weight SSANGYONG MUSSO 1998 Workshop User Guide

2E-4 TIRES AND WHEELS
COMPONENT LOCATOR
WHEEL AND TIRE
1 Wheel Bolts.................Steel Wheel : 80-120 Nm
..........................Aluminium Wheel : 110-130 Nm
2 Steel Wheel
3 Aluminium Wheel4 Tire
5 Steel Wheel Weight Balance
6 Hub Cap

2E-6 TIRES AND WHEELS
4. Tire pressure inspection.
lTire pressure.
lCheck tread contact with road.
Notice
lIf underinflated, tire may come away from the wheel
during rapid steering.
lAn overinflated tire will cause a hard riding and uneven
wear.
Front & Rear
(P235/75R15)2.1kg/cm (30PSI)2
5. Wheel balance.
lBalance weights should be on each side. When the wheel
is out of balance or a tire has been repaired, be sure to
balance the wheel again.
lIf total weight is over 150g, readjust the balance by
reinstalling the tire on the wheel.
lBalance weight should not protrude from the wheel rim
over 3mm.
lFor aluminum wheel, use aluminum wheel balance weight
only.

TIRES AND WHEELS 2E-7
lTo correct unbalance, install equal weights 180° opposite
each other, one on the inside of the wheel and one on
the outside, at the point of unbalance.
lBalance Weight
6. Cautions for installation and removal.
lClean the mounting surfaces of hub and wheel.
lDo not apply grease or oil on the nuts and bolts (It will
cause looseness and poor tightening).
lUsing a jack, lift up the tire about 3cm from the ground.
lTighten nuts in a criss-cross pattern 2-3 times.
10g
0.4oz20g
0.7oz30g
1.10oz40g
1.40oz50g
1.80oz60g
2.1oz
Steel : 80 - 120Nm
Aluminium : 110 - 130NmTighten Torque

PROPELLER SHAFT 3C-7
Installation Procedure
Clean the disassembled parts and replace them if damaged.
1. Align the alignment marks of the yoke and assemble the
spider, bearing and snap ring.
2. Apply grease to the inner of the bearing cap of the needle
roller bearing and assemble the needle roller.
Grease EP #2
6. Possible cause of vibration.
lDrift away of balance weights.
lExcessive runout of the propeller shaft.
lUsing normal bolts.
lExcessive wear of the universal joint.
lSticks in sleeve joint.
lDrive angle changes in universal joints or cross causes
vibration and can be detected around 60~100 km/h. 5. Universal joint starting torque.
Starting Torque 3 - 8 kglcm

AUTOMATIC TRANSMISSION 5A-105
21. Holding the cylinder horizontal, install the sleeve and clutch
plate assembly into the cylinder, with the crest of one wave
of the washer In line with one of the holes in the outside of
the cylinder, until the sleeve contacts the C2 wave washer.
22. Check the C4 clutch pack clearance using special tool No.
0555-331900. Refer to figure 8.25.
Notice
With the C2 wave spring compressed, and the clutch Pack
supporting a 2 k9 weight, the dimension from the underside
of the C2 pressure plate to the selective steel is to be
between 1.4- 1.8 mm. If the clutch is to be gauged from
the top of the pressure plate, then the dimension is to be
the actual thickness of the pressure plate plus 1.4-1.8 mm.
23. Use selective plates to achieve the correct specification. If
new friction plates are being fitted, remove the clutch pack
and soak the friction plates in ATF for a minimum of 5
minutes prior to reassembly.
Notice
The clutch pack clearance must be taken before the
elements are soaked in Automatic Transmission Fluid
(ATF).
24. Reassemble the sleeve and clutch pack into the cylinder.
Observe the alignment of the wave washer to the hole in
the cylinder.
25. Install the C2 clutch plates in the cylinder in the following
sequence:
lFriction disc
lSteel plate
lFriction disc
lSteel plate
lSteel plate - 0574-000001, 0574-000003,
0574-000004, 0574-000005, 0574-000020,
0574-000021, or friction disc -0574-000002
lSteel plate (selective)
lFriction disc
lSteel plate (selective)
lFriction disc

5A-106 AUTOMATIC TRANSMISSION
29. Align the tangs and fit the nylon thrust washer onto the
C4 hub. Refer to figure 8.27.
30. Align and fit the C4 hub to the C2 clutch and the OWC
assembly.
31. Check the rotation of the C2 hub. While holding the
C4 hub, the C2 hub should rotate in the clockwise
direction and lockup in the anti-clockwise direction when
viewed from the C2 hub. Refer to figure 8.27.
Figure 8.27 - C2 - Hub Rotation
32. Apply petroleum jelly to the No. 5 thrust bearing and fit
it to the C4 hub. Refer to figure 8.19.
33. Remove the C2 clutch plates from the clutch cylinder.
34. Fit the thrust plate over the cylinder inner hub. Refer
to figures 8.24 and 8.19.
35. Engage the C2/C4 clutch hub assembly in the C4 clutch
plates.
36. Install the C2 clutch plates.
37. Install the C3 hub and secure it with the circlip, ensuring
that the circlip is firmly seated in its groove.
Refer to figure 8.32.Figure 8.26 - Typical C2 Clutch Pack Clearance 26. Check the clutch pack clearance using only the weight
from tool No.0555-331900. Refer to figure 8.26.
Notice
With the clutch pack supporting a 2 kg weight, the
dimension from the C3 clutch hub locating step to the
friction plate is to be between 0.80-1.05 mm.
27. Use selective plates to achieve the correct specification.
If new friction plates are being fitted, remove the clutch
pack and soak the friction plates in ATF for a minimum
of 5 minutes prior to reassembly.
Notice
The clutch pack clearance must be taken before the
elements are soaked in ATF.
28. Lubricate and fit the 3-4 OWC and end caps to the C2
hub.

5A-108 AUTOMATIC TRANSMISSION
12. Install the circlip.
13. Check the C3 clutch clearance (refer to figure 8.29) using
special tool No.0555-331900 in the following manner
(weight only).
a. Place the weight on the pressure plate and measure
the distance from the end of the cylinder to the top of
the pressure plate.
b. Record this figure.
c. Remove the weight.
d. Lift the pressure plate up against the circlip and
measure the distance from the end of
the cylinder to the top of the pressure plate.
e. Record this figure.
f. Subtract the second reading from the first reading to
obtain the clutch pack clearance.
Notice
With the clutch pack supporting a weight of 2 kg, the
clearance between the snap ring and the top of the
pressure plate is to be between 1.20-1.45 mm.
14. If new friction plates are being fitted, remove the clutch
pack and soak the friction elements in automatic
transmission fluid for a minimum of five minutes prior to
reassembly.
Notice
The clutch pack clearance must be taken before the
elements are soaked in automatic transmission fluid.Figure 8.29 - Typical C3 Clutch Assembly
Clearance

5A-110 AUTOMATIC TRANSMISSION
C1 Clutch Overdrive Shaft and Input Shaft
Assembly
Notice
1. Ensure that the snap rings are fitted correctly.
2. Check pistons for cracks, especially the C1 piston.
3. Do not mix clutch piston return springs.
4. If the C1/C2 clutch packs separate from the C3 clutch pack,
make sure the No. 6 bearing doesn’t drop out of the bearing
retainer.
To assemble the C1 clutch overdrive shaft and input shaft
assembly, proceed as follows:
1. Check the overdrive shaft grooves for any defect.
2. Coat the sealing rings, large and small, with petroleum jelly
and fit them to the overdrive shaft. The sealing rings may
be held in place with a small amount of petroleum jelly.
3. Assemble the clutch plate and disc into the cylinder in the
following sequence:
lsteel plate
lfriction disc
lsteel plate
lfriction disc
lsteel plate
lsteel plate - 0574-GOOGOl, 0574-000003,
0574-000004, 0574-000005, 0574-000020,
0574-000021, or friction disc -0574-000002
lsteel plate (selective)
lfriction disc
lsteel plate (selective)
lfriction disc
4. Check the clutch pack clearance using special tool No.0555-
331900. Refer to figure 8.31.
Use selective plates to achieve the correct specification.
Notice
The clutch pack supporting a 2 kg weight, the dimension
from the input shaft locating stop to the friction disc must
be 0.70-0.90 mm.
5. If new friction plates are being fitted, remove the clutch pack
and soak the friction elements in automatic transmission
fluid for a minimum of five minutes prior to assembly.
Notice
The clutch pack clearance must be taken before
elements are soaked in automatic transmission fluid.
6. Check the fit of the C1 clutch hub on the overdrive shaft. If
it is loose, the hub and shaft assembly must be replaced.Figure 8.31 - Typical C1 Clutch Assembly
Clearance

Model
Type
Gear Ratio
Oil
Weight (Dry)
SECTION 5B
MANUAL TRANSMISSION
TABLE OF CONTENTS
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 5B-1
General Specifications . . . . . . . . . . . . . . . . . . 5B-1
Fastener Tightening Specifications . . . . . . . . . 5B-2
External View . . . . . . . . . . . . . . . . . . . . . . . . 5B-3
Gear Train . . . . . . . . . . . . . . . . . . . . . . . . . . 5B-3
Power Flow . . . . . . . . . . . . . . . . . . . . . . . . . 5B-4
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . 5B-5
Will not Shift (Control Lever Moves) . . . . . . . . 5B-5
Hard Shift or Control Lever Will not Move Into
Gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5B-5
Gears Crash When Shifting . . . . . . . . . . . . . . 5B-5
Transmission Jumps Out . . . . . . . . . . . . . . . . . 5B-6
Transmission Locked in One Gear . . . . . . . . . 5B-6
Transmission Noise . . . . . . . . . . . . . . . . . . . . . 5B-6
Transmission Leakage . . . . . . . . . . . . . . . . . . 5B-7Diagnosis Table . . . . . . . . . . . . . . . . . . . . . . . 5B-8
Component Locator . . . . . . . . . . . . . . . . . . . 5B-9
Maintenance and Repair . . . . . . . . . . . . . . 5B-11
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . 5B-11
Shift Control Cable . . . . . . . . . . . . . . . . . . . . 5B-11
Transmission . . . . . . . . . . . . . . . . . . . . . . . . 5B-14
Unit Repair . . . . . . . . . . . . . . . . . . . . . . . . . 5B-17
Major Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . 5B-17
Main Shaft . . . . . . . . . . . . . . . . . . . . . . . . . . 5B-27
Input Shaft . . . . . . . . . . . . . . . . . . . . . . . . . . 5B-32
Counter Shaft . . . . . . . . . . . . . . . . . . . . . . . . 5B-34
Extension Housing . . . . . . . . . . . . . . . . . . . . 5B-35
Shift Cover . . . . . . . . . . . . . . . . . . . . . . . . . . 5B-36
Inspection of Components . . . . . . . . . . . . . . 5B-40
Pre-Installation Checks . . . . . . . . . . . . . . . . . 5B-45
SPECIFICATIONS
GENERAL SPECIFICATIONS
Application
Description
T5WC
Floor Change
3.97 : 1
2.34 : 1
1.46 : 1
1.00 : 1
0.85 :1
3.71 : 1
ATF DEXRON II / III
3.4 L
Check : Every 15,000km, Replace : Every 50,000km
33kg 1st
2nd
3rd
4th
5th
Reverse
Specification
Capacity(litre)
Change Interval
Notice
Add LUBRIZOL (280cc) in oil after overhauling.

Model
Type
Gear Ratio
Oil
Manufacturer
WeightPart-Time 4408 (E)
E.S.O.F. Type
1 : 1
2.48 : 1
ATF S-3, S-4 or DEXRON II, III
1.2 L
Check : Every 15,000 km
Replace : Every 50,000 km
Borg Warner
30 kg
SECTION 5D1
TRANSFER CASE (PART TIME 4408)
TABLE OF CONTENTS
SPECIFICATIONS
GENERAL SPECIFICATIONS
Caution: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this
cable will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK
unless otherwise noted.
Specifications . . . . . . . . . . . . . . . . . . . . . . . 5D1-1
General Specifications . . . . . . . . . . . . . . . . . 5D1-1
Schematic and Routing Diagram . . . . . . . . 5D1-2
Part Time Transfer Case - 4408 . . . . . . . . . . 5D1-2
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . 5D1-3
Self-Diagnosis . . . . . . . . . . . . . . . . . . . . . . 5D1-4
System Description . . . . . . . . . . . . . . . . . . . . 5D1-4
Self-Diagnosis Test . . . . . . . . . . . . . . . . . . . . 5D1-8Diagnostic Diagram . . . . . . . . . . . . . . . . . . . 5D1-9
Maintenance and Repair . . . . . . . . . . . . . 5D1-10
On-Vehicle Service . . . . . . . . . . . . . . . . . . . 5D1-10
Maintenance of Transfer Case Lubricant . . 5D1-10
Transfer Case . . . . . . . . . . . . . . . . . . . . . . . 5D1-11
Unit Repair . . . . . . . . . . . . . . . . . . . . . . . . 5D1-14
Transfer Case . . . . . . . . . . . . . . . . . . . . . . . 5D1-14
Transfer Case Control Unit (TCCU) . . . . . . 5D1-36
High
Low
Specification
Capacity
Lubrication ApplicationDescription