ECU SUBARU TRIBECA 2009 1.G Service Workshop Manual

SL-55
Immobilizer Antenna
SECURITY AND LOCKS
26.Immobilizer Antenna
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the screws, and detach the upper col-
umn cover and lower column cover.
3) Remove the instrument panel lower cover. to EI-36, REMOVAL, Instrument Panel Lower Cov-
er.>
4) Disconnect the immobilizer antenna connector
(A) and ignition switch lighting connector (B).
5) Loosen the screw and release the lock (D) at op-
posite side using flat-tip screwdriver (1), and then
detach the immobilizer antenna (C).
CAUTION:
Do not apply excessive force to remove the im-
mobilizer antenna and lock. Otherwise they
may be broken because those parts are the
products made of a plastic.
B: INSTALLATION
Install in the reverse order of removal.
SL-00258
(D)
(1)
SL-00315
(A)
(C)
(B)

SL-56
Immobilizer Antenna
SECURITY AND LOCKS

SR-3
General Description
SUNROOF/T-TOP/CONVERTIBLE TOP (SUNROOF)
B: CAUTION
•Before disassembling or reassembling parts, al-
ways disconnect the battery ground cable from bat-
tery. When replacing the audio, control unit, and
other parts provided with memory functions, record
the memory contents before disconnecting the bat-
tery ground cable in order to prevent memory dele-
tion.
•Reassemble the parts in the reverse order of dis-
assembly unless otherwise indicated.
•Adjust parts to the given specifications.
•Connect the connectors securely for reassem-
bly.
•After reassembly, make sure functional parts op-
erate smoothly.
C: PREPARATION TOOL
1. GENERAL TOOL
TOOL NAME REMARKS
Circuit Tester Used for measuring resistance and
voltage.
TO RX®T20Used for the removal of the sun roof
lid and sunshade.

SR-6
Glass Lid
SUNROOF/T-TOP/CONVERTIBLE TOP (SUNROOF)
D: FORCED DRIVE
If glass lid dose not operate or is not supplied with
power, move the glass lid using the hexagon
wrench *.
*: L shape universal purpose hexagon wrench
bolt width 4 mm (0.16 in)
1) Remove the spot map light. MOVAL, Spot Map Light.>
2) Remove the sunroof opening trim.
3) Remove the sun visor clip.
4) Insert the hexagon wrench securely until it
touches the motor shaft edge.
CAUTION:
Make sure not to bend or wrinkle the roof trim
during work.
5) Turn the hexagon wrench, and move the glass
lid.
•Turning right, the glass lid open.
•Turning left, the glass lid close.
EI-00501

SR-7
Sunroof Assembly
SUNROOF/T-TOP/CONVERTIBLE TOP (SUNROOF)
4. Sunroof Assembly
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the roof trim. AL, Roof Trim.>
3) Disconnect the harness connector of sunroof
motor.
4) Remove the glass lid. AL, Glass Lid.>
5) Remove the drain tube from frame assembly.
6) Remove the bolts, and then detach the frame as-
sembly.
B: INSTALLATION
Install in the reverse order of removal.
CAUTION:
Be careful not to snag the harness.
NOTE:
•Be sure to connect the harness connector.
•When installing the drain tube, insert it securely
into drain pipe.
Length A:
15 mm (0.59 in) or more
C: DISASSEMBLY
1) Remove the sunroof motor. MOVAL, Sunroof Motor.>
2) Remove the sunshade. MOVAL, Sunshade.>
D: ASSEMBLY
Assemble in the reverse order of disassembly.
SR-00005
A

SR-8
Sunroof Motor
SUNROOF/T-TOP/CONVERTIBLE TOP (SUNROOF)
5. Sunroof Motor
A: REMOVAL
CAUTION:
•When removing the clip, use great care not to
damage the roof trim.
•Never rotate the sunroof motor after remov-
ing it.
1) Completely close the glass lid.
2) Disconnect the ground cable from battery.
3) Remove the spot map light. MOVAL, Spot Map Light.>
4) Disconnect the harness connector, and then re-
move the motor assembly mounting screw.
CAUTION:
When removing the motor assembly, secure
the cable wires to prevent moves.
B: INSTALLATION
CAUTION:
When installing the motor assembly, be careful
not to move the sunroof cable.
1) Align the coulisse assembly and link assembly in
the same position.
2) Install the motor assembly.
3) Connect the harness connector of motor assem-
bly, and then connect the battery ground cable to
battery.
4) Perform the initialize operation of motor.
(1) Tilt up the glass lid.
(2) Release the switch once, and press the tilt
up switch again for 15 seconds.
(3) When the glass lid is raised a little and on tilt
up position, release the switch for the moment.
(4) Keep pressing the tilt up switch within 5 sec-
onds from releasing the switch, glass lid auto-
matically performs the tilts down → slides open
→ slides close operation, then the initialize op-
eration is completed.
SR-00121
(1) Front
(2) Coulisse ASSY
(3) Link ASSY
(4) 4.7 mm (0.185 in)
SR-00094
(1)
(3)
(2)(4)

WW-4
General Description
WIPER AND WASHER SYSTEMS
3. WASHER TANK
C: CAUTION
•Connect the connectors and hoses securely during reassembly.
•After reassembly, make sure functional parts operate smoothly.
•Be careful with the airbag system wire harness which passes near electrical parts and switches.
•All airbag system wiring harness and connectors are colored yellow. Do not use a tester equipment on
these circuits.
•Care must be taken when connecting the hoses to pipes so that there are no bends or blockage.
•If even a small amount of silicon oil or grease enters tank and washer fluid passages, an oil film will be
formed on the glass and will cause the wiper to chatter and judder. Make sure that no oil comes into contact
with the system.
(1) Washer nozzle (5) Front washer motorTightening torque: N·m (kgf-m, ft-lb)
(2) Washer hose (6) Rear washer motorT: 6.0 (0.61, 4.4)
(3) Washer tank (7) Grommet
(4) Washer tank cap (8) Washer motor cover

WW-6
Combination Switch (Wiper)
WIPER AND WASHER SYSTEMS
3. Combination Switch (Wiper)
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the driver’s airbag module. 15, REMOVAL, Driver’s Airbag Module.>
3) Remove the steering wheel. MOVAL, Steering Wheel.>
4) Remove the screws and remove the steering
column covers (upper & lower).
5) Disconnect the connector from the combination
switch.
6) Remove the three screws, and pull out the com-
bination base switch assembly toward you.
7) Remove the screws which secure the switch,
then remove the combination switch.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1. COMBINATION SWITCH
1) Inspect the continuity between each connector
terminal.
2) If continuity is not as specified, replace the
switch.
SL-00258
LI -00332
Switch positionTerminal No.Standard
Fr o n t
LO 7 and 17 Less than 1 Ω
HI 8 and 17 Less than 1 Ω
Washer ON 2 and 11 Less than 1 Ω
Rear
Washer ON 2 and 12 Less than 1 Ω
OFF
2 and 10
2 and 12
2 and 13
10 and 12
10 and 13
12 and 13
1 MΩ or more
INT 2 and 13 Less than 1 Ω
ON 2 and 10 Less than 1 Ω
Washer ON
2 and 12
12 and 10
2 and 10
Less than 1 Ω
WW-00046
87654321917 16 15 14 13 12 11 1018

WW-10
Wiper Blade
WIPER AND WASHER SYSTEMS
4. Wiper Blade
A: REMOVAL
CAUTION:
When replacing the wiper blade, if standing up
the wiper arm, be sure to stand up the driver’s
side wiper arm first, and then passenger’s side
wiper arm next. Also, when putting the wiper
arms back, be sure to start with passenger’s
side first, then driver’s side next. Doing this in
the reverse order may result in the driver’s side
wiper blade hitting the passenger’s side wiper
arm and causing damage.
1. FRONT
While pushing the locking clip to the direction of the
arrow, pull out and remove the blade from the arm.
2. REAR
Turn the blade in the direction of arrow (A) and re-
move it from arm.
B: INSTALLATION
1) Install in the reverse order of removal.
2) Confirm that the clip is locked securely.
C: DISASSEMBLY
1. FRONT
Pull side (A) of the wiper rubber stopper and re-
move the rubber from the blade assembly.
2. REAR
Pull the wiper rubber top slightly from stopper (A)
and pull out completely.
WW-00354
(A) Turn the wiper blade.
(1) Wiper arm
(2) Wiper blade
(3) Wiper blade attachment section
(1)
(2)
(3)(A)WW-00207
WW-00009
WW-00143
(A)

WW-11
Wiper Blade
WIPER AND WASHER SYSTEMS
D: ASSEMBLY
1. FRONT
1) Insert the wiper rubber onto the blade so that the
stopper is in the position shown in the figure.
2) Make sure the wiper rubber is securely fastened
to pull stopper (A).
2. REAR
WW-00230
WW-00037
WW-00193
ABCD