuring unit is lux (lx) and it is not
directly proportional to the brightness of the area as the reflection rate is not included. -Intensity of illumination
The LED stands for "Light Emitting Diode" or "Luminescent Diode." LED is a semiconductor diode
that emits incoherent narrow-spectrum light when electrically biased in the forward direction of the
p-n junction, as in the common LED circuit. In short, it is an element that converts electric signals
into light signals. Yellow, blue, red and white LEDs are currently available.
The followings are the advantages of LED.
It is not glaring and doesn't have short circuit unlike the conventional lamps.
It is semi-permanent and doesn't generate heat.
Its power consumption is much lower than those of conventional bulbs. -
-
Pin No. Specification
Operating voltage 9 V to 16 V
Load Max. 200 mA (relay load)
Operating temperature
Storage temperature
Mounting location Top center of inner side of windshield glass
2. AUTOMATIC LIGHT SENSOR SPECIFICATIONS

8310-00
3. MAJOR CHANGES
Front side
Headlamp
- Headlamp (high/low beam) dualized and tail lamp changed to LED type
Fog lamp
- Fog lamp design changed
Headlamp
(high/low beam)Turn signal lamp
Tail lampTurn signal lamp
Tail lamp,
DRL (EU)*
Headlamp
(high beam)
Headlamp
(low beam)

Rear side
Rear combination lamp
- Rear combination lamp design and its function changed
- Tail lamp (stop lamp) changed to LED type
Backup lamp
Turn signal
lamp
Stop/tail lamp
Rear fog
light
Tail lamp
Stop lamp,
Rear fog
light (EU)
Turn signal
lamp
Backup lamp
Stop lamp

8310-00
Indoor
Front door courtesy lamp
- Door courtesy lamp design changed due to modified front door trim