engine coolant SSANGYONG MUSSO 1998 Workshop Owners Manual

M162 ENGINE CONTROLS 1F1-73
Oxygen Sensor Signal Voltage Inspection
1. Measure the oxygen sensor signal voltage between the ECU
terminal No.11 and No.9. Maintain the engine speed ia at
idle while the coolant temperature is over 80°C.
If the measured value is not within the specified value, the
possible cause may be in cable, oxygen sensor or ECU.
Oxygen Sensor Heating Voltage Inspection
1. Measure the oxygen sensor heating voltage between the
ECU terminal No.11 and No.9. Maintain the engine speed ia
at idle while the coolant temperature is over 80°C.
If the measured value is not within the specified value, the
possible cause may be in cable, oxygen sensor or ECU.
Oxygen Sensor Heating Current Consumption
Inspection
1. Measure the oxygen sensor heating current consumption
between the ECU terminal No.9 and No.5 while the ignition
switch is in "ON" position.
If the measured value is not within the specified value, the
possible cause may be in cable, oxygen sensor or ECU.
Specified Value 0.2 - 2.0 A
Specified Value -0.2 - 1.0 V
Specified Value 11 - 14

M162 ENGINE CONTROLS 1F1-75
COOLANT TEMPERATURE SENSOR
1 Artificial Resin Housing
2 Metal Housing
3 NTC (negative temperature coefficient) Resistor
Removal & Installation Procedure
1. Remove the pressure by opening the pressure cap in the
coolant subtank.
2. Disconnect the connector and remove the coolant
temperature sensor.
Installation Notice
Replace the seals with new one.
3. Installation should follow the removal procedure in the
reverse order.
4. Check for leaks at each connections after starting the engine.4 Connector
5 Coolant Temperature Sensor
Tightening Torque 18 - 22 Nm

1F1-76 M162 ENGINE CONTROLS
2. Measure the resistance between the coolant temperature
sensor terminal No.1 and No.4 with the coolant temperature
sensor disconnected.
Inspection
1. Measure the coolant sensor input voltage between the ECU
terminal No.79 and No.78 while the ignition switch in "ON"
position.
Notice
Replace wiring and coolant temperature sensor if out of
specified value.
allowable error :±5%
allowable error :±5%
Voltage (V)
3.57
1.22
0.78
Temperature (°C)
20
30
40
Resistance (W)
2,500
322
185
Temperature (°C)
20
30
40

M162 ENGINE CONTROLS 1F1-77
Service Data
Resistance characteristic curve according to the coolant
temperatureTemperature(°C) Resistance(W) Voltage(V) Temperature(°C) Resistance(W) Voltage(V)
-40 48,550 4.8991 60 594 1.8632
-30 27,000 4.8214 70 434 1.5132
-20 15,670 4.7001 80 322 1.2179
-10 9,450 4.5215 90 243 0.9775
0 5,890 4.4273 100 185 0.7806
10 3,790 3.9562 110 143 0.6255
20 2,500 3.5714 120 111.6 0.5020
30 1,692 3.1426 130 88.0 0.4044
40 1,170 2.6959 140 71.2 0.3323
50 826 2.2618 - - -

SECTION 1F2
M161 ENGINE CONTROLS
TABLE OF CONTENTS
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise
noted.
Specifications . . . . . . . . . . . . . . . . . . . . . . . 1F2-2
Fastener Tightening Specifications . . . . . . . . 1F2-2
Special Tools . . . . . . . . . . . . . . . . . . . . . . . 1F2-3
Special Tools Table . . . . . . . . . . . . . . . . . . . . 1F2-3
Schematic and Routing Diagrams . . . . . . . 1F2-4
E23 ECU (MSE) . . . . . . . . . . . . . . . . . . . . . . 1F2-4
E23 ECU (HFM) . . . . . . . . . . . . . . . . . . . . . . 1F2-5
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . 1F2-6
Self Diagnosis Socket Pin Numbers and
Descriptions . . . . . . . . . . . . . . . . . . . . . . . . 1F2-6
Self Diagnosis Failure Code (for E23 ENG) . 1F2-7
Test Box Connection . . . . . . . . . . . . . . . . . . 1F2-10
Fuel Injection System Test . . . . . . . . . . . . . 1F2-11
Ignition System Test . . . . . . . . . . . . . . . . . . 1F2-20
Idling Control and Electronic Pedal
System Test . . . . . . . . . . . . . . . . . . . . . . . 1F2-25
Air Conditioner Control System Test . . . . . . 1F2-27
Fuel Pressure and Internal Leakage Test . . 1F2-28
Fuel Pump Test . . . . . . . . . . . . . . . . . . . . . . 1F2-30Injector Test . . . . . . . . . . . . . . . . . . . . . . . . 1F2-32
Maintenance and Repair . . . . . . . . . . . . . 1F2-34
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . 1F2-34
ECU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F2-34
Fuel Pressure Regulator . . . . . . . . . . . . . . 1F2-45
Fuel Distributor . . . . . . . . . . . . . . . . . . . . . . 1F2-49
Injector . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F2-54
Fuel Filter . . . . . . . . . . . . . . . . . . . . . . . . . . 1F2-57
Fuel Pump . . . . . . . . . . . . . . . . . . . . . . . . . 1F2-58
Purge Switchover Valve . . . . . . . . . . . . . . . 1F2-62
Vacuum System . . . . . . . . . . . . . . . . . . . . . 1F2-64
Crankshaft Position Sensor . . . . . . . . . . . . 1F2-66
Camshaft Position Sensor . . . . . . . . . . . . . 1F2-68
Hot Film Air Mass (HFM) Sensor . . . . . . . . . 1F2-70
Oxygen Sensor . . . . . . . . . . . . . . . . . . . . . . 1F2-73
Knock Sensor . . . . . . . . . . . . . . . . . . . . . . . 1F2-75
Coolant Temperature Sensor . . . . . . . . . . . 1F2-76
Accelerator Pedal Module . . . . . . . . . . . . . . 1F2-79

1F2-2 M161 ENGINE CONTROLS
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
Application
Fuel Return and Supply Line
Fuel Distributor Assembly Bolt
Pressure Test Connector
Fuel Inlet and Outlet Line
Fuel Filter Mounting Bracket Bolt
Crankshaft Position Sensor Bolt
Camkshaft Position Sensor Bolt
Knock Sensor Mounting Bolt
Coolant Temperature BoltN·m
25 - 30
22.5 - 27.5
21.6 - 26.4
25 - 30
4 - 8
9 - 11
9 - 11
22.5 - 27.5
18 - 22

M161 ENGINE CONTROLS 1F2-7
No ignition voltage output(NO.1 ignition coil;
1, 4cylinder)
No ignition voltage output(NO.2 ignition coil;
2, 3cylinder)
Cranshaft position sensor adaption failure
Start signal recognition failure
No.1 injector short(PWR)
No.1 injector open/short(GND)
No.2 injector short(PWR)
No.2 injector open/short(GND)
No.3 injector short(PWR)
No.3 injector open/short(GND)
No.4 injector short(PWR)
No.4 injector open/short(GND)
High oxygen sensor voltage
Low oxygen sensor amplifying voltage
Oxygen sensor operating failure
Not excessive lean indication in oxygen
sensor(during coasting)
Oxygen sensor heater short(power)
Oxygen sensor heater open/short(GND)
Low oxygen sensor voltage
Short learning control failure
Lambda control failure (rich stop)
Lambda control failure (lean stop)
Lambda idle adaptation failure(above rich
threshold)
Lambda idle adaptation failure(below lean
threshold)
learning control failure(rich, low load) Coolant temperature sensor open
Coolant temperature sensor short
Coolant temperature sensor signal failure
Intake temperature sensor open
Intake temperature sensor short
Intake temperature sensor signal failure
Low battery voltage
HFM sensor signal failure
HFM sensor signal failure (Low)
HFM sensor signal failure (High)
Crankshaft position sensor signal failure
(no engine revolution signal)
Crankshaft position sensor signal failure
(rpm > max. value)
No.1 cylinder recognition failure
Crankshaft position sensor signal failure
(gab recognition failure)
Transmission coding failure
Transponder signal communication failure
CAN communication failure : TCU(A/T only)
CAN communication failure :
communication initialization failure
Fuel pump relay short(PWR)
Fuel pump relay open/short(GND)
Purge valve short
Purge valve open/short
Condenser fan(HI) relay short(PWR)
Condenser fan(HI) relay short(GND)
No.1 knock sensor signal failure
No.1 cylinder synchronization failure 00
01
02
03
04
05
08
09
10
11
17
18
19
20
21
25
26
31
34
35
40
41
44
45
56
58
Failure
codeDescriptionFailure
codeDescription
64
65
67
71
72
73
74
75
76
77
78
79
80
81
82
83
86
87
89
93
96
97
98
99
100
SELF DIAGNOSIS FAILURE CODE (FOR E23 ENG)

1F2-12 M161 ENGINE CONTROLS
Failure
codeItem
09,
10,
11,
Checking method Te s t
stepRequirementSpecified
valuePossible cause
Þ 4.0· ·· ·
· HFM sensor
signal
105 81· Ignition:ON0.9 - 1.1V· Þ 4.1 - 4.3
· Cable
· External air inflow
· HFM sensor
· Engine:in Idle
(Coolant temperature
: > 70°C )1.3 - 1.7V
Þ 4.1
105 4
· Ignition:ON
· HFM sensor
connector removed4.7 - 5.2V
· Cable
· ECU coupling
· ·· ·
· HFM sensor:
- 5V power
supplyHFM
sensor
Þ 4.2
3 108· Ignition:ON
· HFM sensor
connector removed4.7 - 5.2V
· Þ 4.3
· Cable
· ·· ·
· HFM sensor:
- 5V power
supplyHFM
sensor
Þ 4.3
104 2· Ignition:ON
· HFM sensor
connector removed11 - 14V
· Cable
· OVPR
· ·· ·
· HFM sensor:
- 12V power
supplyHFM
sensor
03,
04,
05,Þ 5.0· ·· ·
· Intake air
temperature
sensor:
- Voltage105 80· Ignition:ON· Þ 5.1
· ECU
Þ 5.1· Ignition:OFF
· No.2 ECU coupling
removed 105 80
· Cable
· HFM sensor
· ·· ·
· Intake air
temperature
sensor:
- Resistance
: voltage value
is increased
when engine
rpm is
increased
± 5%
°C
10
20
30
40
50
60
± 5%W
3600
2420
1662
1166
853
600 °C
10
20
30
40
50
60V
3.1
2.65
2.18
1.76
1.4
1.1

M161 ENGINE CONTROLS 1F2-13
Failure
codeItemChecking method Te s t
stepRequirement
Specified
valuePossible cause
Þ 6.1· Ignition:ON0.1 - 0.3A· Cable
· Fuel pump relay
· ECU
· ·· ·
· Fuel pump
relay:
- Current
consumption
00,
01,
02,
06,Þ 7.0· ·· ·
· Coolant
temperature
sensor:
- Voltage79 78· Ignition:ON°CV
20 3.57
80 1.22
100 0.78· Þ 7.1
· ECU
± 5% Þ 6.0
· Ignition:ON
(Fuel pump relay will
operate for 1 - 2
seconds when the
ignition switch is
turned to "ON" after
stopping the
engine)
· Engine:cranking 33 11
· Cable
· Fuel pump relay
· ECU
· ·· ·
· Fuel pump
relay:
- Operation34,
35,11 - 14V
(approx.1-
2sec.)
11 - 14V
(Cranking or
driving)
533
Þ 7.1· Ignition:OFF
(Remove the No.2
coupling from ECU) 79 78· Þ 7.2
· cable
· ·· ·
· Coolant
temperature
sensor:
- Resistance
& cable°CW
20 2500
80 322
100 185
± 5%
Þ 7.2· ·· ·
· Coolant
temperature
sensor:
- ResistanceCoolant temperature
sensor:
14
· Remove the
connector from
coolant temperature
sensor and measure
the resistance
between No.1 and
No.2 pin with
multimeter.· Þ refer to
specified
resistance
value of 7.1.· Coolant
temperature
sensor

1F2-14 M161 ENGINE CONTROLS
Failure
codeItemChecking method Test
stepRequirementSpecified
valuePossible cause
Þ 9.0· Keep the engine run
above 2 minutes in
over 80°C of coolant
temperature6.0 - 7.0 V· ECU
· Cable
· Oxygen sensor
· ·· ·
· Oxygen
sensor:
- Signal80,
81,
82,
83,
89,560
Þ 8.0· Engine:in cranking
or idle
560· Cable
· ECU
· ·· ·
· ECU:
- RPM signal
output32,
33,refer to figure
2
Þ 10.0· Keep the engine run
above 2 minutes in
over 80°C of coolant
temperature.· ·· ·
· Oxygen
sensor:
- Heating
function
operated
Þ 11.0· ·· ·
· No.1
cylinder
injector:
- Operating &
injection
time· When the coolant
temperature is
approx. 20°C:
- Engine:in cranking8.0 ms· Cable
· ECU
· No.1 Injector
· Coolant
temperature sensor
· Oxygen sensor
· Intake air
temperature sensor
- Voltage· Engine:in cranking
or idle
(above 5V in idling)
16 17
59
911
· Ignition:ON11 - 14 V
· ECU
· Cable
· Oxygen sensor
- Current
consumption0.2 - 2.0 A
72,
73,
63 11
· When the coolant
temperature is
approx. 80°C:
- Engine:at idling
speed
- Engine:at sharp
acceleration(full
throttle)
(refer to figure 3
and 4)approx.
2.7 - 5.0ms
approx.14ms There will be a
voltage
fluctuation in
the range of
- 0.2 -1.0V.
85,
86,
87,