ESP SUZUKI BALENO 1999 1.G User Guide

60G-74E
OPERATING YOUR VEHICLE

Reduce your speed and change

down to a lower gear before going

down a long or steep hill. A lower

gear will allow the engine to provide

braking. Avoid riding the brakes or

they may overheat, resulting in brake

failure.

When driving on slippery roads, be

sure to slow down before changing

down. Excessive and or sudden

changes in engine speed may cause

loss of traction, which could cause

you to lose control.

Make sure that the vehicle is

completely stationary before you

change into reverse.
CAUTION

To help avoid clutch damage, do not

use the clutch pedal as a footrest

while driving or use the clutch to

keep the vehicle stationary on a hill.

Depress the clutch fully when

changing gear.

When changing gears or starting off,

do not race the engine. Racing the

engine can shorten engine life and

prevent smooth operation.
BRAKING

The distance needed to bring any vehicle to a

halt increases with the speed of the vehicle.

The braking distance needed, for example, at

60 km/h will be approximately 4 times greater

than the braking distance needed at 20 km/h.

Start to brake the vehicle when there is plenty

of distance between your vehicle and the

stopping point, and slow down gradually.

69

7-4

OPERATING YOUR VECHILE

60G-74E

RUNNING-IN

Servo assisted brakes

Your vehicle has servo assisted brakes which

works with the assistance of engine vacuum.

Do not switch off the engine while

vehicle is in motion, for example, while

driving down a hill as this will cause

loss of vacuum assistance leading to

reduction of braking efficiency

substantially.

If servo assistance is lost due to a stalled

engine or other failures, the system is still fully

operational on reserve power and you can

bring the vehicle to a complete stop by

pressing the brake pedal once and holding it

down. The reserve power is partly used up

each time you depress the brake pedal. Apply

smooth and constant pressure to the pedal.

Do not pump the pedal.
Even without reserve power in the

brake system, you can still stop the

vehicle by pressing the brake pedal

harder than normally required.

However, the stopping distance may be

lonaer.

On loose surface where the wheels can

easily loose traction (such as gravel,

etc.), the stopping distance required for

your vehicle may be greater than for a

comparable vehicle with a conventional

brake system. Allow for extra stopping

distance when driving on loose

surfaces.
CAUTION

The future performance and reliability

of the engine depends on the care and

restraint exercised during its early life.

It is especially important to observe the

following precautions during the initial

1000 km of vehicle operation.

• After starting, do not race the

engine. Warm it up gradually.

• Avoid prolonged vehicle operation at

a constant speed. Moving parts will

bed in better if you vary your speed.

• Do not exceed 100 km/h.

• Start off from a stop slowly. Avoid

full throttle starts.

• If possible, avoid hard braking,

especially during the first 300 km of

driving.

• Do not drive slowly with the

transmission in a high gear.

• Drive the vehicle at moderate engine

speeds.

7-5
70
If water gets into the brake drums,

brake performance may become poor

and unpredictable. After driving

through water or washing the

underside of the vehicle, test the brakes

while driving at a slow speed to see if

they have maintained their normal

effectiveness. If the brakes are less

effective than normal, dry them by

repeatedly applying the brakes while

driving slowly until the brakes have

regained their normal effectiveness.

60G-74E
DRIVING TIPS AND SAFE DRIVING

72F-08-011

Braking

1. Use the parking brake when parking your

vehicle and shift the gear shift lever into

the first gear or reverse gear position for

the sake of safety.
72F-08-012

Don't use handbraking unless

unavoidable. It causes the vehicle to

skid and a rear end collision occur. It is

especially dangerous when the tyres are

worn, for they allow a larger skid.

Use foot brake in three stages

(1) Warn the vehicle behind you

(2) Gradually apply the brake.

(3) Bring the vehicle to a halt.
3. When driving on a downhill, try not to apply

the brake but use the engine brake

effectively. Overuse of the footbrake may

result in total brake failure.

79

8-6

DRIVING TIPS AND SAFE DRIVING

60G-74E

72F-08-014

Avoid reckless high speed driving and try

to drive at a safe speed suitable for the

road conditions while maintaining a

constant speed.
5.
72F-08-015

The higher the speed, the narrower the

driver's visual range becomes. In such a

state, it is difficult to anticipate any hazard

and the driver feels much fatigued.

Never do sharp handling during high

speed driving. You will lose your control

over your car.

When overtaking or changing the lane

while driving at a high speed, keep an

ample car-to-car distance.

72F-08-017

8-7
80
72F-08-013

72F-08-016

60G-74E
INSPECTION AND MAINTENANCE

INSPECTION AND MAINTENANCE

Periodic Maintenance Schedule.. 9-2

Engine Oil and Filter 9-7

Gear OH 9-10

Engine Coolant 9-11

Windscreen Washer Fluid 9-13

Air Cleaner 9-13

Spark Plugs 9-14

Brakes 9-15

Steering 9-17

Power Steering (if equipped) 9-18

Clutch Pedal 9-18

Tyres... 9-19

Battery 9-22

Fuses 9-23

Bulb Replacement , 9-25

Wiper Blades 9-29

83

INSPECTION AND MAINTENANCE

60G-74E

70F-05-002

You should take extreme care when

working on your vehicle to prevent

accidental injury. Here are a few

precautions that you should be

especially careful to observe:

• Do not leave the engine running in

garages or other confined areas.

• When the engine Is running, keep

hands, clothing, tools, and other

objects away from the fan and water

pump belt. Even though the fan may

not be moving, it can automatically

turn on without warning. ^
When it is necessary to do service

work with the engine running, make

sure that the parking brake is applied

fully and the transmission is in

Neutral.

Do not touch ignition wires or other

ignition system parts when starting

the engine or when the engine is

running, or you could receive an

electric shock.

Be careful not to touch a hot engine,

exhaust manifold and pipes, muffler,

radiator and water hoses.

Do not allow smoking, sparks, or

flames around gasoline or the

battery. Flammable fumes are

present.

Do not get under your vehicle if it is

supported only with the portable

jack provided in your vehicle.

Be careful not to cause accidental

short circuits between the positive

and negative battery terminals.

Keep used oil, coolant, and other

fluids away from children and pets.

Dispose of used fluids properly;

never pour them on the ground, into

sewers, etc.

9-1
84

60G-74E
INSPECTION AND MAINTENANCE

PERIODIC MAINTENANCE SCHEDULE

The following table shows when regular

maintenance on your vehicle is required. This

table shows in kilometres and months when

inspections, adjustments, lubrication and other

services should be performed.

Maruti recommends that maintenance

on your Maruti vehicle be performed by

Maruti Authorised Dealer/Service

Station.
CAUTION

Whenever it becomes necessary to

replace parts on your vehicle, it is

recommended that you use MARUTI

GENUINE PARTS (MGP).

85

9-2

INSPECTION AND MAINTENANCE

6OG-74E

PERIODIC MAINTENANCE SCHEDULE

A....Ad]ust. l....lnspect and correct or replace If necessary.

T....Tighten to specified torque. C....CIean.

R....Replace or change. O....Rotate

L....Lubrlcate.

Note:

This table includes services as scheduled up to 80,000 km mileage. Beyond 80,000 km, carry out the same services at the same intervals

respectively.

Interval: This interval should be judged

by odometer reading or months,

whichever comes first.
km (x 1,000)

months

ENGINE

1. Water pump drive belt (tension, wear)

2. Engine coolant (level, leakage)

3. Engine oil (API GRADE SF, SG, SH) & Oil filter

4. Cooling system hoses and connections (leakage, damage)

5. Engine bolts (All cylinder head and manifold fixings)

6. Engine mounting (loose, damage)

7. Valve clearance

8. Camshaft timing belt (damage, wear)

9. Exhaust system (noise, leakage or otherwise defective)

10. Positive crankcase ventilation System (Hoses, connections and valve;

IGNITION

1. Ignition wiring, (damage, deterioration)

2. Spark plugs (clean and adjust the gap)
FREE INSPECTIONS

1

1

A

I

R

I

-

-

-

_
5

6

I

I

I

I

-

-

A

-
10

12

I

I

R

I

T

T

-

-
PERIODIC MAINTENANCE SERVICE AT COST

20

24

I

R

R

I

-

-

A

I

Replace every 1,00,000 km

-

-

-
I

I

-

-
-

-

-

I
I

I

I

R
30

36

I

I

R

I

T

T

-

-

-

-

-

I
40

48

I

R

R

I

-

-

A

I

I

I

I

R
SO

60

I

I

R

I

T

T

-

-

-

-

-

I
60

72

R

R

R

I

-

-

A

I

I

I

I

R
70

84

A

I

R

I

T

T

-

-

-

-

-

I
80

96

I

R

R

I

-

-

A

I

I

I

I

R

9-3
86

60G-74E
INSPECTION AND MAINTENANCE

BATTERY

60G-09-022E

When installing the cover, make sure that it is

positioned so that it does not cover or foul the

air valve.
60G-09-038

Batteries produce flammable hydrogen

gas. Keep flames and sparks away from

the battery or an explosion may occur.

Never smoke when working in the

vicinity of the battery .

When checking or servicing the battery,

disconnect the negative cable. Be

careful not to cause a short circuit by

allowing metal objects to contact the

battery posts and the vehicle at the

same time.
To avoid harm to yourself or damage

to your vehicle or battery, follow the

jump starting instructions in the

EMERGENCY SERVICE section of this

manual if it is necessary to jump start

your vehicle.

The level of the battery solution must be kept

between the "UPPER" and the "LOWER" level

lines at all times. If the level is found to be

below the "LOWER" level line, add distilled

water to the "UPPER" level line. You should

periodically check the battery, battery

terminals, and battery holddown bracket for

corrosion. Remove corrosion using a stiff

brush and ammonia mixed with water, or

baking soda mixed with water. After removing

corrosion, rinse with clean water.

If your vehicle is not going to be driven for a

month or longer, disconnect the cable from

the negative terminal of the battery to help

prevent discharge.

105

9-22

INSPECTION AND MAINTENANCE

60G-74E

FUSES

60G-09-024E

©. Main fuse

®. Primary fuse (Lights)

®. Primary fuse (IG)

©. Radiator fan motor fuse

©. Primary fuse (A/C, HTR)

This vehicle has three types of fuses, as

described below:

Main Fuse - The main fuse takes current

directly from the battery.

Primary Fuses - These fuses are between the

main fuse and individual fuses, and are for

electrical load groups.

Individual Fuses - These fuses are in the fuse

box and for individual electrical circuits.
MAIN FUSE / PRIMARY FUSES

80A

60A

60A

30A

60A
All Electric Load

HEAD-R, HEAD-L, TAIL/DOME,

STOP/HORN, HAZARD

CIGAR/RADIO, I.G. COIL/

METER, WIPER/WASHER,

REAR DEF, TURN/BACK,

HEATER RELAY.

RADIATOR FAN MOTOR

A/C, HTR

Main Fuse and Primary Fuses

The main fuse and primary fuses are located

in the engine compartment. If the main fuse

blows, no electrical component will function.

If a primary fuse blows, no electrical

component in the corresponding load group

will function. When replacing the main fuse or

a primary fuse, use a genuine MARUTI

replacement.

If the main fuse or a primary fuse blows,

be sure to have your vehicle inspected

by an authorized MARUTI dealer.

Always use a genuine MARUTI

replacement. Never use a substitute

such as a wire even for a temporary

repair, or extensive electrical damage

and a fire can result.
60G-09-025E

Fuse Box

The fuse boxes are located in the engine

compartment and under the driver's side of

the dashboard.

To remove the fuse box cover under the

dashboard pull off the cover.

9-23
106

60G-74E
INSPECTION AND MAINTENANCE

60G-09-026

Always be sure to replace a blown fuse

with a fuse of the correct amperage.

Never use a substitute such as

aluminium foil or wire to replace a

blown fuse. If you replace a fuse and

the new one blows In a short period of

time, you may have a major electrical

problem. Have your vehicle Inspected

immediately by your MARUTI dealer.
60G-09-027E

NOTE:

Make sure that the fuse box always carries

spare fuses.
70F-07-04SE

60G-09-028E

107

9-24

INSPECTION AND MAINTENANCE

60G-74E

BULB REPLACEMENT

Light bulbs can be hot enough to

burn your finger right after being

turned off.This is true especially for

halogen headlight bulbs. Replace

the bulbs after they become cool

enough.

The headlight bulbs are filled with

pressurized halogen gas. They can

burst and injure you if they are hit

or dropped. Handle them carefully.

CAUTION

The oils from your skin may cause a

halogen bulb to overheat and burst

when the lights are on. Grasp a new

bulb with a clean cloth.

CAUTION

Frequent replacement of a bulb

indicates the need for an inspection of

the electrical system. This should be

carried out by your MARUTI dealer.
60G-09-029

Interior Light

Press down the lens by using a plain screw

driver covered with a soft cloth as shown. To

install it, simply push it back in.

The bulb can be removed by simply pulling it

out. When replacing the bulb, make sure that

the contact springs are holding the bulb

securely.
60G-09-030

NOTE:

If the air cleaner inlet duct (A) obstructs

replacement of the bulbs in the right headlight

housing, remove the duct (A).

After reinstalling the duct, make sure it is

secured in place

9-25
108

60G-74E

TABLE OF CONTENTS
MAINTENANCE SERVICE RECORD

WARRANTY POLICY

BEFORE DRIVING

STEERING COLUMN CONTROLS

INSTRUMENT PANEL

OTHER CONTROLS AND EQUIPMENT

OPERATING YOUR VEHICLE

DRIVING TIPS AND SAFE DRIVING

INSPECTION AND MAINTENANCE

EMERGENCY SERVICE

BODY WORK CARE

GENERAL INFORMATION

SPECIFICATIONS

SERVICE NETWORK

60G-74E

FOREWORD

This manual is an essential part of your

vehicle and should be kept with the vehicle

at all times. Please read this manual carefully

and review it from time to time. It contains

important information on safety, operation,

and maintenance. It is especially important

that this manual remain with the vehicle at

the time of resale. The next owner will need

this information also.

You are invited to avail the three free

inspection services as described in this

manual.Three free inspection coupons are

attached to this manual. Please show this

manual to your dealer when you take your

vehicle for any service.

To prolong the life of your vehicle and reduce

maintenance cost, the periodic maintenance

must be carried out according to the

"PERIODIC MAINTENANCE SCHEDULE"

described in "INSPECTION AND

MAINTENANCE" section of this manual.

Periodic maintenance is essential for

preventing trouble and accidents to ensure

your satisfaction and sefety.

Daily Inspection and Care as per "DAILY

INSPECTION CHECKLIST described in the

"INSPECTION AND MAINTENANCE" section

of this Manual is essential for prolonging the

operating lite of the vehicle and for safe driving.
MARUTI UDYOG LIMITED believes in

conservation and protection of Earth's

natural resources.

To that end, we encourage every vehicle

owner to recycle, trade in, or properly

dispose of, as appropriate, used motor oil,

coolant, and' other fluids; batteries; and

tyres.

MARUTI UDYOG LIMITED

All information in this manual is

based on the latest product

information available at the time of

publication. Due to improvements

or other changes, there may be

discrepancies between information

in this manual and your vehicle.

Maruti reserves the right to make

changes at any time without notice.

This vehicle may not comply with

standards or regulations of other

countries. Before attempting to

register this vehicle in any other

country, check all applicable

regulations and make any necessary

modifications.
IMPORTANT

WARNING/CAUTION/NOTE

Please read this manual and follow its

instructions carefully. To emphasise special

information, the words WARNING,

CAUTION, and NOTE have special

meanings. Information following these signal

words should be carefully reviewed.

WARNING

The personal safety of the driver,

passengers, or by standers may be

involved. Disregarding this information

could result in their injury or death.

CAUTION

These instructions point out special

service procedures or precautions that

must be followed to avoid damaging

the vehicle.

NOTE:

This provides special information to make

maintenance easier or important instructions

clearer.

0-1
3

60G-74E

MODIFICATION WARNING

60G-00-004

The circle with a slash in this manual

means "Don't do this" or "Don't let this

happen".
Do not modify this vehicle. Modification

could adversely affect safety, handling,

performance, or durability and may

contravene regulations. In addition,

damage or performance problems

resulting from modification may not be

covered under warranty.
Improper installation of mobile

communication equipment such as

cellular talephones or CB (Citizen's

Band) radios may cause electronic

interference with your vehicle's ignition

system, resulting in vehicle

performance problems. Consult your

MARUTI dealer or qualified service

technician for advice on installing such

mobile communication equipment.

0-2
Copying, quoting or reproduction of any

part of this manual is not permitted without

explicit approval by MARUTI UDYOG

LIMITED.

60G-74E

WARRANTY POLICY

WARRANTY POLICY

Maruti Udyog Limited (hereinafter called "Maruti"), warrants that each

new Maruti vehicle distributed in India by Maruti and sold by an

authorised Maruti dealer will be free, under normal use and service,

from any defects in material and workmanship at the time of

manufacture SUBJECT TO THE FOLLOWING TERMS AND

CONDITIONS:

(1) Qualification:

To qualify for this warranty:

(a) The Maruti vehicle must be delivered by Maruti authorised

dealer and set-up, serviced by Maruti authorised dealer/

service station.

(b) The warranty registration card in respect of each vehicle

must be completed by the dealer at the time of delivery

of the vehicle and dealer should retain the same.

(2) Term:

The term of the warranty shall be twenty four (24) months

or 40,000 kilometers (whichever occurs first) from the date

of delivery to the first owner.

(3) Maruti's Warranty Obligation:

If any defect(s) should be found in a Maruti vehicle within the

term stipulated above, Maruti's only obligation is to repair or

replace at its sole discretion any part shown to be defective,

with a new part or the equivalent at no cost to the owner for

parts or labour, when Maruti acknowledges that such a defect

is attributable to faulty material or workmanship at the time of

manufacture. The owner is responsible of any repair or

replacements which are not covered by this warranty.
(4) Limitation:

This warranty shall not apply to:

(a) normal maintenance service required other than the three

free services, including without limitation, oil and fluid

changes, headlight aiming, fastener retightening, wheel

balancing, wheelalignment and tyre rotation, cleaning of

injectors, adjustments of carburettor, ignition timing, clutch

and valve clearance.

(b) the replacement of normal wear parts including without

limitation, bulbs, battery, tyres and tubes, spark plugs, belts,

hoses, filters, wiper blades, brushes, contact points, fuses,

clutch disc, brake shoes, brake pads, cable and all rubber

parts (except oil seal and glass run).

(c) any vehicle which has been used for competition or racing.

(d) any repairs or replacement required as a result of accidents

or collision.

(e) any defects caused by misuse, negligence, abnormal use or

insufficient care.

(f) any vehicle which has been modified or altered, including

without limitation, the installation of performance accessories.

(g) any vehicle on which parts or accessories not approved by

Maruti have been used.

(h) any vehicle which has not been operated in accordance with

the operating instructions in the Maruti Owner's Manual,

(i) any vehicle which has not received, during the warranty

term, the service inspections prescribed in the Maruti

Owner's Manual.

G) any vehicle which has been assembled, disassembled,

adjusted or repaired by other than an Maruti authorised

2-1