ECU SSANGYONG MUSSO 1998 Workshop User Guide

M162 ENGINE ELECTRICAL 1E1-11
Circuit Diagram
Inspection & Maintenance Procedure (for MSE)
1. While the ignition switch is in 'OFF' position, remove the
wiring connectors (1 and 15) from ignition coil and measure
the primary resistance between terminal No.1 and No.15.
2. During engine cranking, measure primary voltage (T1/1)
between ECU terminal No. 71 and No. 69. Notice
If out of specified value, replace the ignition coil.
Specified Value 0.9 - 1.6 W (20°C)
Specified Value 200 - 350 V
Notice
lMeasure remaining cables.
- T1/2 : No. 72 and 69.
- T1/3 : No. 70 and 69.
lIf out of specified value, check ignition cable and ECU.
3. Using a multi-tester, measure the secondary coil resistance
between 5a and 5b.
Specified Value 6 - 8.5 kW

M161 ENGINE ELECTRICAL 1E2-11
Inspection & Maintenance (for E2.3 MSE)
1. Measure the primary resistance between the cable terminals
1 and 15 after removing the ignition cable wiring connector
(1 and 15) with ignition switch OFF.
Notice
Replace the ignition coil if out of the specified resistance.
lT1/2 : between No.71 and No.69
Notice
Check the ignition cable and the ECU if out of the
specified value.
3. Measure the secondary cable resistance between the
ignition coil 5a and 5b using a multimeter. 2. Measure the primary voltage(T1/1) between the ECU
terminals No.72 and No.69 during the engine cranking
(starter motor activated).
Specified Value 6 - 8.5 KW
Specified Value 0.9 - 1.6 W
Specified Value 200 - 350 V

SECTION 1F1
M162 ENGINE CONTROLS
TABLE OF CONTENTS
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise
noted.
Specifications . . . . . . . . . . . . . . . . . . . . . . . 1F1-2
Fastener Tightening Specifications . . . . . . . . 1F1-2
Special Tools . . . . . . . . . . . . . . . . . . . . . . . 1F1-3
Special Tools Table . . . . . . . . . . . . . . . . . . . . 1F1-3
Schematic and Routing Diagrams . . . . . . . 1F1-4
E32 ECU (HFM) . . . . . . . . . . . . . . . . . . . . . . 1F1-4
E32 ECU (MSE) . . . . . . . . . . . . . . . . . . . . . . 1F1-5
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . 1F1-6
Self Diagnosis Socket Pin Numbers and
Descriptions . . . . . . . . . . . . . . . . . . . . . . . . 1F1-6
Self Diagnosis Failure Code . . . . . . . . . . . . . 1F1-7
Test Box Connection . . . . . . . . . . . . . . . . . . 1F1-10
Fuel Injection System Test (MSE3.62) . . . . . 1F1-11
Ignition System Test . . . . . . . . . . . . . . . . . . 1F1-21
Idling Control and Electronic Pedal
System Test . . . . . . . . . . . . . . . . . . . . . . . 1F1-26
Air Conditioner Control System Test . . . . . . 1F1-28
Fuel Pressure and Internal Leakage Test . . 1F1-29
Fuel Pump Test . . . . . . . . . . . . . . . . . . . . . . 1F1-31Injector Test . . . . . . . . . . . . . . . . . . . . . . . . 1F1-33
Maintenance and Repair . . . . . . . . . . . . . 1F1-35
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . 1F1-35
ECU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F1-35
Fuel Pressure Regulator . . . . . . . . . . . . . . 1F1-46
Fuel Distributor . . . . . . . . . . . . . . . . . . . . . . 1F1-50
Injector . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F1-54
Fuel Filter . . . . . . . . . . . . . . . . . . . . . . . . . . 1F1-57
Fuel Pump . . . . . . . . . . . . . . . . . . . . . . . . . 1F1-58
Purge Switchover Valve . . . . . . . . . . . . . . . 1F1-62
Vacuum System . . . . . . . . . . . . . . . . . . . . . 1F1-64
Crankshaft Position Sensor . . . . . . . . . . . . 1F1-65
Camshaft Position Sensor . . . . . . . . . . . . . 1F1-67
Hot Film Air Mass (HFM) Sensor . . . . . . . . . 1F1-69
Oxygen Sensor . . . . . . . . . . . . . . . . . . . . . . 1F1-72
Knock Sensor . . . . . . . . . . . . . . . . . . . . . . . 1F1-74
Coolant Temperature Sensor . . . . . . . . . . . 1F1-75
Accelerator Pedal Module . . . . . . . . . . . . . . 1F1-78

M162 ENGINE CONTROLS 1F1-3
SPECIAL TOOLS
SPECIAL TOOLS TABLE
129 589 00 21 00
Test Box
119 589 04 63 00
Pressure Hose
106 589 00 21 00
Pressure Tester
210 589 08 63 00
ECU Test Cable210201Adaptor line

1F1-4 M162 ENGINE CONTROLS
E32 ECU (HFM)
SCHEMATIC AND ROUTING DIAGRAMS

M162 ENGINE CONTROLS 1F1-5
E32 ECU (MSE)

1F1-6 M162 ENGINE CONTROLS
DIAGNOSIS
SELF DIAGNOSIS SOCKET PIN NUMBERS AND DESCRIPTIONS
1 Ground
2 Ignition 1
3 Battery Power Supply (Fuse NO.17)
4 REKES :PIN 6
5 Engine Speed Signal :MSE PIN 60
6 TCCU(Part-time)
7 STICS(PIN 26)
8-
9-
10 Air Bag(PIN 20)11 Remote Engine Start Unit(PIN 10)
12 -
13 Brake System
(ABS 5.3:PIN 11, ABS/ABD 5.3:PIN 46)
14 MSE 3.62S/3.53S(ECU Data Output:PIN 58)
15 TOD(PIN 20)
1 6 Immobilizer
17 -
1 8 TCU(PIN 23)
19 -
2 0 K-LINE(ECS:PIN 23)

1F1-8 M162 ENGINE CONTROLS
Cruise control acceleration failure
Cruise control deceleration failure
ECU failure(RAM)
ECU failure(EPROM)
Servo motor control output inter-ruption
memory failure
Servo motor open/short
Unprogramed ECU with Immobilizer
Uncoded ECU
ECU failure(NVRAM checksum failure)
ECU failure(coding ID checksum failure)
ECU failure(coding checksum failure)
ECU failure(programing checkusm failure)
ABD input signal short(power)
ABD input signal short(GND)
Low pedal valve sensor SP1 voltage
High pedal valve sensor SP1 voltage
Low pedal valve sensor SP2 voltage
High pedal valve sensor SP2 voltage
Different pedal valve sensor signal(1,2)
Pedal valve sensor 1,2 failure
HFM sensor, and throttle position sensor
failure
ECU failure(incompatible CPU)
ECU failure(CPUs communication failure)
ECU failure(CPU(2) configuration failure)
ECU failure(CPU(2) fault)
ECU failure(CPU run time failure between
CPUs)
No.5 injector short(PWR) 93
96
97
98
99
100
101
102
103
104
105
108
109
11 0
11 6
11 7
11 9
120
121
122
123
125
126
127
129
130
131
132Short learning control failure
Lambda control failure (rich stop)
Lambda control failure (lean stop)
Lambda idle adaptation failure(above rich
threshold)
Lambda idle adaptation failure(below lean
threshold)
learning control failure(rich, low load)
learning control failure(lean, low load)
learning control failure(rich, high load)
learning control failure(lean, high load)
Low throttle position sensor(IP1) voltage
High throttle position sensor(IP1) voltage
Low throttle position sensor(IP2) voltage
High throttle position sensor(IP2) voltage
Throttle actuator learning data fault
Throttle actuator learning control failure
Exceed fuel-cut safety time
Throttle valve return spring failure
Cruise control interruption memory failure
Throttle actuator failure
Pedal module position sensor signal failure
Different HFM signal with throttle potentiometer
Both throttle potentiometer(IP1&IP2) failure
IPS1 with IPS2
High permanent throttle signal
Message counter failure® cruise control ’OFF’
Vehicle speed signal failure
Vehicle speed signal failure
Cruise control lever failure133
134
136
137
139
140
141
142
143
144
145
146
150
151
160
161
162
163
164
167
185
186
187
188
189
190
192
Failure
codeDescriptionFailure
codeDescription

1F1-10 M162 ENGINE CONTROLS
TEST BOX CONNECTION
1 ECU
2 Test Coupling(No.1 - 60)
3 Test Coupling(No.61 - 120)
4 Multi-tester0 1 Test Box
02 ECU Test Cable
Tools Required
129 589 00 21 00 Test Box
210 589 08 63 00 ECU Test Cable

M162 ENGINE CONTROLS 1F1-11
FUEL INJECTION SYSTEM TEST (MSE3.62)
Failure
codeItem
Þ 1.0
Checking method
· Ignition:ON
Test
stepRequirementSpecified
valuePossible cause
10 1211 -14V
· ·· ·
· ECU:power
supply
- terminal
30(TM.30)
Þ 2.2· ·· ·
· Power
supply:
- terminal
87(TM.87)· Ignition:ON· Power supply cable
· OVPR 08,
·Þ 1.1
·Þ 1.2
Þ 1.1
· Ignition:ON
10 211 -14V· ·· ·
· Ground
cable:
- Battery
ground· Ground cable
· Ground conditionDiagnosis
socket
69 2
Diagnosis
socket
Þ 1.2· Ignition:ON
11211 -14V· ·· ·
· Power
supply:
- terminal
30(TM.30)· Power supply cable
Diagnosis
socket
Þ 2.0· Ignition:ON
51111 -14V· ·· ·
· ECU:power
supply
- terminal
87(TM.87)08,·Þ 1.1
·Þ 2.1
Þ 2.1
· Ignition:ON 11 -14V· ·· ·
· Ground
cable
- Electronic
ground· Ground cable
52
Diagnosis
socket
111
Diagnosis
socket· Ignition:OFF
11 -14V
< 1V
Þ 3.0
· Engine:in Cranking
52· Cable
· Ignition switch 11 -14
(during engine
cranking)
· ·· ·
· Start signal:
- terminal
50(TM.50)