light SSANGYONG MUSSO 2003 User Guide

1E3-4 OM600 ENGINE ELECTRICAL
Preheating System Operation
1. Preheating before start.Preheating time is different by coolant temperature and it is on until the glow indicator light goes off.
2. Preheating after start. Preheating continues for max. 60 seconds to rise in characteristic of warming-up on engine after starting too.
3. Monitoring on glow plug. Glow plugs are monitored by low current by the microprocessor in control relay respectively while running theengine. If glow indicator comes on after starting for about one minute,
it indicates on or several plugs are faulty.
Possible Cause
- One or several glow are faulty
Problem
Glow indicator does not come on in preheating time and comes on after starting the engine. Glow indicator does not come on while preheating and after starting engine. Glow indicator does not come on and engine
’s
starting is difficult or does not start at all. Glow indicator comes on after starting for about one minute.1 2 3 4 - Faulty glow indicator
- Faulty circuit of glow indicator
- Faulty control relay
- Circuits short in one or several glow plugs
- Faulty preheating circuits
- Faulty control relay
- One or several glow plugs are faulty

1F1-38 M162 ENGINE CONTROLS
Pin No.Abbreciation
Decription
21 222324252627282930313233343536373839404142434445464748495051525354555657585960 BRS
-----
KLIKU ---
GND
SP1+5V KP
TEV ML -
CAN L
CAN H -- - -
KPI
KLIMAKLIMA -
SP1SSP2S BLS
GND
SP2+2.5V S+BWA
S-B
KSK -
AUS
DIAG
V-SIG
TN-SIG
Brake switch-----Air conditioning clutch relay---Pedal potentiometer 1 groundPedal potentiometer 1 supplyFuel pump relay
Tank purge valveEngine fan (H1)-CAN-LowCAN-High-- - -Clutch switchAir conditioningElectronic traction signal-Pedal potentiometer 1 signalPedal potentiometer 2 signalBrake light switchPedal potentiometer 2 groundPedal potentiometer 2 supplyCruise accelerate/SetCruise resumeCruise decelerate/SetCruise safety contact switch-Cruise off switchDiagnostics (k-line)
Vehicle speed signalEngine speed signal

1F1-42 M162 ENGINE CONTROLS
Pin No.Description
Pedal potentiometer 1 ground Pedal potentiometer 1 supplyFuel pump relay
Tank purge valve Engine fan -CAN-LowCAN-High - - --Clutch switchAir conditioning Electronic traction signal(ABD) -Pedal potentiometer 1 signalPedal potentiometer 2 signalBrake light switchPedal potentiometer 2 ground Pedal potentiometer 2 supply Cruise accelerate/SetCruise resumeCruise decelerate/SetCruise safety contact switch - Cruise off switchDiagnostics(K-line)
Vehicle speed signalEngine speed signal31 323334 35 363738 39 40 41424344 45 4647484950 51 52535455 56 57585960GND
SP1+5V KP
TEV ML
-
CAN L
CAN H
- - --
KPL
KLIMA ETS
-
SP1SSP2S BLS
GND
SP2+2.5V
S+BWA
S-B
KSK -
AUS
DIAG
V-SIG
TN-SIG




-

- - --


-







-







-

- - --


-







-


Remarks
Abbreviation E32 ENG,
5speed M/T
E32 ENG,
4speed A/T (BTRA)

M162 ENGINE CONTROLS 1F1-47
3. Disconnect the vacuum hose.
4. Disconnect the circlip and remove the fuel pressureregulator.
5. Apply the oil to O-ring lightly and then replace it.
6. Installation should follow the removal procedure in the reverse order.
7. Check for fuel pressure and internal leaks by operating the engine.
2. Discharge the pressure in fuel supply system by pressing
the service valve.
Removal & Installation Procedure
1. Remove the fuel pressure test connector.

M162 ENGINE CONTROLS 1F1-79
Accelerator Pedal Sensor Connector(Sensor Side)
Potentiometer 1.Pin no. 3 :Red
Pin no. 1 :YellowPin no. 5 :Brown
Potentiometer 2. Pin no. 6 :VioletPin no. 4 :GreenPin no. 2 :White
Accelerator Pedal Sensor Connector(Vehicle Side)
Potentiometer 1.Pin no. 3 :Red-Black Pin no. 1 :Blue-Green
Pin no. 5 :Yellow-Green
Potentiometer 2. Pin no. 6 :GreenPin no. 4 :Blue-RedPin no. 2 :LightGreen
Function Potentiometer 1, Power Supply(+)
Potentiometer 1, Signal
Potentiometer 2, Ground
Potentiometer 2, Power Supply(+)
Pin no. 3 Pin no. 1 Pin no. 5 Pin no. 6
Pin no. 4 Pin no. 2Potentiometer 2, SignalPotentiometer 2, Ground
Circuit Diagram
Potentiometer 1. Potentiometer 2.

1F3-38 OM600 ENGINE CONTROLS
Tools Required 617 589 08 21 00 Position Sensor
Test Procedure
1. Remove the screw plug (5) and seal (4) and collect oil in a suitable vessel.
2. Install the position sensor (1) into the governor housing of
the injection pump to be the guide pin of the position sensor facing up.
3. Connect the battery terminal of position sensor (1) to positive terminal (+) of battery.
Position Sensor 617 589 08 21 00
4. Rotate the crankshaft by hand (in direction of engine rotation) until the lamp ‘B’ lights up. Rotate the crankshaft carefully
further until both lamps ‘A and B ’ come on. In this position,
check the Rl value on the crankshaft vibration damper. Notice If only lamp ‘A’ lights up, repeat the test and if out of
specification, adjust start of delivery.
Specification A TDC 14° - 16 °

OM600 ENGINE CONTROLS 1F3-43
Tools Required 617 589 08 21 00 Position Sensor Adjustment Procedure
1. Position the No. 1 cylinder at ATDC 15°
Notice Do not rotate the engine in opposite direction of engine rotation.
2. Remove the bolt (2) at the supporting bracket.
3. Remove the bolt (4).
4. Turn the adjusting screw (1) until both lamps ‘A’ + ‘ B ’ on
the position sensor light up. Notice If the adjustment range is not adequate, remove the injection pump and reinstall.
Position Sensor 617 589 08 21 00
5. After adjusting, retighten all the bolt to the specified torque.
To the right
To the left Start of delivery retarded
Start of delivery advanced

WHEEL ALIGNMENT 2B-5
VIBRATION DIAGNOSIS Wheel imbalance causes most highway speed vibration problems. A vibration can remain after dynamicbalancing because:
A tire is out of round.
A rim is out of round.
A tire stiffness variation exists.
Measuring tire and wheel free runout will uncover only part of the problem, All three causes, known as loadedradial runout, must be checked using method of substituting known good tire and wheel assemblies on the problem vehicle. Preliminary Checks Prior to performing any work, always road test the car and perform a careful visual inspection for:

Obvious tire and wheel runout.
Obvious drive axle runout.
Improper tire inflation.
Incorrect trim height.
Bent or damaged wheels.
Debris build-up on the tire or the wheel.
Irregular or excessive tire wear.
Improper tire bead seating on the rim,
Imperfections in the tires, including: tread deformations, separations, or bulges from impactdamage. Slight sidewall indentations are normal and
will not affect ride quality.
Tire Balancing Balance is the easiest procedure to perform and should be done first if the vibration occurs at high speeds. Do an off-vehicle, two-plane dynamic balance first to correct
any imbalance in the tire and wheel assembly. An on-vehicle finish balance will correct any brake drum,
rotor, or wheel cover imbalance, If balancing does not correct the high-speed vibration, or if the vibration occurs at low speeds, runout is the probable cause.

PROPELLER SHAFT 3C-5
5. If difficult to remove, clamp the yoke side in a vise and tapoff the needle bearing, using a proper tool.
6. Disassemble the universal joint parts. As axles move up and down, universal joints allow drive angles to change without binding propeller shaft.
1 Grease Nipple
2 Flange Yoke
3 Spider4 Seal
5 Needle Roller Bearing
6 Snap Ring
4. Slightly tapping the yoke shoulder using a brass hammer,
remove the bearing. Remove the remaining bearings in the
same way.

POWER BOOSTER 4C-5
PEDAL STROKE INSPECTION
1. Start the engine and stop it after one or two minutes.Depress the brake pedal several times. If the pedal goes down furthest the first time, but gradually rises after the second or third time, brake booster is normal.If there is no change in pedal stroke, the brake booster is abnormal.
2. Depress the brake pedal several times with engine stopped, and depress the brake pedal and start the engine. If the
pedal goes down slightly, the booster is normal.
3. Depress the brake pedal with engine running, and stop it with the pedal depressed. If there is no change in pedalheight during 30 sec., the booster is normal.