seat removal SUBARU TRIBECA 2009 1.G Service Workshop Manual

AB-6
General Description
AIRBAG SYSTEM
•Do not discard the uninflated airbag or preten-
sioner.
•When airbag control module, front sub sensor,
side airbag sensor and curtain airbag sensor are
removed, do not reuse the bolts and nuts of them.
Always use new bolts and nuts for them.
•Do not drop each airbag module, airbag control
module and each sensor, or store these parts un-
der high temperature over 93°C (199°F), or let wa-
ter, oil or grease get on them; the internal parts may
be damaged or the reliability may be greatly low-
ered.
•After removal of each parts for airbag system,
keep them with the pad facing upward on a dry,
clean and flat surface without heat, light sources,
moisture and dust.
•The airbag modules for driver’s, passenger’s,
side or curtain, or the pretensioner must not be dis-
assembled.
•When performing attachment of the steering
wheel and steering roll connector, make sure to
perform adjustment of the steering roll connector.
•The removed front seat with airbag module must
be kept at least 200 mm (8 in) away from walls and
other objects.
AB-00123
AB-00056
(1) 200 mm (8 in) or more
AB-00779
AB-00128
(1)

AB-17
Side Airbag Module
AIRBAG SYSTEM
6. Side Airbag Module
A: REMOVAL
CAUTION:
Refer to “CAUTION” of “General Description”
before handling the airbag module. 4, CAUTION, General Description.>
NOTE:
Remove the passenger’s side by referring to driv-
er’s side.
1) Turn the ignition switch to OFF.
2) Disconnect the ground cable from battery and
wait for at least 20 seconds before starting work.
3) Remove the front seats. AL, Front Seat.>
4) Disconnect the connector from the back side of
seat cushion assembly, then remove the side air-
bag harness.
5) Remove the backrest cover. ASSEMBLY, Front Seat.>
6) Remove the nuts, and remove the side airbag
module assembly from the back rest frame assem-
bly.
B: INSTALLATION
CAUTION:
•Refer to “CAUTION” of “General Description”
before handling the airbag module. 4, CAUTION, General Description.>
•Be sure to perform the system calibration for
occupant detection system after passenger’s
seat installation. CALIBRATION (REZEROING), OPERATION,
Subaru Select Monitor.>
1) Make sure that there is no foreign matter on side
airbag module.
2) Install the side airbag module (A) to backrest
frame assembly.
CAUTION:
When attaching the side airbag module assem-
bly, make sure to sandwitch the seat back cov-
er between the seat back side bracket and side
airbag module.
Tightening torque:
6.0 N·m (0.61 kgf-m, 4.4 ft-lb)
3) Install the backrest cover. SEMBLY, Front Seat.>
4) Draw the side airbag harness around the back
side of seat cushion assembly.
5) Recline the seat or slide it backward and for-
ward, and check there is no contact between the
seat backrest assembly, cushion cover assembly
and side airbag harness.
SE-00589
(1) Backrest frame ASSY
(2) Backrest cover
(3) Side airbag module ASSY
(4) Hexagon cap nut
AB-01326
(2)
(1)
(4)(3)

AB-22
Side Airbag Sensor
AIRBAG SYSTEM
9. Side Airbag Sensor
A: REMOVAL
1) Turn the ignition switch to OFF.
2) Disconnect the ground cable from battery and
wait for at least 20 seconds before starting work.
3) Remove the center pillar lower trim. 44, CENTER PILLAR LOWER TRIM, REMOVAL,
Side Trim.>
4) Remove the seat belt retractor of the front outer
seat belt. SEMBLY, REMOVAL, Front Seat Belt.>
5) Remove the nut and disconnect the airbag con-
nector to remove side airbag sensor.
B: INSTALLATION
CAUTION:
•Do not reuse the bolt and nut.
•Always use new bolts and nuts for them.
Install in the reverse order of removal.
Tightening torque:
8 N·m (0.82 kgf-m, 5.9 ft-lb)
C: INSPECTION
Check for the following, and replace the damaged
parts with new parts.
•Mounting bracket or connector of side airbag
sensor is damaged.
•Side airbag is deployed.
AB-00634

AB(diag)-69
Diagnostic Chart with Trouble Code
AIRBAG SYSTEM (DIAGNOSTICS)
Step Check Yes No
1CHECK POOR CONTACT.
1) Turn the ignition switch to OFF, disconnect
the battery ground cable, and wait more than
20 seconds.
2) Confirm that the connector that is between
the airbag control module and the passenger’s
side warning box is securely connected.
Is there poor contact in any
connector?
Replace the airbag
harness connec-
tor.
Go to step 2.
2CHECK AIRBAG MAIN HARNESS.
1) Disconnect the connector (AB6) from air-
bag control module.
2) Connect the battery ground terminal and
turn the ignition switch to ON.
NOTE:
Neither of ON/OFF illuminates when it is nor-
mal.
Is the passenger's seat airbag
indicator lit?
Go to step 3.Go to step 4.
3CHECK AIRBAG MAIN HARNESS.
1) Turn the ignition switch to OFF.
2) Remove the passenger’s side warning box
and disconnect the connector (i116).
3) Connect the connector (1U) in the test har-
ness U to connector (AB6).
4) Measure the resistance between connec-
tors (2U) and (4U) in the test harness U and
chassis ground.
Connector & terminal
(2U) No. 14 — (4U) No. 17:
(2U) No. 14 — Chassis ground:
(4U) No. 17 — Chassis ground:
Is the resistance more than 1
MΩ?
Replace the pas-
senger’s side
warning box. to AC-46,
REMOVAL, Air
Ve n t G r i l l e . >
Repair the bulk-
head harness. Or
replace the airbag
main harness with
body harness.
4CHECK THE AIRBAG HARNESS.
1) Connect the connectors (7U) and (8U) in
the test harness U.
2) Connect the battery ground terminal and
turn the ignition switch to ON.
Is the passenger's seat airbag
indicator lit?
Replace the airbag
control module.
Airbag Control
Module.>
Go to step 5.
5CHECK THE AIRBAG HARNESS.
1) Turn the ignition switch to OFF.
2) Connect the connector (1U) in the test har-
ness U to connector (AB6).
3) Measure the resistance between connec-
tors (2U) and (4U) in the test harness U and
the connector (i116).
Connector & terminal
(2U) No. 14 — (i116) No. 5:
(4U) No. 17 — (i116) No. 6:
Is the resistance less than 10
Ω?
Go to step 6.Repair the bulk-
head harness. Or
replace the airbag
main harness with
body harness.
6CHECK BODY HARNESS.
1) Turn the ignition switch to ON.
2) Measure the voltage between connector
(i116) and chassis ground.
Connector & terminal
(i116) No. 3 — Chassis ground:
Is the voltage more than 10 V? Replace the pas-
senger’s side
warning box. to AC-46,
REMOVAL, Air
Ve n t G r i l l e . >
Repair the power
supply line to the
passenger’s side
warning box.

ET-23
Navigation Body
ENTERTAINMENT
18.Navigation Body
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the driver’s seat. MOVAL, Front Seat.>
3) Remove the cover attachment bolts, and remove
the cover.
4) Disconnect the connector.
5) Remove the bolts and then remove the naviga-
tion unit.
B: INSTALLATION
Install in the reverse order of removal.
ET-00195
ET-00185

EI-45
Rear Quarter Trim
EXTERIOR/INTERIOR TRIM
19.Rear Quarter Trim
A: REMOVAL
1) Remove the third-row seats. REMOVAL, Third-row Seats.>
2) Remove the rear door scuff plate. REMOVAL, Side Trim.>
3) Remove the lower anchor cover.
4) Remove the luggage floor mat and utility box.
5) Remove the luggage floor end cover.
6) Remove the cover, and remove the bolts inside.
7) Remove the rear quarter lower trim.
8) Remove the rear quarter top trim.
9) Remove the lower anchor bolts of second-row
seat belts.
10) Remove the upper and lower anchor bolts of
third-row seat belts.
11) Remove the cover, and remove the bolts in-
side.
12) Remove the cap (A) on the upper side of pillar
trim, and remove the bolt inside.
EI-01344
EI-01345
EI-01346
EI-01347
EI-01353
EI-01348
EI-01349
EI-01377

EI-47
Floor Mat
EXTERIOR/INTERIOR TRIM
20.Floor Mat
A: REMOVAL
1. FRONT FLOOR MAT
1) Remove the front seats. AL, Front Seat.>
2) Remove the second–row seats. REMOVAL, Second-row Seats.>
3) Remove the console box. MOVAL, Console Box.>
4) Remove the instrument panel lower cover. to EI-36, REMOVAL, Instrument Panel Lower Cov-
er.>
5) Remove the glove box. AL, Glove Box.>
6) Remove the following trims. MOVAL, Side Trim.>
•Front door scuff plate
•Rear door scuff plate
•Front pillar lower trim
•Center pillar lower trim
7) Remove the remote opener cover. 45, REMOVAL, Remote Openers.>
8) Remove the navigation unit. MOVAL, Navigation Body.>
9) Remove the clips, then remove the front floor
mats.
2. REAR FLOOR MAT
1) Remove the second–row seats. REMOVAL, Second-row Seats.>
2) Remove the third-row seats. (7 seater mod-
el)
3) Remove the luggage box (front). (5 seater mod-
el)
4) Remove the rear quarter lower trim. 45, REMOVAL, Rear Quarter Trim.>
5) Remove the clips, then remove the rear floor
mats.
B: INSTALLATION
Install in the reverse order of removal.
NOTE:
•Secure the mat firmly with hook and clip.
•Insert the mat edge firmly into the groove of side
sill cover.
EI-01351
EI-01352

EI-50
Roof Trim
EXTERIOR/INTERIOR TRIM
23.Roof Trim
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the spot map light. MOVAL, Spot Map Light.>
3) Remove the room light or rear entertainment
(model with rear entertainment system). LI-30, REMOVAL, Room Light.>
4) Remove the sun visor. AL, Sun Visor.>
5) Remove the assist grip. AL, Assist Grip.>
6) Remove the front pillar upper trim and center pil-
lar upper trim. Trim.>
7) Remove the rear quarter upper trim. 45, REMOVAL, Rear Quarter Trim.>
8) Remove the sunroof opening trim.
9) Remove the clips and each harness, pull out the
rear center seat belt, and remove the roof trim.
B: INSTALLATION
Install in the reverse order of removal.
EI-00501
EI-01354

AC-47
Heater Duct
HVAC SYSTEM (HEATER, VENTILATOR AND A/C)
26.Heater Duct
A: REMOVAL
1. FRONT HEATER DUCT
1) Remove the instrument panel lower cover. to EI-36, REMOVAL, Instrument Panel Lower Cov-
er.>
2) Remove the catch and detach the front heater
duct (A).
2. REAR HEATER DUCT
1) Remove the heater cooling unit. REMOVAL, Heater and Cooling Unit.>
2) Remove the front seats. AL, Front Seat.>
3) Remove the front side sill cover.
4) Pull off the floor mat to remove the rear center
heater duct (A) and rear heater duct LH, RH (B).
B: INSTALLATION
Install in the reverse order of removal.
AC-01349
(A)
AC-01350
(A)
(B)

LI-11
Headlight Assembly
LIGHTING SYSTEM
10.Headlight Assembly
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the air intake duct.
3) Remove the engine front cover.
4) Disengage the three clips, and then turn over the
mud guard.
5) Remove the three bolts securing the headlight
assembly from the lower side of vehicle.
6) Remove the two bolts and then remove the
headlight assembly.
7) Disconnect the connector and then detach the
rear headlight assembly.
B: INSTALLATION
Install in the reverse order of removal.
C: ADJUSTMENT
1. HEADLIGHT AIMING
NOTE:
Aiming of this headlight can be adjusted only in the
vertical direction. It cannot be adjusted in the hori-
zontal direction.
CAUTION:
Turn off the light before adjusting the headlight
beam level. If it is necessary to inspect the
beam level, do not turn on the lamp for more
than two minutes.
NOTE:
Before checking the headlight beam level, be sure
of the following:
•Check the area around the headlight for any
scratches, damage or other type of deformation.
•Make sure that the vehicle is parked on a level
surface.
•Make sure that the inflation pressure of tires are
correct.
•Check that the vehicle fuel tank is full.
1) Bounce the vehicle several times to normalize
the suspension.
2) Make certain that someone is seated in the driv-
er's seat.
IN-02134
CO-02176
LI-00503
LI-00504