SSANGYONG KORANDO 2013 Service Manual

Tip switch (D-)
Gear change switch
-Change up
SEEK UP/DOWN switch
Volume UP/DOWN switch
Increases/decreases volume
Tip switch (D-)
Gear change switch
-Change down
CD mode
Select next/previous track and
FF/REW
Radio mode
Change frequency UP or DOWN
Press and hold to auto search -
-
MUTE & MODE switch
To eliminate the sound (MUTE), briefly
press this switch. To change the audio
mode (Radio-CD-USB-AUX-Radio), press
and hold this switch.
Handsfree switch
To make/receive/end a call,
press and hold this switch.

8510-00
Multifunction wiper switches
2) Multifunction Switch
Multifunction light switches
Light switch
Front wiper switch
Wiper speed dial
Rear wiper switch Front fog lamp switch
Front auto washer switch The multifunction switch contains the auto washer and wiper switch, front fog lamp switch and auto
hazard warning flasher switch. For the vehicle with air bag, since the contact coil is fitted to the upper part
of the multifunction switch and ESP steering wheel angle sensor is fitted to upper part of the contact coil,
pay attention to when removing and fitting or checking the wiring.

Light switch
Headlamps ON
Headlamp, side-marker, tail,
license plate, fog, and
instrument cluster lamps come
on.
Tail lamp ON
Side-marker, tail, license plate,
fog, and instrument cluster
lamps come on.
Automatic light ON
Head- and tail lamps
automatically turn on or off based
upon the intensity of the sunlight
analyzed by the automatic light
sensor.Lights OFF
High beam ON
To turn on the headlamp high
beam, push the lever towards
the instrument cluster with the
headlamp low beam on.Right turn signal lamp blinks
Passing
Regardless of the position of the light
switch, when holding the lever toward the
steering wheel, the headlights are on high
beam during the hold.Front fog lamp switch
To turn on the fog lights, turn this
switch while the tail lamps or
headlamps are turned on. Left turn signal lamp blinks

8510-00
position and release it, the windshield
wipers operate one wiping cycle. The
wipers will operate continuously if the
switch is held in this position.
Front automatic wiping speed control switch
The interval of wiping speed can be adjusted by turning the
control knob upward or downward when the windshield
wiper switch is in AUTO position.
Fast: Fast interval
Slow: Slow interval Wipers are not in operation.
Operates automatically
according to the vehicle speed
and amount of rainfall.
Continuous wipe, fast operation Continuous wipe, slow
operation MIST
OFF
AUTO
LO
HI Auto washer switch
If pressing the switch when the wiper
switch turns to the "OFF" position,
washer fluid is sprayed once and
wiper operates 4 times.
After a while, washer fluid is sprayed
once more and the wiper operates 3
times. Wiper switch

Rear wiper switch
Type B
Type AWindshield Washer Operation
lever toward you to spray washer
fluid on the windshield and to
operate the wipers 1~3 cycles.
Pull the lever briefly (for less than 0.6
seconds): One wiping cycle with
washer spray
Pull and hold the lever for more than
0.6 seconds: Three wiping cycles
with washer spray
The spray and wiper operation will
continue until you release the lever.
TYPE B
When the switch is fully turned, washer fluid will be sprayed onto the rear window
glass and the wiper will also operate. When the switch is released, it will return to
Rear wiper is not in operation.
TYPE A
INT
Rear wiper operation
(Intermittent)
ON
Rear wiper operation
(Normal Speed)
Rear wiper operation
When the switch is fully turned, washer fluid will be sprayed onto the rear window
glass and the wiper will also operate. When the switch is released, it will return to
the Rear Wiper Operation mode and only the wiper will keep operating.

8510-00
3) Cruise Control Switch
Cruise control switch
The cruise control is an automatic speed control system that maintains a desired driving speed without
using the accelerator pedal. The cruise control switch is fitted to the bottom right section of the steering
wheel. When this switch is operated, the AUTO CRUISE or ECO lamp on the instrument cluster comes
on.
The cruise control switch has a fivefold switch in it. The engine ECU can determine the current driving
condition since the resistance varies depending on the operation of the switch.
The cruise control system is operated at vehicle speed of between 38 km/h and 150 km/h. The manual
transmission is operated in the range of 3rd gear or higher.
This function can be used at the following traffic condition. (It is important to be careful for using this
function)
Cruise control (ON)
Cruise control (OFF)
Cruise control (Acceleration)Cruise control (Deceleration)
Cruise control (Reset)

Horn (high) Horn (low)
Theft deterrent horn
Theft deterrent horn
4) Horn Switch
Two horns are installed in the radiator grille at the bottom of both sides (one on each side). There is
another horn installed at the bottom of the battery tray side in the engine compartment for theft alarm.
Operating the horn switch on the steering wheel applies the power to the horn relay to operate both
horns (Dual horn). The theft deterrent horn is controlled by the BCM in armed mode regardless of the
horn relay operation.
Horn (dual horn)
Horn switch

8510-00
Front seat heating and ventilation switch (2-
level of driver seat heating and ventilation, 2-
level of passenger seat heating)
A. Driver seat heating switch
B. Driver seat ventilation switch
C. Passenger seat heating switch
5. SEAT HEATING AND VENTILATION SWITCH
1) Front Seat Heating and Ventilation Switch Overview (2-level of
Driver Seat Heating and Ventilation, 2-level of Passenger Seat
Heating)
The temperature of the seat can be adjusted in 3
seat heated wire and ventilation switch. Every
time the seat heating and ventilation switch is
pressed, the temperature level goes down by
one level. Pressing the switch a third time will turn
off the operation. Pressing the desired side of the
switch heats the seat cushion and seatback or
activates the seat ventilation function. The
temperature of the seat is kept uniform by cutting
off or connecting power through thermistor fitted
in the seat. The seat heating and ventilation unit
controls the rpm of the motor using PWM control
to operate the seat ventilation.
Front seat heating & ventilation switch (2-level of driver seat heating and ventilation, 2-level of
passenger seat heating)-
-
The front seat heating and ventilation functions cannot be operated at the same time.
The front seat heating and ventilation switch functions only when the engine is started. -
-Seat heating and ventilation unit & switch application

Front seat heating switch
A. Driver seat heating switch
B. Passenger seat heating switch
Rear seat heating switch
A. Rear LH seat heating switch A. Rear RH seat heating switch
The front seat heating switch can be operated to
the desired temperature (LO/HI) by pressing the
the seat heating switch to heat the seat and
seatback. When the temperature reaches 40
connects and cuts the power to keep the
temperature stable. There is no separate seat
warmer unit to control the temperature of the seat
heating system.
2) Front Seat & Rear Seat Heating Switch Overview
LH RH
The front seat and rear seat heating switches operates with IGN ON.
The seat heating and ventilation unit is not fitted in a vehicle without seat ventilation function. -
-

8510-00
Overhead console switch
6. OVERHEAD CONSOLE SWITCH
The front room lamp is controlled by the BCM.
The front room lamp comes on when opening the driver or passenger door. (door coupled operation
switch ON)
When closing the driver or passenger door, the front room lamp comes on for 2 seconds and then
dims down for 3 seconds. (door coupled operation switch ON)
The front room lamp turns on/off depending on the operation of the front room lamp ON/OFF switch
(spot switch). -
-
-
-
Front room lamp switch
Door coupled operation switch
Sunroof switch
Front room lamp connector
Sunroof connector