keyless SUBARU FORESTER 1999 Service User Guide

2. DIAGNOSTICS ITEM 1
4F21 : SELECT HORN SIGNAL OPERA-
TION.
Keep both LOCK/ARM and UNLOCK/DISARM
buttons pressed for more than 1.5 seconds.
:Does the horn chirp one time?
: Go to step4F22.
: Replace keyless entry control module.

4F22 : CHECK HORN SIGNAL OUTPUT
SIGNAL.
1) Disconnect connector from keyless entry con-
trol module.
2) Measure voltage between keyless entry control
module connector (B176) and chassis ground.
Connector & terminal
(B176) No. 12 (+) Ð Chassis ground (þ):
B6M0958A
:Is the voltage more than 10 V?
: Go to step4F23.
: Go to step4F26.4F23 : CHECK HORN RELAY.
1) Remove horn relay from main fuse box.
2) Check continuity between horn relay terminals.
Terminals
No. 1 Ð No. 2:
B6M1348B
:Does continuity exist?
: Replace horn relay.
: Go to step4F24.
4F24 : CHECK HORN RELAY.
Check continuity between horn relay terminals.
Terminals
No. 3 Ð No. 4:
B6M1349B
:Does continuity exist?
: Go to step4F25.
: Replace horn relay.
63
[T4F2]6-2DIAGNOSTICS
4. Keyless Entry System

4F25 : CHECK HORN RELAY.
1) Connect the battery to horn relay terminals No.
3 and No. 4.
2) Check continuity between horn relay terminals.
Terminals
No. 1 Ð No. 2:
B6M1350B
:Does continuity exist?
: Repair wiring harness of horn circuit.
: Replace horn relay.
4F26 : CHECK FUSE.
Remove and visually check the fuse No. 6 (in main
fuse box).
:Is the fuse No. 6 blown?
: Replace fuse (15 A).
: Go to step4F27.4F27 : CHECK POWER SUPPLY FOR
HORN RELAY.
1) Install horn relay to main fuse box.
2) Measure voltage between main fuse box con-
nector (F37) and chassis ground.
Connector & terminal
(F37) No. 4 (+) Ð Chassis ground (þ):
B6M1351A
:Is the voltage more than 10 V?
: Go to step4F28.
: Repair wiring harness between main
fuse box and battery.
64
6-2[T4F2]DIAGNOSTICS
4. Keyless Entry System

4F28 : CHECK RESISTANCE BETWEEN
HORN RELAY AND KEYLESS
ENTRY CONTROL MODULE.
1) Disconnect connector from main fuse box and
keyless entry control module.
2) Measure resistance between keyless entry con-
trol module connector (B176) and main fuse box
connector (F37).
Connector & terminal
(B176) No. 12 Ð (F37) No. 4:
B6M1352A
:Is the resistance less than 10W?
: Replace keyless entry control module.

: Repair wiring harness between main
fuse box and keyless entry control mod-
ule.
3. DIAGNOSTICS ITEM 2
4F31 : CHECK FUSE.
Remove and visually check the fuse No. 2 (in main
fuse box).
:Is fuse No. 2 blown?
: Replace fuse (15 A).
: Go to step4F32.
4F32 : CHECK ROOM LIGHT BULB.
Remove and visually check the room light bulb.
:Is the bulb blown?
: Replace bulb.
: Go to step4F33.
4F33 : CHECK ROOM LIGHT SWITCH.
1) Remove room light.
2) Measure resistance of room light switch termi-
nal at the middle position.
Terminals
No. 2 Ð No. 3:
B6M0960A
:Is the resistance less than 1W?
: Repair or replace room light.
: Go to step4F34.
65
[T4F3]6-2DIAGNOSTICS
4. Keyless Entry System

4F34 : CHECK POWER SUPPLY FOR
ROOM LIGHT.
1) Disconnect connector from room light.
2) Open any door.
3) Measure voltage between room light connector
(R52) and chassis ground.
Connector & terminal
(R52) No. 2 (+) Ð Chassis ground (þ):
B6M0961A
:Is the voltage more than 10 V?
: Go to step4F35.
: Repair wiring harness between room
light and battery.4F35 : CHECK HARNESS CONNECTOR
BETWEEN ROOM LIGHT AND KEY-
LESS ENTRY CONTROL MODULE.
1) Disconnect connector from keyless entry con-
trol module.
2) Measure resistance between room light con-
nector (R52) and keyless entry control module
connector (B176).
Connector & terminal
(R52) No. 1 Ð (B176) No.4:
B6M0962A
:Is the resistance less than 10W?
: Replace keyless entry control module.

: Repair wiring harness between room
light and keyless entry control module.
66
6-2[T4F3]DIAGNOSTICS
4. Keyless Entry System

4. DIAGNOSTICS ITEM 3
4F41 : CHECK DOOR SWITCH.
1) Remove door switch.
B6M0070A
2) Move switch and check continuity between ter-
minals of door switch.
Terminals
No. 1 Ð Chassis ground
S6M0453A
:Does any fault exist in the door
switch?
: Replace door switch.
: Replace keyless entry control module.

5. DIAGNOSTICS ITEM 4
4F51 : CHECK IGNITION SWITCH.
1) Remove ignition switch.
2) Turn ignition key to each position and check
continuity between terminals of ignition switch con-
nector.
B6M1356A
:Is the ignition switch faulty?
: Replace ignition switch. [W3A1].>
: Replace keyless entry control module.

67
[T4F5]6-2DIAGNOSTICS
4. Keyless Entry System

6. DIAGNOSTICS ITEM 5
4F61 : CHECK FUSE.
Remove and visually check the fuse No. 6 (in main
fuse box).
:Is fuse No. 6 blown?
: Replace fuse (15 A).
: Go to step4F62.
4F62 : CHECK KEYLESS ENTRY CONTROL
MODULE.
1) Disconnect connector from keyless entry con-
trol module.
2) Insert the key to ignition switch (LOCK posi-
tion).
3) Measure voltage between keyless entry control
module connector (B176) and chassis ground.
Connector & terminal
(B176) No. 16 (+) Ð Chassis ground (þ):
B6M0963A
:Is the voltage more than 10 V?
: Replace keyless entry control module.

: Go to step4F63.4F63 : CHECK HARNESS CONNECTOR
BETWEEN BATTERY AND KEY
WARNING SWITCH.
1) Disconnect connector from key warning switch.
2) Measure voltage between key warning switch
connector (B74) and chassis ground.
Connector & terminal
(B74) No. 2 (+) Ð Chassis ground (þ):
B6M0964A
:Is the voltage more than 10 V?
: Go to step4F64.
: Repair wiring harness between battery
and key warning switch.
4F64 : CHECK HARNESS CONNECTOR
BETWEEN KEY WARNING SWITCH
AND KEYLESS ENTRY CONTROL
MODULE.
Measure resistance between key warning switch
connector (B74) and keyless entry control module
connector (B176).
Connector & terminal
(B74) No. 1 Ð (B176) No. 16:
B6M0965A
:Is the resistance less than 10W?
: Replace key warning switch.
: Repair wiring harness between key
warning switch and keyless entry control
module.
68
6-2[T4F6]DIAGNOSTICS
4. Keyless Entry System

C: ELECTRICAL COMPONENTS LOCATION
S6M0454A
(1) Horn
(2) Keyless entry control module
(3) Security control module (under
console box)
(4) Security indicator light (in combi-
nation meter)(5) Horn relay (in main fuse box)
(6) Rear gate latch switch
(7) Interrupt relay (behind the fuse
box)
(8) Door switch(9) Passive arm connector (on driver
side front lower pillar)
71
[T5C0]6-2DIAGNOSTICS
5. Security System

E: CONTROL MODULE I/O SIGNAL
B6M0972
Content Terminal No. Measuring condition
Empty 1 Ð
Ignition switch (ON) 2 (INPUT) Battery voltage is present when ignition switch is turned ON.
Passive arm 3 Ð
Empty 4 Ð
Door switch and rear gate latch
switch5 (INPUT) 0 V is present when any door is open.
Empty 6 Ð
Keyless entry control module 7 Ð
Keyless entry control module 8 Ð
Security indicator light 9 (OUTPUT) 0 V is present when activating the alarm operation.
Keyless entry control module 10 Ð
Power supply for clearance light
(Back-up)11 Battery voltage is constantly present.
Clearance light 12 (OUTPUT) Battery voltage is present when activating the alarm operation.
Power supply (Back-up) 13 Battery voltage is constantly present.
Ground 14 Ð
Interrupt relay 15 (OUTPUT) 0 V is present when activating the alarm operation.
Empty 16 Ð
Empty 17 Ð
Empty 18 Ð
74
6-2[T5E0]DIAGNOSTICS
5. Security System

F: DIAGNOSTICS PROCEDURE
1. BASIC DIAGNOSTICS PROCEDURE
5F11 : CHECK SECURITY SYSTEM FUNC-
TION.
1) Perform basic diagnostics procedure of keyless
entry system.
2) Perform pre-inspection.
3) Open all windows.
4) Remove ignition key from ignition switch.
5) Set the room light switch in the middle position.
6) Close all doors and the rear gate.
7) Press the LOCK/ARM button one time.
:Does the clearance light blink one
time?
: Go to step5F12.
: Go to step5F21.
5F12 : CHECK SECURITY SYSTEM FUNC-
TION.
Check if the security indicator light blinks.
:Does the security indicator light blink
every 2 seconds?
: Go to step5F13.
: Go to step5F31.
5F13 : CHECK SECURITY SYSTEM FUNC-
TION.
Press the UNLOCK/DISARM button one time.
:Does the clearance light blink two
times?
: Go to step5F14.
: Replace security control module. to 6-2 [W14A1].>
5F14 : CHECK SECURITY SYSTEM FUNC-
TION.
Check if the room light activates.
:Does the room light turn on for 30
seconds and then turn off?
: Go to step5F15.
: Replace security control module. to 6-2 [W14A1].>5F15 : CHECK SECURITY SYSTEM FUNC-
TION.
1) Unlock all doors with door locking switch in the
front door.
2) Open the front left door.
:Does the security indicator light blink
every 1/8 seconds?
: Go to step5F16.
: Go to step5F41.
5F16 : CHECK SECURITY SYSTEM FUNC-
TION.
Check if the clearance light activates.
:Does the clearance light blinking
remain?
: Go to step5F17.
: Replace security control module. to 6-2 [W14A1].>
5F17 : CHECK SECURITY SYSTEM FUNC-
TION.
Check if the horn activates.
:Does the horn sound remain?
: Go to step5F18.
: Replace security control module. 6-2 [W14A1].>
5F18 : CHECK SECURITY SYSTEM FUNC-
TION.
Turn on starter.
:Does the starter motor activate?
: Go to step5F51.
: Go to step5F19.
5F19 : CHECK SECURITY SYSTEM FUNC-
TION.
Close the front left door.
:Does the horn sound and clearance
light blinking deactivate, and starter
motor activate after approximately 30
seconds?
: Go to step5F110.
: Replace security control module. to 6-2 [W14A1].>
75
[T5F1]6-2DIAGNOSTICS
5. Security System

2.
No.1 Door
\(Door Disconnect
2 Door
\(Door a.
b.
side.Connect
Functionally
3 Door
handle
to a.
b.
adjustmentConnect
Remove
Adjust
is
4 Door
set
\(Keyless a.
b.
adjustedSame
Same
5 Child
b.Refer
6 Inner
mountingEliminate
upper
7
8 Auto
inner Auto
toSame
3.
Symptom
All
move. Driver
doesDriver
dow
move
down.Neither
side
move.
Battery
Fuse
Circuit
Main
Sub \(2\)
Motor
Motor \(3\)
Regulator \(4\)
Power
Ground
Harness \(
39
[K300]5-2DIAGNOSTICS
3.