lock SSANGYONG MUSSO 1998 Workshop Repair Manual

REAR DRIVE AXLE 3D-17
Inspection
lRemove the LSD assembly and check the pre-load torque.
lIf necessary, replace LSD assembly.
Procedure
1. Fix the right shaft of LSD to the special tool (A).
2. Install the special tool (B) to the left shaft and rotate
counterclockwise and check the pre-load torque.
Normal Torque 3.6 - 9.0kgm
Notice
If necessary, replace LSD assembly.

SECTION 4A
HYDRAULIC BRAKES
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 4A-1
General Specifications . . . . . . . . . . . . . . . . . . 4A-1
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . 4A-2
Noise or Vehicle Vibration When Applied
Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4A-2
Pulls to One Side When Braking . . . . . . . . . . . 4A-2
Poor Braking . . . . . . . . . . . . . . . . . . . . . . . . . . 4A-2
Increasing Pedal Stroke (Pedal Goes to
Floor) or Brake Dragging . . . . . . . . . . . . . . . 4A-3
Poor Braking of Parking Brake . . . . . . . . . . . . 4A-3
TABLE OF CONTENTS
Component Locator . . . . . . . . . . . . . . . . . . . 4A-4
ABS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4A-4
ABS / ABD . . . . . . . . . . . . . . . . . . . . . . . . . . . 4A-5
Non-ABS / ABD . . . . . . . . . . . . . . . . . . . . . . . . 4A-6
Maintenance and Repair . . . . . . . . . . . . . . . 4A-7
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 4A-7
Bleeding the Brakes . . . . . . . . . . . . . . . . . . . . 4A-7
Brake Pedal . . . . . . . . . . . . . . . . . . . . . . . . . . 4A-9
LCRV (Load Conscious Reducing Valve) . . . 4A-12
Caution: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this
cable will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK
unless otherwise noted.
Type
Pedal Ratio
Pedal Stroke
Pedal Freeplay
Type
Inner Diameter
Type
Ratio
Type
I.D. of Caliper Cylinder
Thickness of Brake Pad
Thickness of Disc Plate
Type
I.D. of Caliper Cylinder
Thickness of Brake Pad
Thickness of Disc Plate
Type
Operation
SpecificationPBR Brake
4.3 : 1
132 mm
f23.81 mm
5.0 : 1
f60.4 mm
¬
f40.5 mm
9.5 mm
¬ Suspended
1 - 4 mm
Tandem Type with Lever Sensor
Vacuum Booster Type
Ventilated Disc
10 mm
24 mm
Rear Wheel Internal Expansion Type
Mechanical
SAE J1703, DOT3
SPECIFICATIONS
GENERAL SPECIFICATIONS
Brake Pedal
Master Cylinder
Brake Booster
Front Brake
Rear Brake
Parking Brake
Brake FluidMANDO Brake
4.3 : 1
138 mm
f25.4 mm
5.6 : 1
f60 mm
Solid Disc
f38.2 mm
10.0 mm
10.4 mm
Application

HYDRAULIC BRAKES 4A-11
Adjustment Procedure
1. Pedal Height
Notice
If pedal height is not in specified value, loosen the stop
lamp nut (B) and adjust the pedal height.
2. Pedal Stroke
Height (A) 150 mm (From the carpet)
Notice
If pedal stroke is not in specified value, loosen the stop bolt
and lock nut (F) and adjust the pedal stroke.
3. Free Play
Stroke (C)Mando : 138 mm
PBR : 132mm
Notice
To adjust, depress the brake pedal several times until there
is no more vacuum left in the vacuum line.
To adjust, loosen the lock nut (D) of the push rod and turn
the rod.
Free Play (E)1 - 4 mm
Inspection Procedure
1. Inspect the wear of bushing.
2. Inspect the warp and bend of brake pedal.
3. Inspect the return spring of brake pedal.
4. Inspect the conductivity when connecting the tester to the
stop lamp switch connector.

HYDRAULIC BRAKES 4A-13
Construction
LCRV consists of sensing part and hydraulic control part.
1. Sensing Part
It detects the changes of vehicle height caused by vehicle
load. It consists of load sensing spring and control lever
which change according to vehicle load.
2. Hydraulic Control Part
It consists of valve stem devices which controls hydraulic
pressure according to load detected by sensing part.
Trouble Shooting
Poor Braking
Possible Cause
Air in Brake System
Poor Adjustment of Sensor Spring
Damaged Sensor Spring
Fluid Leaking from LCRVRemedy
Bleeding
Adjust
Replace
Replace
Possible Cause
Poor Adjustment of Sensor Spring
Internal Fluid Leaking of LCRVRemedy
Adjust
Replace
Abnormal Locking

4A-14 HYDRAULIC BRAKES
LCRV SETTING METHOD
1. LCRV setting should be performed with unladen vehicle
condition.
2. Install the connecting rod (a) to the No.1 hole.
Tightening Torque14 - 18 Nm
3. Adjust the clearance “X” to be 0 mm and tighten the bolt (c)
using the lock nut (b).
Tightening Torque 14 - 18 Nm
4. Remove the connecting rod (a) from the No.1 hole and
reinstall it to the No. 2 hole.
5. Place alignment marks between the lock nut (b) and
adjusting screw (c) after the valve setting.

Front
Rear
Front
Rear
SECTION 4F
ANTILOCK BRAKE SYSTEM
TABLE OF CONTENTS
Caution: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this
cable will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK
unless otherwise noted.
SPECIFICATIONS
GENERAL SPECIFICATIONS
Application
Model
ECUNumber of Pins
Operating Temperature
Motor Operating Current
Solenoid Coil Resistance
External Resistance
Air Gap
Number of teethDescription
ABS 5.3
31
-40 ~ +120°C
Below MAX 40A
1.28KW - 1.92KW
0.35 - 1.60 mm
0.15 - 1.20 mm
52
52ABS/ABD 5.3
83
-40 ~ +85°C
Below MAX 45A
8.04 - 9.04W except AV,
HSV 4.04 - 4.54W
1.28KW - 1.92KW
0.35 - 1.60 mm
0.15 - 1.20 mm
52
52 Hydraulic System
Wheel Speed Sensor
Impulse Ring
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 4F-1
General Specifications . . . . . . . . . . . . . . . . . . 4F-1
Schematic and Routing Diagrams . . . . . . . . 4F-2
ABS 5.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4F-2
ABS/ABD 5.0 . . . . . . . . . . . . . . . . . . . . . . . . . 4F-3
ABS 5.3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4F-4
ABS/ABD 5.3 . . . . . . . . . . . . . . . . . . . . . . . . . 4F-5
Component Locator . . . . . . . . . . . . . . . . . . . 4F-6
ABS, ABS/ABD . . . . . . . . . . . . . . . . . . . . . . . . 4F-6
ABD System Description . . . . . . . . . . . . . . . 4F-7Self Diagnosis . . . . . . . . . . . . . . . . . . . . . . . 4F-9
ABS, ABS/ABD 5.3 . . . . . . . . . . . . . . . . . . . . . 4F-9
ABS, ABS/ABD 5.0 . . . . . . . . . . . . . . . . . . . . 4F-11
Defect Codes . . . . . . . . . . . . . . . . . . . . . . . . 4F-13
Maintenance and Repair . . . . . . . . . . . . . . 4F-19
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . 4F-19
Wheel Speed Sensor . . . . . . . . . . . . . . . . . . 4F-19
Hydraulic Circuit . . . . . . . . . . . . . . . . . . . . 4F-21
ABS 5.3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4F-21
ABS/ABD 5.3 . . . . . . . . . . . . . . . . . . . . . . . . 4F-24

4F-2 ANTILOCK BRAKE SYSTEM
ABS 5.0
SCHEMATIC AND ROUTING DIAGRAMS
5.0W
5.0W
30A
30A ENG

ANTILOCK BRAKE SYSTEM 4F-3
ABS/ABD 5.0
ABD ACTIVE

4F-4 ANTILOCK BRAKE SYSTEM
ABS 5.3
5.0W
5.0W
30A
30A
NO.21
K2

ANTILOCK BRAKE SYSTEM 4F-5
ABS/ABD 5.3
5.0W
5.0W