warning SSANGYONG NEW ACTYON SPORTS 2012 Owner's Guide

03-6
3. FUNCTIONS OF IMMOBILIZER & RECHARGEABLE KEY
The functions of the immobilizer and rechargeable key are similar to that of the normal REKES
key. But, there are the immobilizer function that permits the engine to start only after confirming
the encrypted coding and battery charging function.
The followings are common functions of the normal REKES key and the immobilizer &
rechargeable key.
Door Unlock and Panic Function
Breifly press (below 0.5 sec): Door unlock and
　　　　　　　　　　　　 theft deterrent
mode deactivated
Press and hold (over 2 sec): Panic function
1. Door unlock (Briefly press)
If you send the door unlock signal using the
remote control key, with all the doors locked,
the door will be opened and the theft
deterrent mode will be deactivated. If the
door coupled switch of front room lamp is
pressed, the lamp will come on for 30
seconds. It will turn off immediately after the
lock button of the remote control is pressed.
2. Panic function: activated in the theft deterrent mode
When pressing the door UNLOCK and PANIC button for
approx. 2 seconds or longer, the warning alarm sounds
and the hazard warning lamp blinks for approx. 27
seconds.
The function is inactivated if any button of remote control
is pressed. ·
·
Breifly press (below 0.5 sec): Door lock and theft deterrent mode is activated
Press and hold (over 0.5 sec): Escort function
1. Door unlock (Briefly press)
Pressing this button locks all doors and activates the theft deterrent mode.
2. Escort function
If you press the button for more than 0.5 seconds in theft deterrent mode, the headlamp
comes on for about 20 seconds.
This function is deactivated if you press the door lock button of the remote control key. ·
·LED flasher
Briefly press: blink once
Press and hold: blink twice
Door Lock and Escort Function

03-97010-06
Immobilizer and Warning Lamp ▶
This indicator comes on when the ignition key
is communicating with the engine control unit
(during engine starting) and goes out after
starting the engine.
When turning the ignition key to the "ON"
position, the ECU (engine control unit)
transmits the challenge message to the
immobilizer & rechargeable unit.
(This is to verify whether the key is valid. If the
verification fails, it transmits re-verification
signals 3 times for 2 seconds. If three re-
verifications fail, it stops verification and starts
re-verification after 10 seconds.) (1)
ECUOnly when the two signals are identical, it recognizes the
key as the authorized one and transmits the positive
message to the ECU. (6)
The ECU enable the engine to be started. (7)
Do not drop or shock to the transponder in the key as it may be damaged.
With a damaged transponder, the engine cannot be started.
When you erase the code or register an extra key, please attend on the site.
In any cases, the immobilizer system can not be removed from the vehicle. If you attempt to
remove it and damage the system, starting will be impossible, so never attempt to remove,
damage or modify it.
The remote engine starter cannot be installed to the vehicle equipped with the immobilizer
system. ·
·
·
·
·ON: In communication
Blinks twice at one second intervals: Immobilizer
system fault
Blinks once at 2 second intervals: Immobilizer unit
not coded
The immobilizer indicator does not come
on if the communication time between
immobilizer key and ECU is too short.
Instrument
panel

03-137010-06
5. REKES OPERATION LOGIC
1) Remote Door Lock
When briefly pressing the door lock switch on the remote control key for less than 0.5
seconds, all doors are locked.
The system outputs the "LOCK" signal immediately after receiving the door lock message from
the remote control key. If the vehicle is locked while all doors including engine hood are
closed, the theft deterrent mode is activated (hazard warning lamps are blinking twice). 1.
2.

03-14
2) Door Unlock
When briefly pressing the door unlock switch on the remote control key for less than 0.5
seconds, all doors are unlocked.
When receiving the DOOR UNLOCK message from the remote control key, the door unlock
relay is turned on for 0.5 seconds.
The hazard warning lamps blink once only when all the doors unlocked successfuly. 1.
2.
3.

04-4
1. DESCRIPTIONS OF INDICATOR DISPLAY
Tachometer
ESP indicator/warning light
Immobilizer indicator
Glow indicator
Front fog light indicator
High beam indicator
ESP OFF indicator
Seat belt reminder (driver’s seat)
Seat belt reminder (passenger’s seat)
Engine oil pressure warning light
LCD Display
Engine overheat warning light
Engine check warning light
Auto cruise indicator
Light indicator
Winter mode indicator 1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.Engine hood open warning light
Battery charge warning light
Hazard Indicator
Water separator warning light
Air bag warning light
4WD CHECK warning light
4WD LOW indicator
4WD HIGH indicator
Speedometer
Turn signal indicator
Coolant temperature gauge
Brake warning light
Door ajar warning light
ABS warning light
Fuel gauge
Low fuel level warning light 17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32. It sends and receives information to/from each unit through CAN communication line. The LCD
display and separate ESP ON/OFF indicator are newly added.

04-6
Connector Pin Arrangement ▶
The connector pin sections illustrated below are viewed from the front of the instrument
cluster. The arrangement of the pins is the same for both the main connector and the sub
connector.
Main connector - 20-pin (white)
Sub connector - 20-pin (gray)
1. -
2. Hood open
3. Seat belt - passenger's seat
4. -
5. -
6. Front fog lamp
7. -
8. Engine CHECK warning light
9. Charge
10. IGN 2
11. -
12. Air bag
13. Seat belt - driver's seat
14. High beam (-)
15. Right turn signal lamp (+)
16. High beam (+)
17. Left turn signal lamp (+)
18. Oil pressure
19. Parking brake signal input (STICS)
20. - 1. -
2. -
3. 4P output
4. Buzzer output
5. Illumination (+)
6. -
7. -
8. Door open
9. -
10. Battery
11. -
12. Fuel input signal
13. TRIP mode/reset switch
14. Manual transmission N (neutral)
input
15. Manual transmission R (reverse)
input
16. CAN LOW
17. CAN HIGH
18. AGND (fuel -)
19. MICOM ground
20. IGN 1

04-78210-01
Indicators on Instrument Cluster ▶
No. Symbol ItemBulb
TypePower Turning ON condition
1Turn signal lamp-L
LEDMultifunction
switchWhen activating switch
2 Turn signal lamp-R LEDMultifunction
switchWhen activating switch
34WD HIGH
indicatorLED IGN IGN ON/ CAN signal input
4Winter mode
indicatorLED IGN IGN ON/ CAN signal input
5Front fog lamp
indicatorLEDFog lamp
relayWhen activating switch
6Cruise control
indicatorLED IGN IGN ON/ CAN signal input
7Light illumination
indicator LED BATT Tail lamp ON
8High beam
indicatorLEDHeadlamp
high beam
relayWhen activating switch
9ABS warning lamp
LED IGNIGN ON/ CAN signal input
(ABS, EBD)
10 Glow indicator LED IGN IGN ON/ CAN signal input
11Immobilizer
indicatorLED IGN IGN ON/ CAN signal input
12Low fuel level
warnig lightLED IGNWhen analog inputting fuel
level

04-8
No. Symbol ItemBulb
TypePower Turning ON condition
13Engine check
warning lampLED IGN IGN ON/ CAN signal input
144WD LOW
indicatorLED IGN IGN ON/ CAN signal input
15ESP indicator/
warning lightLED IGNIGN ON/ CAN signal input
(ESP & buzzer activated)
16
ESP OFF indicatorLED IGN IGN ON/ CAN signal input
17Brake warning light
LED IGNIGN ON, CAN signal input
(EBD)
184WD CHECK
indicatorLED IGN IGN ON/ CAN signal input
19Air bag warning
lampLED IGN Signal input
20Door ajar waning
lightLED BATT When door opened
21Charge warning
lampLED IGN Charge system fault
22Seat belt warning
lightLED IGN Switch input

04-98210-01
No. Symbol ItemBulb
TypePower Turning ON condition
23Engine oil pressure
warning lampLED IGN Signal input
24Water separator
warning lightLED IGN IGN ON/ CAN signal input
25Engine coolant
overheat warning
lightLED IGN IGN ON/ CAN signal input
26Engine hood open
warning lampLED IGN Switch ground
27 EBD warning light LED IGN CAN signal input

04-138210-01
3) Fuel Level Gauge
The fuel level gauge displays the resistance value of the float on the fuel sender in the fuel tank
through a pointer. Note that this vehicle doesn't have a service hole for checking the fuel sender
connector in the fuel tank.
The fuel sender and its connector can be checked and replaced only when the fuel tank is
removed. The power supply and resistance value should be measured at the connector in front of
the fuel sender (refer to wiring diagram).
When the power supply and output resistance are normal, the float operation by fuel level may be
defective; if so, replace the fuel sender.
Low fuel warning lamp comes on when:
The fuel level drops to 9 L or less. The lamp goes off if the fuel level reaches 9.5 L or more.This table shows the tolerance and resistance value changes by fuel level in normal
conditions. Therefore, the differences that can be occurred by the road conditions and fuel
fluctuations are ignored.