diagram SSANGYONG MUSSO 1998 Workshop Repair Manual

GENERAL ENGINE INFORMATION 1A1-9
COMPRESSION PRESSURE TEST
1 Compression Pressure Tester
2 Diagram Sheet3 Adaptor
4 Sealing Cone
Tools Required
001 589 76 21 00 Compression Pressure Tester
119 589 01 09 00 Spark Plug Wrench
Standard Service Data
Compression Ratio
Normal Engine Temperature
Normal Compression Pressure
Permissible Pressure Difference Between Individual
Cylinders10 : 1
80°C
Min. 10 bar, Max. 14 bar
Min. 6 bar, Max. 10 bar
Max. 1.5 bar General
Fuel Optimization

1A1-10 GENERAL ENGINE INFORMATION
Measuring Procedure
1. Warm the engine up to normal operating temperature.
2. Remove the spark plugs.
3. Place the diagram sheet to compression pressure
tester.
4. Connect the adaptor to compression pressure tester
and install it into the spark plug hole.
5. Crank the engine approx. eight revolutions by using
the start motor.
6. Compare the measurements of compression
pressure tester with the specifications.
7. Measure the compression pressure of the other
cylinders in the same way.
8. If measured value is not within the specifications,
perform the cylinder pressure leakage test.
Notice
lDischarge the combustion residues in the cylinders
before testing the compression pressure.
lApply the parking brake before cranking the
engine.

1A2-10 GENERAL ENGINE INFORMATION
COMPRESSION PRESSURE TEST
1 Compression Pressure Tester
2 Diagram Sheet3 Adaptor
4 Sealing Cone
Tools Required
001 589 76 21 00 Compression Pressure Tester
119 589 01 09 00 Spark Plug Wrench
Standard Service Data
Compression Ratio
Normal Engine Temperature
Normal Compression Pressure
Permissible Pressure Difference Between Individual
Cylinders10.4, 9.6
80°C
Min. 11 bar, Max. 15 bar
Min. 10.5 bar, Max. 14 bar
Max. 1.5 bar E23 Engine(e = 10.4)
E20 Engine(e = 9.6)

GENERAL ENGINE INFORMATION 1A2-11
Measuring Procedure
1. Warm the engine up to normal operating temperature.
2. Remove the spark plugs.
3. Place the diagram sheet to compression pressure
tester.
4. Connect the adaptor to compression pressure tester
and install it into the spark plug hole.
5. Crank the engine approx. eight revolutions by using
the start motor.
6. Compare the measurements of compression
pressure tester with the specifications.
7. Measure the compression pressure of the other
cylinders in the same way.
8. If measured value is not within the specifications,
perform the cylinder pressure leakage test.
Notice
lDischarge the combustion residues in the cylinders
before testing the compression pressure.
lApply the parking brake before cranking the
engine.

M162 ENGINE ELECTRICAL 1E1-11
Circuit Diagram
Inspection & Maintenance Procedure (for MSE)
1. While the ignition switch is in 'OFF' position, remove the
wiring connectors (1 and 15) from ignition coil and measure
the primary resistance between terminal No.1 and No.15.
2. During engine cranking, measure primary voltage (T1/1)
between ECU terminal No. 71 and No. 69. Notice
If out of specified value, replace the ignition coil.
Specified Value 0.9 - 1.6 W (20°C)
Specified Value 200 - 350 V
Notice
lMeasure remaining cables.
- T1/2 : No. 72 and 69.
- T1/3 : No. 70 and 69.
lIf out of specified value, check ignition cable and ECU.
3. Using a multi-tester, measure the secondary coil resistance
between 5a and 5b.
Specified Value 6 - 8.5 kW

SECTION 1F1
M162 ENGINE CONTROLS
TABLE OF CONTENTS
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise
noted.
Specifications . . . . . . . . . . . . . . . . . . . . . . . 1F1-2
Fastener Tightening Specifications . . . . . . . . 1F1-2
Special Tools . . . . . . . . . . . . . . . . . . . . . . . 1F1-3
Special Tools Table . . . . . . . . . . . . . . . . . . . . 1F1-3
Schematic and Routing Diagrams . . . . . . . 1F1-4
E32 ECU (HFM) . . . . . . . . . . . . . . . . . . . . . . 1F1-4
E32 ECU (MSE) . . . . . . . . . . . . . . . . . . . . . . 1F1-5
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . 1F1-6
Self Diagnosis Socket Pin Numbers and
Descriptions . . . . . . . . . . . . . . . . . . . . . . . . 1F1-6
Self Diagnosis Failure Code . . . . . . . . . . . . . 1F1-7
Test Box Connection . . . . . . . . . . . . . . . . . . 1F1-10
Fuel Injection System Test (MSE3.62) . . . . . 1F1-11
Ignition System Test . . . . . . . . . . . . . . . . . . 1F1-21
Idling Control and Electronic Pedal
System Test . . . . . . . . . . . . . . . . . . . . . . . 1F1-26
Air Conditioner Control System Test . . . . . . 1F1-28
Fuel Pressure and Internal Leakage Test . . 1F1-29
Fuel Pump Test . . . . . . . . . . . . . . . . . . . . . . 1F1-31Injector Test . . . . . . . . . . . . . . . . . . . . . . . . 1F1-33
Maintenance and Repair . . . . . . . . . . . . . 1F1-35
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . 1F1-35
ECU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F1-35
Fuel Pressure Regulator . . . . . . . . . . . . . . 1F1-46
Fuel Distributor . . . . . . . . . . . . . . . . . . . . . . 1F1-50
Injector . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F1-54
Fuel Filter . . . . . . . . . . . . . . . . . . . . . . . . . . 1F1-57
Fuel Pump . . . . . . . . . . . . . . . . . . . . . . . . . 1F1-58
Purge Switchover Valve . . . . . . . . . . . . . . . 1F1-62
Vacuum System . . . . . . . . . . . . . . . . . . . . . 1F1-64
Crankshaft Position Sensor . . . . . . . . . . . . 1F1-65
Camshaft Position Sensor . . . . . . . . . . . . . 1F1-67
Hot Film Air Mass (HFM) Sensor . . . . . . . . . 1F1-69
Oxygen Sensor . . . . . . . . . . . . . . . . . . . . . . 1F1-72
Knock Sensor . . . . . . . . . . . . . . . . . . . . . . . 1F1-74
Coolant Temperature Sensor . . . . . . . . . . . 1F1-75
Accelerator Pedal Module . . . . . . . . . . . . . . 1F1-78

1F1-4 M162 ENGINE CONTROLS
E32 ECU (HFM)
SCHEMATIC AND ROUTING DIAGRAMS

M162 ENGINE CONTROLS 1F1-49
The pressure difference between the fuel pressure and
the intake manifold is approx. 3.2 bars during idling.

1. Fuel Pressure Regulator
2. Intake Manifold
3. Fuel Return(to fuel tank)
4. Fuel Supply(from fuel pump)
7. Fuel Pressure(approx. 3.2 bars)
8. Intake Manifold Negative Pressure(0.6 bars)
A. Fuel pressure
B. Intake Manifold Negative Pressure
LL. Idling
TL. Partial load
VL. Full load

1F1-70 M162 ENGINE CONTROLS
Circuit Diagram
1 Housing
2 Electronic Housing
3 Connector
R
H : Heat Resistance
R
T : Temperature Resistance
R
S : Sensor Resistance

M162 ENGINE CONTROLS 1F1-79
Accelerator Pedal Sensor Connector(Sensor Side)
Potentiometer 1.
Pin no. 3 :Red
Pin no. 1 :Yellow
Pin no. 5 :Brown
Potentiometer 2.
Pin no. 6 :Violet
Pin no. 4 :Green
Pin no. 2 :White
Accelerator Pedal Sensor Connector(Vehicle Side)
Potentiometer 1.
Pin no. 3 :Red-Black
Pin no. 1 :Blue-Green
Pin no. 5 :Yellow-Green
Potentiometer 2.
Pin no. 6 :Green
Pin no. 4 :Blue-Red
Pin no. 2 :LightGreen
Function
Potentiometer 1, Power Supply(+)
Potentiometer 1, Signal
Potentiometer 2, Ground
Potentiometer 2, Power Supply(+)
Pin no. 3
Pin no. 1
Pin no. 5
Pin no. 6
Pin no. 4
Pin no. 2Potentiometer 2, Signal
Potentiometer 2, Ground
Circuit Diagram
Potentiometer 1.
Potentiometer 2.