check engine SUBARU FORESTER 2004 Service Repair Manual
[x] Cancel search | Manufacturer: SUBARU, Model Year: 2004, Model line: FORESTER, Model: SUBARU FORESTER 2004Pages: 2870, PDF Size: 38.67 MB
Page 2173 of 2870
EN(H4DOTC 2.5)-149
ENGINE (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
Step Check Yes No
1 CHECK SPEEDOMETER AND TACHOME-
TER OPERATION IN COMBINATION
METER.Does the speedometer and
tachometer operate normally?Go to step 2.Repair or replace
the combination
meter.
Meter System.>
2 CHECK INPUT SIGNAL FROM ECM.
1) Turn the ignition switch to ON. (engine OFF)
2) Measure the voltage between ECM con-
nector and chassis ground.
Connector & terminal
(B136) No. 20 (+) — Chassis ground (
−):Is the voltage more than 4.75
V?Go to step 3.Even if the malfunc-
tion indicator light
illuminates, the cir-
cuit has returned to
a normal condition
at this time. A tem-
porary poor contact
of the connector
may be the cause.
N
OTE:
In this case repair
the following:
Poor contact in
fuel pump connec-
tor
Poor contact in
coupling connector
3 CHECK INPUT VOLTAGE OF ECM.
1) Turn the ignition switch to OFF.
2) Disconnect the combination meter connec-
tor (i11) and ECM connector.
3) Turn the ignition switch to ON.
4) Measure the voltage of harness between
ECM and chassis ground.
Connector & terminal
(B136) No. 20 (+) — Chassis ground (
−):Is the voltage more than 4.75
V?Go to step 4.Repair battery
short circuit
between ECM and
combination meter
connector.
4 CHECK HARNESS BETWEEN ECM AND
FUEL TANK CORD.
1) Turn the ignition switch to OFF.
2) Separate fuel tank cord connector (R57)
and rear wiring harness connector (R15).
3) Measure the resistance between ECM and
fuel tank cord.
Connector & terminal
(B136) No. 20 — (R15) No. 7:Is the resistance less than 5
Ω?Go to step 5.Repair open circuit
between ECM and
fuel tank cord.
5 CHECK HARNESS BETWEEN FUEL TANK
CORD AND CHASSIS GROUND.
Measure the resistance between fuel tank cord
and chassis ground.
Connector & terminal
(R15) No. 3 — Chassis ground:Is the resistance less than 5
Ω?Go to step 6.Repair open circuit
between fuel tank
cord and chassis
ground.
N
OTE:
In this case repair
the following:
Poor contact in
coupling connector
6 CHECK FUEL TANK CORD.
1) Disconnect the connector from fuel level
sensor.
2) Measure the resistance between fuel level
sensor and coupler connector.
Connector & terminal
(R57) No. 3 — (R58) No. 5:Is the resistance less than 10
Ω?Go to step 7.Repair open circuit
between coupling
connector and fuel
level sensor.
Page 2174 of 2870
EN(H4DOTC 2.5)-150
ENGINE (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
7 CHECK FUEL TANK CORD.
1) Disconnect the connector from fuel sub
level sensor.
2) Measure the resistance between fuel level
sensor and fuel sub level sensor.
Connector & terminal
(R58) No. 3 — (R59) No. 2:Is the resistance less than 10
Ω?Go to step 8.Repair open circuit
between fuel level
sensor and fuel
sub level sensor.
8 CHECK FUEL TANK CORD.
Measure the resistance between fuel sub level
sensor and coupler connector.
Connector & terminal
(R57) No. 2 — (R59) No. 1:Is the resistance less than 10
Ω?Go to step 9.Repair open circuit
between coupling
connector and fuel
sub level sensor.
9 CHECK FUEL LEVEL SENSOR.
1) Remove the fuel pump assembly.
2) While moving the fuel level sensor float up
and down, measure resistance between fuel
level sensor terminals.
Te r m i n a l s
No. 2 — No. 3:Is the resistance more than 53
Ω?Replace the fuel
level sensor.
2.5)-54, Fuel Level
Sensor.>Go to step 10.
10 CHECK FUEL SUB LEVEL SENSOR.
1) Remove the fuel sub level sensor.
2) While moving the fuel sub level sensor float
up and down, measure resistance between
fuel sub level sensor terminals.
Te r m i n a l s
No. 1 — No. 2:Is the resistance more than 45
Ω?Replace the fuel
sub level sensor.
55, Fuel Sub Level
Sensor.>Replace the com-
bination meter.
Meter Assembly.> Step Check Yes No
Page 2176 of 2870
EN(H4DOTC 2.5)-152
ENGINE (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
Step Check Yes No
1 CHECK HARNESS BETWEEN VEHICLE
SPEED SENSOR AND ECM CONNECTOR.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from vehicle
speed sensor ECM.
3) Measure the resistance of harness
between vehicle speed sensor connector and
chassis ground.
Connector & terminal
(B17) No. 1 — Chassis ground:Is the resistance more than 1
MΩ?Go to step 2.Repair ground short
circuit in harness
between vehicle
speed sensor and
ECM connector.
2 CHECK POOR CONTACT.
Check poor contact in vehicle speed sensor
connector.Is there poor contact in vehicle
speed sensor connector?Repair poor con-
tact in vehicle
speed sensor con-
nector.Replace the vehi-
cle speed sensor.
Sensor.>
Page 2178 of 2870
EN(H4DOTC 2.5)-154
ENGINE (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
Step Check Yes No
1 CHECK SPEEDOMETER OPERATION IN
COMBINATION METER.Does speedometer operate
normally?Go to step 2.Check the speed-
ometer.
eter.>
2 CHECK HARNESS BETWEEN ECM AND
COMBINATION METER CONNECTOR.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from the combi-
nation meter.
3) Measure the resistance between ECM and
combination meter connector.
Connector & terminal
(B135) No. 26 — (i10) No. 12:Is the resistance less than 10
Ω?Repair the poor
contact in ECM
connector.Repair the harness
and connector.
N
OTE:
In this case repair
the following:
Open circuit in
harness between
ECM and combi-
nation meter con-
nector
Poor contact in
ECM connector.
Poor contact in
combination meter
connector
Poor contact in
coupling connector
Page 2180 of 2870
EN(H4DOTC 2.5)-156
ENGINE (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
Step Check Yes No
1 CHECK OPERATION OF STARTER MOTOR.Does the starter motor operate
when ignition switch to ON?Repair battery
short circuit in
starter motor cir-
cuit. After repair,
replace the ECM.
41, Engine Con-
trol Module
(ECM).>Check starter motor
circuit.
55, STARTER
MOTOR CIR-
CUIT, Diagnostics
for Engine Starting
Failure.>
Page 2183 of 2870
EN(H4DOTC 2.5)-159
ENGINE (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
Step Check Yes No
1 CHECK ANY OTHER DTC ON DISPLAY.Is any other DTC displayed? Inspect the rele-
vant DTC using
“List of Diagnostic
Trouble Code
(DTC)”.
65, List of Diag-
nostic Trouble
Code (DTC).>
N
OTE:
In this case, it is
not necessary to
inspect DTC
P0519.Go to step 2.
2 CHECK AIR INTAKE SYSTEM.
1) Turn the ignition switch to ON.
2) Start and idle the engine.
3) Check the following items:
Loose installation of intake manifold and
throttle body
Cracks of intake manifold gasket and throttle
body gasket
Disconnections of vacuum hosesIs there any fault in air intake
system?Repair air suction
and leaks.Go to step 3.
3 CHECK ELECTRONIC THROTTLE CON-
TROL.
1) Turn the ignition switch to OFF.
2) Replace the electronic throttle control.
3) Check the electronic throttle control.Are foreign matters found
inside the electronic throttle
control?Remove foreign
matters from the
electronic throttle
control.Perform the diag-
nosis of DTC
P2101.
Page 2185 of 2870
EN(H4DOTC 2.5)-161
ENGINE (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
Step Check Yes No
1 CHECK CURRENT DATA.
1) Start the engine.
2) Read the data of exhaust temperature sen-
sor signal using Subaru Select Monitor or
OBD-II general scan tool.
N
OTE:
Subaru Select Monitor
For detailed operation procedure, refer to
“READ CURRENT DATA SHOWN ON DIS-
PLAY FOR ENGINE”.
OBD-II general scan tool
For detailed operation procedures, refer to the
OBD-II General Scan Tool Operation Manual.Is the temperature more than
1,200°C (2,192°F)?Go to step 2.Repair the poor
contact.
N
OTE:
In this case repair
the following:
Poor contact of
exhaust tempera-
ture sensor
Poor contact in
ECM
Poor contact in
joint connector
2 CHECK HARNESS BETWEEN EXHAUST
TEMPERATURE SENSOR AND ECM CON-
NECTOR.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from exhaust
temperature sensor.
3) Turn the ignition switch to ON.
4) Read the data of exhaust temperature sen-
sor signal using Subaru Select Monitor or
OBD-II general scan tool.
N
OTE:
Subaru Select Monitor
For detailed operation procedure, refer to
“READ CURRENT DATA SHOWN ON DIS-
PLAY FOR ENGINE”.
OBD-II general scan tool
For detailed operation procedures, refer to the
OBD-II General Scan Tool Operation Manual.Is the temperature less than
372°C (702°F)?Replace the
exhaust tempera-
ture sensor.
2.5)-40, Exhaust
Temperature Sen-
sor.>Repair ground
short circuit in har-
ness between
exhaust tempera-
ture sensor and
ECM connector.
Page 2187 of 2870
EN(H4DOTC 2.5)-163
ENGINE (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
Step Check Yes No
1 CHECK CURRENT DATA.
1) Start the engine.
2) Read the data of exhaust temperature sen-
sor signal using Subaru Select Monitor or
OBD-II general scan tool.
N
OTE:
Subaru Select Monitor
For detailed operation procedure, refer to
“READ CURRENT DATA SHOWN ON DIS-
PLAY FOR ENGINE”.
OBD-II general scan tool
For detailed operation procedures, refer to the
OBD-II General Scan Tool Operation Manual.Is the temperature less than
372°C (702°F)?Go to step 2.Repair the poor
contact.
N
OTE:
In this case repair
the following:
Poor contact of
exhaust tempera-
ture sensor
Poor contact in
ECM
Poor contact in
joint connector
2 CHECK HARNESS BETWEEN EXHAUST
TEMPERATURE SENSOR AND ECM CON-
NECTOR.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from exhaust
temperature sensor.
3) Measure the voltage between exhaust tem-
perature sensor connector and engine ground.
Connector & terminal
(B279) No. 1 (+) — Engine ground (
−):Is the voltage more than 10 V? Repair battery
short circuit in har-
ness between
ECM and exhaust
temperature sen-
sor connector.Go to step 3.
3 CHECK HARNESS BETWEEN EXHAUST
TEMPERATURE SENSOR AND ECM CON-
NECTOR.
1) Turn the ignition switch to ON.
2) Measure the voltage between exhaust tem-
perature sensor connector and engine ground.
Connector & terminal
(B279) No. 1 (+) — Engine ground (
−):Is the voltage more than 10 V? Repair battery
short circuit in har-
ness between
ECM and exhaust
temperature sen-
sor connector.Go to step 4.
4 CHECK HARNESS BETWEEN EXHAUST
TEMPERATURE SENSOR AND ECM CON-
NECTOR.
Measure the voltage between exhaust temper-
ature sensor connector and engine ground.
Connector & terminal
(B279) No. 1 (+) — Engine ground (
−):Is the voltage more than 4 V? Go to step 5.Repair the harness
and connector.
N
OTE:
In this case repair
the following:
Open circuit in
harness between
ECM and exhaust
temperature sen-
sor connector
Poor contact of
exhaust tempera-
ture sensor con-
nector
Poor contact in
ECM connector.
Poor contact in
joint connector
Page 2188 of 2870
EN(H4DOTC 2.5)-164
ENGINE (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
5 CHECK HARNESS BETWEEN EXHAUST
TEMPERATURE SENSOR AND ECM CON-
NECTOR.
1) Turn the ignition switch to OFF.
2) Measure the resistance of harness
between exhaust temperature sensor connec-
tor and engine ground.
Connector & terminal
(B279) No. 2 — Engine ground:Is the resistance less than 5
Ω?Replace the
exhaust tempera-
ture sensor.
2.5)-40, Exhaust
Temperature Sen-
sor.>Repair the harness
and connector.
N
OTE:
In this case repair
the following:
Open circuit in
harness between
ECM and exhaust
temperature sen-
sor connector
Poor contact of
exhaust tempera-
ture sensor con-
nector
Poor contact in
ECM connector.
Poor contact in
joint connector Step Check Yes No
Page 2190 of 2870
EN(H4DOTC 2.5)-166
ENGINE (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
Step Check Yes No
1 CHECK HARNESS BETWEEN ECM AND
TCM.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from ECM.
3) Disconnect the connectors from TCM.
4) Measure the resistance between ECM and
TCM connectors.
Connector & terminal
(B137) No. 18 — (B55) No. 3:
(B137) No. 26 — (B55) No. 12:Is the resistance less than 1
Ω?Go to step 2.Repair the harness
and connector.
2 CHECK HARNESS BETWEEN ECM AND
TCM.
Measure the resistance between ECM connec-
tor and chassis ground.
Connector & terminal
(B137) No. 18 — Chassis ground:
(B137) No. 26 — Chassis ground:Is the resistance more than 1
MΩ?Go to step 3.Repair the harness
and connector.
3 CHECK HARNESS BETWEEN ECM AND
TCM.
Check the resistance between ECM connec-
tors.
Connector & terminal
(B137) No. 18 — (B137) No. 26:Is the resistance more than 1
MΩ?Go to step 4.Repair the harness
and connector.
4 CHECK AT SYSTEM CONDITION.
Perform the diagnosis for AT using Subaru
Select Monitor.Is DTC P1718 displayed? Check AT system. Replace the ECM.