warning SSANGYONG NEW ACTYON SPORTS 2012 User Guide

14-6
Excessive overload of CDPF (warning lamp illuminated)
If the vehicle is driven at a speed of 5 to 10 km/h for an extended period of time, the soot
accumulated in the CDPF cannot be burned as the CDPF cannot reach the regeneration
temperature. Then, an excessive amount of soot can be accumulated in the CDPF.
This case is much worse than the simple over-load of the CDPF. To inform this to the driver,
the engine warning lamp comes on and the engine power is decreased to protect the
system.
To solve this problem, blow soot between the engine and exhaust system several times and
erase the related DTC. Then, check if the same DTC is regenerated again. If so, check the
DTC related to the differential pressure sensor. 1.
2.
3.

01-10
(3) Turn signal lamp (Hazard warning lamp operation)
The B+ power supplied through the No. F66 interior fuse on the right-hand of the engine
compartment is on standby on the No. 30 and 86 hazard warning lamp relay terminals via the ICM
No. 18 terminal.
The STICS activates and/or controls the hazard warning lamp relay using the No. A26 terminal
depending on the operating conditions. The activated relay supplies the No. 87 and 87a terminals
with the power, which is on standby on the No. 30 hazard warning lamp relay terminal.
The supplied power flows to the corresponding circuit via the No. 7 and 16 ICM terminals.

02-38710-01
1. PERFORMANCE AND SPECIFICATIONS
1) Rated Load & Input Signals
Rated Load ▶
NO. Item Rated Load
1 Chime bell / Buzzer DC 12V 350 mA (Inductive load)
2 Front room lamp DC 12V 16W (Lamp load)
3 Rear room lamp DC 12V 8W (Lamp load)
4 Ignition key illumination DC 12V 1.2W (Lamp load)
5 Seat belt indicator DC 12V 1.2W (Lamp load)
6 Parking brake warning lamp DC 12V 1.2W (Lamp load)
7 Door ajar warning lamp DC 12V 1.2W (Lamp load)
8 Door lock relay DC 12V 200 mA (Inductive load)
9 Door unlock relay DC 12V 200 mA (Inductive load)
10 Horn relay DC 12V 260 mA
11 Tail lamp relay DC 12V 200 mA (Inductive load)
12 Hazard warning lamp relay DC 12V 200 mA (Inductive load)
13 Power window relay DC 12V 200 mA (Inductive load)
14 Rear defogger relay DC 12V 200 mA (Inductive load)
15 Wiper LOW relay DC 12V 200 mA (Inductive load)
16 Wiper HIGH relay DC 12V 200 mA (Inductive load)
17 Front washer motor DC 12V 1.5A
18 Head lamp relay DC 12V 750 mA (Inductive load)
19 Front defogger relay DC 12V 200 mA (Inductive load)
20 Mirror lock relay DC 12V 200 mA (Inductive load)
21 Mirror unlock relay DC 12V 200 mA (Inductive load)

02-238710-01
▶Ignition Key Reminder Warning
The chime buzzer sounds continuously when opening the driver's door while the ignition
key is in ignition switch.
When removing the ignition key or closing the driver's door during chime buzzer operation,
the buzzer stops.
This function does not work when the IGN1 switch is in "ON" position. -
-
- (The function has priority over the "TAILLAMP ON WARNING".)
Chime Buzzer
PAS buzzer
ICM relay box
STICS

02-26
▶Tail Lamp Left On Warning
The chime buzzer sounds with the interval of 0.8 second when opening the driver's door
while the tail lamp is turned on and the ignition key is removed.
The c/buzzer output stops when turning off the tail lamp and closing the driver's door.
The system outputs "UNLOCK" signal for 5 seconds when the driver's and passenger's door
lock switch is locked (while the tail lamp is turned on and the driver's door is open).
This function does not work when the IGN1 switch is in "ON" position. -
-
-
-

02-278710-01
▶Door Ajar Warning
The warning light comes on when opening any door while the vehicle speed is below 10
km/h.
The warning light goes off when closing the door under step (1).
The warning light blinks when the vehicle speed is over 10 km/h while the warning light is
turned on.
The warning light blinks when a door is open while the vehicle speed is over 10 km/h.
The warning light goes off when closing the door under step (3).
The warning light comes on when the vehicle speed goes below 10 km/h under step (3). 1.
2.
3.
4.
5.
6.
Since the luggage room tailgate does not have the door switch, the door ajar warning light
does not come on when it is open.

02-28
▶Seat Belt Warning
The seat belt warning light comes on and the chime buzzer sounds for 6 seconds when
turning the ignition key to "ON" from "OFF".
If the seat belt is fastened before turning the ignition key to the the "ON" position, the
warning light blinks, however, the chime buzzer does not sound.
The seat belt warning light goes off and the chime buzzer stops when turning the ignition
switch to the "OFF" position during the warning operation.
The chime buzzer stops and the seat belt warning light stays on for the remainig time when
fastening the seat belt.
The seat belt warning light comes on and the chime buzzer sounds for 6 seconds again
when unfastening the seat belt during fastening operation while the ignition key is "ON"
position. 1.
2.
3.
4.
The seat belt warning light blinks and the chime buzzer sounds for 6 seconds when turning the
ignition key to "ON" without fastening the seat belt. After fastening the seat belt, the chime buzzer
stops.
Seat Belt Warning LightChime Buzzer

02-298710-01
▶Parking Brake Warning
The parking brake warning light comes on for approx. 4 seconds when turning the ignition
key from the "OFF" to the "ON" position regardless of the vehicle speed and the parking
brake switch position. After this 4 seconds, the warning light comes on, goes off or blinks
according to the vehicle speed and the parking brake switch position.
The warning light comes on when the parking brake is applied and the vehicle speed is
below 10 km/h.
The warning light goes off when releasing the parking brake under step (2).
The warning light blinks and the chime buzzer sounds for 2.5 seconds and stops for 1.5
seconds when the vehicle speed is over 10 km/h for more than 2 seconds while the
parking brake is applied.
The warning light goes off and the chime buzzer stops when releasing the parking brake
under step (4).
The warning light comes on and the chime buzzer stops when the vehicle speed goes
down below 10 km/h under step (4).
This function does not work when the ignition switch is in "OFF" position. 1.
2.
3.
4.
5.
6.
7.

02-458710-01
3. STICS CONTROL REGARDING THEFT WARNING ALARM
1) Armed mode
The followings are definition of DOOR OPEN/CLOSE and DOOR LOCK/UNLOCK in respect of
theft deterrent system. -
DOOR OPEN and DOOR CLOSE
DOOR OPEN: - Any of all door switches (including engine hood, driver's door, passenger's
door or rear door) is in "OPEN" position.
DOOR CLOSE: - All door switches (including engine hood, driver's door, passenger's door,
rear door and tailgate) are in "CLOSE" position.
The door lock/unlock operation does not affect the engine hood.
OPEN/CLOSE of the dech tailgate does not affect entering the armed mode.
In other words, when the hood and front/rear door are closed even if the dech tailgate is
open, the vehicle can enter the armed mode. -
-
DOOR LOCK & DOOR UNLOCK
DOOR LOCK: -
Indicates that driver's, passenger's and rear door and tailgate lock switches
are in LOCK positions.
DOOR UNLOCK: -
Indicates that driver's, passenger's or rear door or tailgate lock switches
are in UNLOCK positions.
Engine hood open warning lamp
The warning lamp comes on when the engine
hood is open.
Since the luggage room tailgate does not have the door switch, the door ajar warning light
does not come on when it is open.

02-46
2) Description of Theft Deterrent Function
(1) Armed mode activation requirements
The "LOCK" output is "ON" when the "LOCK" signal is received from transmitter while the
ignition key is removed and all doors are closed.
The armed mode is activated when the door lock switch is locked (hazard warning flasher
blink twice).
The armed mode is still activated and the hazard warning flasher blink twice when the
"LOCK" signal is received from the remote control key again in armed mode.
When the "LOCK" signal is received from the remote control key while any of doors is not
closed, only the "LOCK" output can be done and then activates the armed ready mode
(without theft deterrent horn and hazard warning flasher). At this moment, if the ignition key is
inserted or the door lock switch is unlocked, it cancels the armed mode and activates the
normal mode.
When the door is opened or the ignition key is not inserted into ignition switch within 30
seconds after receiving "UNLOCK" signal from the remote control key, it outputs "LOCK" and
then activates armed mode (RELOCK operation). Also, at this moment, the system blinks
hazard warning flasher twice.
The armed mode will not be activated except above conditions.
Ex) The armed mode will not be activated when the door is locked by the ignition key. a.
b.
c.
d.
e.