torque SUBARU TRIBECA 2009 1.G Service Workshop Manual
[x] Cancel search | Manufacturer: SUBARU, Model Year: 2009, Model line: TRIBECA, Model: SUBARU TRIBECA 2009 1.GPages: 2453, PDF Size: 46.32 MB
Page 1141 of 2453
CO(H6DO)-22
Radiator Main Fan and Fan Motor
COOLING
(5) Remove the bolts on the right side of the ra-
diator stay.
13) Disconnect the connector from radiator fan
control unit.
14) Remove the reservoir tank.
15) Remove the bolts on the upper side of the radi-
ator fan shroud.
16) Remove the radiator fan shroud.
NOTE:
When pulling the radiator fan shroud up, be careful
not to hit and damage the radiator and ATF hoses.
B: INSTALLATION
1) Tighten the bolts on the top side of the radiator
fan shroud.
Tightening torque:
7.5 N·m (0.76 kgf-m, 5.5 ft-lb)
2) Install the reservoir tank.
Tightening torque:
7.5 N·m (0.76 kgf-m, 5.5 ft-lb)
3) Connect the connector of the radiator fan control
unit.
CO-02181
CO-02182
CO-02183
CO-02189
CO-02189
CO-02183
CO-02182
Page 1142 of 2453
CO(H6DO)-23
Radiator Main Fan and Fan Motor
COOLING
4) Install the radiator stay.
(1) Install the latch.
Tightening torque:
33 N·m (3.4 kgf-m, 25 ft-lb)
(2) Connect the radiator hose brackets.
(3) Hold the harness to the radiator stay with a
clip.
(4) Tighten the bolts on the left side of the radi-
ator stay.
Tightening torque:
18 N·m (1.8 kgf-m, 13.3 ft-lb)
(5) Tighten the bolts on the right side of the ra-
diator stay.
Tightening torque:
18 N·m (1.8 kgf-m, 13.3 ft-lb)
5) Install the radiator upper brackets.
Tightening torque:
12 N·m (1.2 kgf-m, 8.9 ft-lb)
6) Install the front upper cover.
7) Install the air intake duct.
8) Lift-up the vehicle.
CO-02179
CO-02180
CO-02181
CO-02177
CO-02176
Page 1143 of 2453
CO(H6DO)-24
Radiator Main Fan and Fan Motor
COOLING
9) Tighten the bolts on the lower side of the radiator
stay.
Tightening torque:
18 N·m (1.8 kgf-m, 13.3 ft-lb)
10) Tighten the bolts on the lower side of the radia-
tor fan shroud.
Tightening torque:
7.5 N·m (0.76 kgf-m, 5.5 ft-lb)
11) Install the under cover.
12) Lower the vehicle.
13) Connect the ground cable to battery.
14) Install the collector cover.
C: DISASSEMBLY
1) Disconnect the connector from radiator fan con-
trol unit.
2) Remove the radiator main fan.
3) Remove the radiator main fan motor.
D: ASSEMBLY
Assemble in the reverse order of disassembly.
Tightening torque:
3.8 N·m (0.39 kgf-m, 2.8 ft-lb)
Tightening torque:
6.3 N·m (0.64 kgf-m, 4.6 ft-lb)
(A) Connector
(B) Clip
CO-02175
CO-02188
CO-02190
(A)
(B)
CO-02199
CO-02200
CO-02200
CO-02199
Page 1144 of 2453
CO(H6DO)-25
Radiator Sub Fan and Fan Motor
COOLING
9. Radiator Sub Fan and Fan
Motor
A: REMOVAL
Refer to the radiator main fan & fan motor.
Fan Motor.>
B: INSTALLATION
Refer to the radiator main fan & fan motor.
Fan and Fan Motor.>
C: DISASSEMBLY
1) Disconnect the connector from radiator fan con-
trol unit.
2) Remove the radiator sub fan.
3) Remove the radiator sub fan motor.
D: ASSEMBLY
Assemble in the reverse order of disassembly.
Tightening torque:
3.8 N·m (0.39 kgf-m, 2.8 ft-lb)
Tightening torque:
6.3 N·m (0.64 kgf-m, 4.6 ft-lb)
(A) Connector
(B) Clip
CO-02201
(A)(B)
CO-02202
CO-02203
CO-02203
CO-02202
Page 1146 of 2453
CO(H6DO)-27
Reservoir Tank
COOLING
11) Remove the reservoir tank.
B: INSTALLATION
1) Install the reservoir tank.
Tightening torque:
7.5 N·m (0.76 kgf-m, 5.5 ft-lb)
2) Install the radiator stay.
(1) Install the latch.
Tightening torque:
33 N·m (3.4 kgf-m, 25 ft-lb)
(2) Install the radiator hose bracket.
(3) Hold the harness to the radiator stay with a
clip.
(4) Tighten the bolts on the left side of the radi-
ator stay.
Tightening torque:
18 N·m (1.8 kgf-m, 13.3 ft-lb)
(5) Tighten the bolts on the right side of the ra-
diator stay.
Tightening torque:
18 N·m (1.8 kgf-m, 13.3 ft-lb)
CO-02183
CO-02183
CO-02179
CO-02180
CO-02181
Page 1147 of 2453
CO(H6DO)-28
Reservoir Tank
COOLING
3) Install the radiator upper brackets.
Tightening torque:
12 N·m (1.2 kgf-m, 8.9 ft-lb)
4) Install the front upper cover.
5) Install the air intake duct.
6) Lift-up the vehicle.
7) Tighten the bolts on the lower side of the radiator
stay.
Tightening torque:
18 N·m (1.8 kgf-m, 13.3 ft-lb)
8) Install the under cover.
9) Lower the vehicle.
10) Install the collector cover.
C: INSPECTION
Make sure the engine coolant level is between
“FULL” and “LOW”.
CO-02177
CO-02176
CO-02175
Page 1148 of 2453
CO(H6DO)-29
Radiator Fan Control Unit
COOLING
11.Radiator Fan Control Unit
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the air intake duct.
3) Remove the front upper cover.
4) Remove the radiator fan control unit.
(1) Disconnect the connector from radiator fan
control unit.
(2) Remove the screws which hold the radiator
fan control unit.
B: INSTALLATION
Install in the reverse order of removal.
Tightening torque:
2.6 N·m (0.27 kgf-m, 1.9 ft-lb)
(A) Connector
(B) Screw
CO-02176
CO-02204
(A)
(B)
Page 1150 of 2453
EC(H6DO)-2
General Description
EMISSION CONTROL (AUX. EMISSION CONTROL DEVICES)
1. General Description
A: CAUTION
•Wear work clothing, including a cap, protective
goggles and protective shoes during operation.
•Remove contamination including dirt and corro-
sion before removal, installation or disassembly.
•Keep the disassembled parts in order and pro-
tect them from dust and dirt.
•Before removal, installation or disassembly, be
sure to clarify the failure. Avoid unnecessary re-
moval, installation, disassembly and replacement.
•Be careful not to burn yourself, because each
part on the vehicle is hot after running.
•Be sure to tighten fasteners including bolts and
nuts to the specified torque.
•Place shop jacks or rigid racks at the specified
points.
•Before disconnecting connectors of sensors or
units, be sure to disconnect the ground cable from
the battery.
Page 1153 of 2453
EC(H6DO)-5
Canister
EMISSION CONTROL (AUX. EMISSION CONTROL DEVICES)
4. Canister
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Lift-up the vehicle.
3) Remove the clip holding the harness.
4) Remove the rear suspension assembly.
5) Disconnect the following hoses and connectors.
(1) Evaporation hose
(2) Connector
6) Remove the canister from body.
B: INSTALLATION
Install in the reverse order of removal.
Tightening torque:
8.0 N·m (0.82 kgf-m, 5.9 ft-lb)
C: INSPECTION
Make sure the canister and canister hoses are not
cracked or loose.
(A) Evaporation hose
(B) Connector
FU-02664
Page 1154 of 2453
EC(H6DO)-6
Purge Control Solenoid Valve
EMISSION CONTROL (AUX. EMISSION CONTROL DEVICES)
5. Purge Control Solenoid Valve
A: REMOVAL
1) Remove the collector cover.
2) Disconnect the ground cable from battery.
3) Remove the air intake chamber.
4) Disconnect the connector and hoses of purge
control solenoid valve, and then remove the purge
control solenoid valve.
B: INSTALLATION
Install in the reverse order of removal.
Tightening torque:
19 N·m (1.9 kgf-m, 14.0 ft-lb)
NOTE:
Connect the evaporation hose as shown in the fig-
ure.
C: INSPECTION
Make sure the hoses are not cracked or loose.
(A) To fuel pipe (evaporation line)
(B) To intake manifold
EC-02019
EC-02019
EC-02020
(B)
(A)