engine SSANGYONG MUSSO 2003 Owner's Guide

1B1-2 M162 ENGINE MECHANICALSPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS N

 m
35 - 40 10 - 15 5 - 10
21 - 25 30
56 - 6650 - 60 10 - 15
41.5 - 49.522.5 - 27.522.5 - 27.5
9 - 11
9 - 11
22.5 - 27.5
9 - 11
22.5 - 27.5
10
+90 °
55
+90 °
+90 °
22.5 - 27.522.5 - 27.5 9 - 109 - 10200
+90 °
40
+90 °
45
+90 °
35
9 - 11 20
+90 °
20
+90 °
20 / + 90 °
20 / + 90 °
22.5 - 27.5
Application
Power Steering Hydraulic Lines A/C High Pressure and Liquid HoseRadiator Support Menber BoltFuel Supply and Return Hose to Fuel DistributorExhaust Manifold and Pipe
Propeller Shaft to Transmission Engine Mounting NutAlternator Carrier BoltBelt Pulley BoltSteering Pump Bolt A/C Bracket Bolt Intake Air Duct BoltIgnition Cable Cover BoltCylinder Head Cover BoltCamshaft Adjuster Bolt Cylinder Head Front Cover Bolt Flange Bolt in Exhaust Camshaft Sprocket Cylinder Head Bolt Cooling Fan Bracket Bolt
Timing Gear Case Cover Bolt M8 M6
Crankshaft Rear Cover BoltVibration Damper Center Bolt Connecting Rod Bearing Cap Bolt Flywheel Stretch Bolt Amarture Bolt in Flywheel Ring and Seal Cover Nut in FlywheelSprocket Bolt to Exhaust Camshaft Camshaft Adjuster Flange Bolt Intake Flange Shaft Bolt Exhaust Camshaft Sprocket Bolt Camshaft Bearing Cap Bolt

M162 ENGINE MECHANICAL 1B1-3
N

 m
20 / +90 °
40
72 - 88
20 / +90 °
25 - 35
22.5 - 27.5 22.5 - 27.5 22.5 - 27.5 22.5 - 27.5 30
26 - 34
30
8 - 10 2525
22.5 - 27.5 29 - 35
22.5 - 27.5 9 - 11
50
9 - 11
15Application
Exhaust Camshaft Sproket Bolt
Chain Tensioner Screw Plug
Chain Tensioner AssemblyExhaust Camshaft Sprocket to CamshaftOil Pump Sprocket Bolt
Tensioning Device Bolt
Water Pump PulleyUpper Intake Manifold BoltLower Intake Mainfold BoltFlange Bolt to Exhaust Mainfold Exhaust Mainfold Nut to Stud Bolt Rivet Nut in Exhuast Mainfold HolePre-silencer BoltOil Drain PlugOil Filter Cover Oil Filter Bolt Oil Pump Drive Sprocket BoltOil Pump Mounting BoltOil Strainer Bracket Bolt
Oil Pressure Relief Valve Screw Plug
Oil Dipstick Guide Tube Bolt Oil Gallery Screw Plug
FASTENER TIGHTENING SPECIFICATIONS (Co n t ’d)

1B1-4 M162 ENGINE MECHANICALSPECIAL TOOLS
SPECIAL TOOLS TABLE
001 589 66 21 00 Torque Wrench
000 589 01 10 00
Box Wrench Insert 124 589 15 21 00
Radiator CapTesting Unit
116 589 02 34 00
Screw-Fixed Pin
000 589 10 99 01 Torque Wrench
112 589 00 72 00 Oil Extractor 000 589 72 21 00
Torque Wrench
000 589 40 37 00
Hose Clamp

M162 ENGINE MECHANICAL 1B1-5
104 589 01 01 00Spanner
111 589 18 61 00Lever Pusher 111 589 25 63 00
Thrust Piece
SPECIAL TOOLS TABLE (Co n t
’d)
111 589 01 59 00
Supporting Bar
116 589 06 63 00
Magnetic Finger
119 589 00 43 00 Drift 000 589 58 43 00 Chain Assembly
104 589 00 37 00
Pliers

1B1-6 M162 ENGINE MECHANICAL116 589 20 33 00
Sliding Hammer
602 589 00 40 00 Engine Lock 103 589 00 33 00
Puller
SPECIAL TOOLS TABLE (Co n t
’d)
601 589 03 43 00
Sleeve
001 589 65 09 00
Socket Wrench Insert
001 589 74 21 00 Torque Wrench 000 589 04 14 00
Clamping Strap
000 589 88 33 00
Puller

M162 ENGINE MECHANICAL 1B1-7
103 589 01 63 00Rivet Set
103 589 02 09 00 Oil Filter
Socket Wrench 102 589 12 15 00
Drift
SPECIAL TOOLS TABLE (Co n t
’d)
615 589 01 33 00
Caulking Bolt
102 589 00 15 00 Drift
000 589 51 37 00 Clamping Strap 001 589 72 21 00
Torque Wrench
601 589 03 14 00
Sleeve

1B1-8 M162 ENGINE MECHANICALMAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
ENGINE ASSEMBLY
Tools Required
000 589 10 99 01 Torque Wrench
000 589 40 37 00 Hose Clamp
112 589 00 72 00 Oil Extractor

M162 ENGINE MECHANICAL 1B1-9
4. Disconnect the coupling of HFM sensor and remove the aircleaner cross pipe.
6. Loosen the radiator drain cock and drain the coolant. Notice Open the coolant reservoir cap.
5. Remove the air cleaner cover. Remove the mounting bolts
and air cleaner housing and element assembly.
Removal & Installation Procedure
1. Disconnect the negative terminal of battery.
2. Remove the hood.
3. Remove the under cover.
Installation Notice
Tightening Torque 28 - 47 Nm

1B1-10 M162 ENGINE MECHANICAL
10. Remove the upper mounting bolts of radiator and thenremove the radiator.
7. Loosen the cylinder block drain plug and then drain thecoolant completely. Installation Notice
Tightening Torque 30 Nm
Notice Replace the seal before installation of the drain plug.
8. Remove the cooling fan shroud.
9. Disconnect the each hose from radiator.

M162 ENGINE MECHANICAL 1B1-11
12. Discharge the refrigerant from A/C system, and disconnectthe discharge pipe and suction pipe from the compressor.
14. Remove the fuel feed and return line. Notice Before removing the fuel lines, release the pressure in the fuel system. Installation Notice
13. Remove the acceleration control cable and automatic
transmission pressure cable.
11. Remove the hydraulic pipe of power steering.
NoticeCompletely drain the oil.
Tightening Torque 21 - 25 Nm