light SUBARU TRIBECA 2009 1.G Service Owners Manual

EI-4
General Description
EXTERIOR/INTERIOR TRIM
3. FRONT BUMPER
(1) Bumper face (4) Bumper beam reinforcementTightening torque: N·m (kgf-m, ft-lb)
(2) Front upper cover (5) Fog light coverT: 33 (3.4, 24)
(3) Energy absorber foam
EI-01251
(2)
(1)
(5)
(3)
(4)
T

EI-7
General Description
EXTERIOR/INTERIOR TRIM
7. ROOF SPOILER
(1) Roof spoiler (3) Washer nozzleTightening torque: N·m (kgf-m, ft-lb)
(2) High-mounted stop light T: 4.5 (0.46, 3.32)
EI-01254
T
T
T
(2)
(3)
(1)

EI-21
Front Bumper
EXTERIOR/INTERIOR TRIM
6. Front Bumper
A: REMOVAL
1. FRONT BUMPER FACE
1) Remove the front upper cover.
2) Turn over the front mud guard, and remove the
clips connecting the fender and bumper.
3) Remove the clips at the lower side of bumper.
4) Disconnect the fog light connector. (Model with
fog light)
5) Remove the knotch on the bumper face side
from guide bracket (A)
CAUTION:
Be careful when removing, as pulling forcefully
can damage the knotch on the bumper face
side.
NOTE:
Lift the bumper face upward, and removing in the
order of (B), (1)-(5) of the fender side, will make it
easier to remove.
6) Remove the clips, and then remove the bumper
face from vehicle body.
7) Remove the front grille from bumper face. to EI-20, REMOVAL, Front Grille.>
8) Remove the fog light from bumper face. LI-17, REMOVAL, Front Fog Light Assembly.>
EI-01268
EI-00572
EI-00573
EI-01379
(1)(2)
(3)
(4)
(5)
(B)(A)
EI-01378

EI-24
Front Bumper
EXTERIOR/INTERIOR TRIM
2. REPAIR INSTRUCTIONS FOR COLORED PP BUMPER
NOTE:
All PP bumpers are provided with a grained surface, and if the surface is damaged, it cannot normally be re-
stored to its former condition. Damages limited to the shallow scratches that cause only a change in the luster
of the base material or coating, can be almost fully restored. Before repairing a damaged area, explain this
point to the customer and obtain an understanding about the matter. Repair methods are outlined below,
based on a classification of the extent of damage.
1) Minor damage causing only a change in the luster of the bumper due to a light touch
Almost restorable.
2) Deep damage caused by scratching with fences etc.
A dent cannot be repaired but a whitened or swelled part can be removed.
Process
No.Process name Job contents
1Cleaning Clean the area to be repaired using water.
2Sanding Grind the repairing area with #500 sand paper in a “feathering” motion.
3Finish
Resin section Coated section
Repeatedly apply wax to the affected area
using soft cloth (such as flannel). Recom-
mended wax: NITTO KASEI Soft 99 TIRE
WA X B L ACK , o r e qu iva le n t.
Perfor m either the same process as for the
resin section or process No. 18 and subse-
quent in the 3) section, depending on the
degree and nature of damage.Po li sh t he waxed ar e a w i t h c le a n c lo t h a f te r 5
— 10 minutes.
Process
No.Process name Job contents
1Cleaning Clean the damaged area with water.
2Removal of dam-
aged areaCut off protruding area, if any, due to collision, using a putty knife.
3Sanding Sand the affected area with #100 — #500 sand paper.
4Finish
Resin section Coated section
Same as step 3 in the “1)” section.Perfor m step 12 and subsequent operations in
the “3)” section.

EI-31
Roof Spoiler
EXTERIOR/INTERIOR TRIM
9. Roof Spoiler
A: REMOVAL
1) Remove the rear gate upper trim. REMOVAL, Rear Gate Trim.>
2) Disconnect the connector of high-mounted stop
light and the washer hose of rear washer.
3) Remove the nuts.
4) Remove the clips, and remove the roof spoiler.
B: INSTALLATION
Install in the reverse order of removal.
Tightening torque:
4.5 N·m (0.46 kgf-m, 3.32 ft-lb)
EI-01283
EI-01284

EI-48
Sun Visor
EXTERIOR/INTERIOR TRIM
21.Sun Visor
A: REMOVAL
1) Remove the cover, loosen the mounting screws,
and remove the sun visor.
2) Disconnect the connector. (Model with vanity
mirror light)
3) While pressing the (A) on the both side using flat
tip screwdriver, pull the sun visor hook to remove it.
B: INSTALLATION
Install in the reverse order of removal.
EI-00661
EI-00662
(A)
(A)

EI-50
Roof Trim
EXTERIOR/INTERIOR TRIM
23.Roof Trim
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the spot map light. MOVAL, Spot Map Light.>
3) Remove the room light or rear entertainment
(model with rear entertainment system). LI-30, REMOVAL, Room Light.>
4) Remove the sun visor. AL, Sun Visor.>
5) Remove the assist grip. AL, Assist Grip.>
6) Remove the front pillar upper trim and center pil-
lar upper trim. Trim.>
7) Remove the rear quarter upper trim. 45, REMOVAL, Rear Quarter Trim.>
8) Remove the sunroof opening trim.
9) Remove the clips and each harness, pull out the
rear center seat belt, and remove the roof trim.
B: INSTALLATION
Install in the reverse order of removal.
EI-00501
EI-01354

GW-5
General Description
GLASS/WINDOWS/MIRRORS
4. MIRROR
B: CAUTION
•When electrical connectors are disconnected, always conduct an operational check after connecting them
again.
•Avoid impact and damage to the glass.
C: PREPARATION TOOL
1. GENERAL TOOL
(1) Outer mirror (4) Side turn signal lightTightening torque: N·m (kgf-m, ft-lb)
(2) Mirror (5) Rearview mirrorT: 2 (0.2, 1.5)
(3) Scalp cap (6) Mount
TOOL NAME REMARKS
Circuit tester Used for checking voltage and continuity.
Piano wire Used for removing the window glass.
Windshield glass knife Used for removing the window glass.
TO RX® T20Used for removing and installing the rearview mirror.
GW-00476
(5)
(6)
(2)
(3)
(4)
(1)
T

GW-20
Windshield Glass
GLASS/WINDOWS/MIRRORS
9) Apply adhesive to the glass end surface as shown.
Adhesive:
Dow Automotive
ESSEX U-400HV or equivalent
10) Fit the locating pins, and install windshield
glass using suction rubber cup.
11) Lightly press the windshield glass for tight fit.
12) Make flush the adhesive surface jutted out us-
ing spatula.
13) After completion of all work, allow the vehicle to
stand for about 24 hours.
NOTE:
•When door is opened/closed after glass is bond-
ed, always lower the door glass first, and then
open/close it carefully.
•Move the vehicle slowly.
•For minimum drying time and vehicle standing
time before driving after bonding, follow instruc-
tions or instruction manual from the adhesive man-
ufacturer.
14) After curing of adhesive, pour the water on ex-
ternal surface of vehicle to check that there are no
water leaks.
NOTE:
When a vehicle is returned to the user, tell him or
her that the vehicle should not be subjected to
heavy impact for at least three days.
15) Install the cowl panel. LATION, Cowl Panel.>
(1) Locating pin (5) Dam rubber (9) 9 mm (0.35 in)
(2) Glass (6) Fastener (10) 10 mm (0.39 in)
(3) Fastener (7) Molding front (11) 7.5 mm (0.29 in)
(4) Adhesive (8) Seal (12) 25 mm (0.98 in)
GW-00045

GW-22
Rear Gate Glass
GLASS/WINDOWS/MIRRORS
15.Rear Gate Glass
A: REMOVAL
1) Remove the rear wiper motor. REMOVAL, Rear Wiper Motor.>
2) Disconnect the electrical connectors from rear
defogger terminal.
3) Remove the glass in the same procedure as for
windshield glass. Windshield Glass.>
B: INSTALLATION
1) Mount the fastener on the body.
2) Install the dam rubber.
3) Cut off the cartridge nozzle tip as shown and set
it in sealant gun.
4) Apply adhesive in the same procedure as for
windshield glass. TION, Windshield Glass.>
5) Insert the glass clip pin into rear gate hole, push
on the area around the clip pin to secure it, and
then push lightly all around the area to seal it.
(1) Glass
(2) Spacer
(3) Adhesive
(4) Fastener
(5) 4 mm (0.15 in)
(6) 8 mm (0.31 in)
(7) 10 mm (0.39 in)
(8) 5.5 mm (0.22 in)