warning SUZUKI GRAND VITARA 2002 2.G Service Workshop Manual
[x] Cancel search | Manufacturer: SUZUKI, Model Year: 2002, Model line: GRAND VITARA, Model: SUZUKI GRAND VITARA 2002 2.GPages: 801, PDF Size: 12.15 MB
Page 783 of 801
YH4
GRAND
VITARA
AIR BAG SYSTEM 10B-77
1. Slit on workbench
2. Workbench vise
3. Lower mounting bracket
ALWAYS CARRY AIR BAG (INFLATOR) MODULE
WITH TRIM COVER (AIR BAG OPENING) AWAY
FROM BODY.
ALWAYS PLACE AIR BAG (INFLATOR) MODULE
ON WORKBENCH WITH TRIM COVER (AIR BAG
OPENING) UP, AWAY FROM LOOSE OBJECTS.WARNING:
Always carry a live air bag (inflator) module with trim
cover away from you.
When storing a live air bag (inflator) module or when
leaving a live air bag (inflator) module unattended on
a bench or other surface, always face the bag and trim
cover up and away from the surface. As the live pas-
senger air bag (inflator) module must be placed with
its bag (trim cover) facing up, place it or the work-
bench with a slit or use the workbench vise to hold it
securely at its lower mounting bracket.
This is necessary so that a free space is provided to
allow the air bag to expand in the unlikely event of ac-
cidental deployment.
Failure to follow procedures may result in personal inju-
ry.
23) Temporarily store the air bag (inflator) module with its vinyl trim
cover facing up, away from the surface upon which it rests. Re-
fer to ªService Precautionsº in this section for details.
24) Contact your local distributor for further assistance.
Page 784 of 801
YH4
GRAND
VITARA
10B-78 AIR BAG SYSTEM
DEPLOYMENT INSIDE VEHICLE
Use this procedure when scrapping the entire vehicle including the driver and passenger air bag (inflator) modules.
CAUTION:
When vehicle itself will be used again, deploy the air bag outside vehicle according to ªDeployment
Outside Vehicleº, for deploying it inside will cause the instrument panel, glove box and their vicinity
to be deformed.
Failure to observe this CAUTION may require unneeded vehicle inspection and repair.
WARNING:
Following precautions must be observed for this work. Failure to observe any of them may result in
personal injury.
To avoid an accidental deployment, this work should be performed by no more than one person.
The procedure should be followed strictly as described here.
Be sure to read ªService Precautionsº for the air bag (inflator) module beforehand.
Never connect deployment harness to any power source before connecting deployment harness to
the air bag (inflator) module. Deployment harness shall remain shorted and not be connected to a
power source until the air bag is to be deployed.
The air bag (inflator) module will immediately deploy the air bag when a power source is connected
to it. Wear safety glasses throughout this entire deployment and disposal procedure.
Wear suitable ear protection when deploying air bag. Also, advise those who are in the area close to
deployment site to wear suitable ear protection.
Do not deploy driver and passenger air bag (inflator) modules at the same time.
1) Turn ignition switch to ªLOCKº, remove key and put on safety
glasses.
2) Remove all loose objects from front seats and instrument panel.
3) [For driver air bag (inflator) module]
Disconnect contact coil connector (yellow connector) located
near the base of the steering column.
ii) Release locking of lock lever.
ii) After unlocked, disconnect to connector.
[For passenger air bag (inflator) module]
Remove glove box from instrument panel and disconnect pas-
senger air bag (inflator) module connector (yellow connector).
ii) Release locking of lock lever.
ii) After unlocked, disconnect to connector.
Page 785 of 801
YH4
GRAND
VITARA
1. Shorted
For driver air bag (inflator) module
1. Short deployment harness leads
AIR BAG SYSTEM 10B-79
4) Confirm that each air bag (inflator) module is securely mounted.
5) Check that there is no open/short or damage in special tool (de-
ployment harness). If any faulty condition is found, do not use it
and be sure to use new deployment harness.
Special Tool
(A): 09932-75030
6) Short the two deployment harness leads together by fully seat-
ing one banana plug into the other.
WARNING:
Deployment wires shall remain shorted and not be con-
nected to a power source until the air bag is to be
deployed.
Special Tool
(A): 09932-75030
7) Connect deployment harness connector to air bag (inflator)
module (driver or passenger) and lock connector with lock lever.
Special Tool
(A): 09932-75030
Page 786 of 801
YH4
GRAND
VITARA
Driver side for left hand steering vehicle
Driver side for right hand steering vehicle
1. Stretch deployment harness to its full length
10 m (33 ft).
2. Drop cloth, blanket or similar item2
10B-80 AIR BAG SYSTEM
8) Route deployment harness out the vehicle.
9) Verify that the inside of the vehicle and the area surrounding
the vehicle are clear of all people and loose or flammable ob-
jects.
10) Stretch the deployment harness to its full length 10 m (33 ft).
11) Place a power source near the shorted end of the deployment
harness. Recommended application: 12 Volts minimum, 2
amps minimum. A vehicle battery is suggested.
12) Completely cover windshield area and front door window
openings with a drop cloth, blanket to similar item. This reduces
the possibility of injury due to possible fragmentation of the ve-
hicle's glass or interior.
13) Notify all people in the immediate area that you intend to deploy
the air bag (inflator) module.
NOTE:
When the air bag deploys, the rapid gas expansion will
create a substantial report. Wear suitable ear protection.
Notify all people in the immediate area that you intend to
deploy the air bag (inflator) module and suitable ear
protection should be worn.
After the air bag (inflator) module has been deployed, the
surface of the air bag may contain a powdery residue.
This powder consists primarily of cornstarch (used to lu-
bricate the bag as it inflates) and byproducts of the
chemical reaction.
WARNING:
Safety precautions must be observed when handling a
deployed air bag (inflator) module.
After deployment, the metal surfaces of the air bag (infla-
tor) module will be very hot. Do not touch the metal areas
of the air bag (inflator) module for about 30 minutes after
deployment.
Do not apply water, oil, etc. to deployed air bag (inflator)
module.
If the deployed air bag (inflator) module must be moved
before it is cool, wear gloves and handle by the air bag or
vinyl trim.
Failure to follow procedures may result in fire or personal
injury.
Page 788 of 801
YH4
GRAND
VITARA
ALWAYS CARRY AIR BAG (INFLATOR) MODULE
WITH TRIM COVER (AIR BAG OPENING) AWAY
FROM BODY.
ALWAYS PLACE AIR BAG (INFLATOR) MODULE
ON WORKBENCH WITH TRIM COVER (AIR BAG
OPENING) UP, AWAY FROM LOOSE OBJECTS.
1. Slit on workbench
2. Workbench vise
3. Lower mounting bracket
10B-82 AIR BAG SYSTEM
21) In the unlikely event that either or both of the air bag (inflator)
modules proceed immediately with Steps 23) through 25). If
the air bag (inflator) module did deploy, proceed with Steps 22).
22) With air bags deployed the vehicle may be scrapped in the
same manner as a non-air bag system equipped vehicle.
23) Remove the undeployed air bag (inflator) module(s) from the
vehicle. For driver air bag (inflator) module refer to SECTION
3C1, for passenger air bag (inflator) module refer to ªOn-Ve-
hicle Serviceº in this section.
WARNING:
Always carry a live air bag (inflator) module with trim
cover away from you.
When storing a live air bag (inflator) module or when
leaving a live air bag (inflator) module unattended on
a bench or other surface, always face the bag up, away
from the surface.
This is necessary so that a free space is provided to
allow the air bag to expand in the unlikely event of ac-
cidental deployment.
Failure to follow procedures could result in personal in-
jury.
24) Temporarily store the air bag (inflator) module with its vinyl trim
cover facing up, away from the surface upon which it rests. Re-
fer to ªService Precautionsº in this section for details.
25) Contact your local distributor for further assistance.
Page 789 of 801
YH4
GRAND
VITARA
AIR BAG SYSTEM 10B-83
SEAT BELT PRETENSIONERS DISPOSAL
WARNING:
Failure to follow proper seat belt pretensioner (retractor assembly) disposal procedures can result in
pretensioner activation which may cause personal injury. Inactivated seat belt pretensioner must not
be disposed of through normal refuse channels.
The inactivated seat belt pretensioner contain substances that can cause severe illness or personal
injury if the sealed container is damaged during disposal.
Do not dispose of the live (inactivated) seat belt pretensioners.
The method employed depends upon the final disposition of the particular vehicle, as noted in ªActivation Outside
Vehicleº and ªActivation Inside Vehicleº in this section.
Activation Outside Vehicle disposing of the seat belt pretension(s) only (i.e., the vehicle itself will be used. . . . . . . .
again).
Activation Inside Vehicle scrapping the entire vehicle including the seat belt pretensioners.. . . . . . . . . .
ACTIVATION OUTSIDE VEHICLE
Use this procedure when the vehicle itself is used again (only the seat belt pretensioner(s) are disposed of).
WARNING:
Following precautions must be observed for this work. Failure to observe any of them may result in
personal injury.
To avoid an accidental activation, this work should be performed by no more than one person.
The procedure should be followed strictly as described here.
Be sure to read ªService Precautionsº in this section for the seat belt pretensioner beforehand.
Never connect deployment harness to any power source before connecting deployment harness to
the seat belt pretensioner. Deployment harness shall remain shorted and not be connected to a power
source until the pretensioner is to be activated.
The seat belt pretensioner will immediately activate the pretensioner when a power source is con-
nected to it. Wear safety glasses throughout this entire activation and disposal procedure.
Wear suitable ear protection when activating pretensioner. Also, advise those who are in the area
close to activation site to wear suitable ear protection.
Do not activate driver and passenger seat belt pretensioners at the same time.
The following procedure requires use of special tools (deployment harness). Do not attempt procedure without it.
Page 790 of 801
YH4
GRAND
VITARA
1. Shorted
1. Exhaust hole
1 1
NG
10B-84 AIR BAG SYSTEM
1) Turn ignition switch to ªLOCKº, remove key and put on safety
glasses.
2) Check that there is no open, short or damage in special tool (de-
ployment harness). If any faulty is found, do not use it and be
sure to use new deployment harness.
Special Tool
(A): 09932-75030
3) Short the two deployment harness leads together by fully seat-
ing one banana plug into the other.
WARNING:
Deployment harness shall remain shorted and not be
connected to a power source until the pretensioner is to
be activated.
Special Tool
(A): 09932-75030
4) Remove driver or passenger seat belt pretensioner(s) and seat
belt pretensioner harness(s) from vehicle, referring to SECTION
10A.
WARNING:
For handling and storage of a live seat belt pretension-
er, select a place where the ambient temperature below
65C (150F), without high humidity and away from
electric noise.
Never carry the seat belt pretensioner by the wires or
connector on the underside of the pretensioner.
When placing a live seat belt pretensioner on the work-
bench or some place like that, be sure not to lay with its
exhaust hole provided side facing down. it is also pro-
hibited to put something on its face with an exhaust
hole or to put a seat belt pretensioner on top of another.
Otherwise, personal injury may result.
5) Temporarily place seat belt pretensioner on the workbench ac-
cording to above WARNING.
Page 791 of 801
YH4
GRAND
VITARA
1. Seat belt pretensioner (retractor assembly)
2. Webbing
3. 185 cm (6 ft) of clearance
4. Exhaust hole
1. Stretch deployment harness to full length 10 m (33 ft).
2. Connect connectors.
3. Power source (12V vehicle battery)
4. Short the two deployment harness leads.
5. Seat belt pretensioner harness
4
AIR BAG SYSTEM 10B-85
6) Pull out the webbing fully as shown at the left and cut it at the
root of the pretensioner (retractor assembly) as shown in the
figure.
WARNING:
As the drum of the retractor assembly turns very quick-
ly as soon as the webbing is cut, fix the retractor assem-
bly with a vise on the workbench and keep your hands
and fingers away from it when cutting the webbing.
7) Clear a space on the ground about 185 cm (6 ft) in diameter
where the seat belt pretensioner is to be activated. A paved,
outdoor location where there is no activity is preferred. If an out-
door location is not available, a space on the shop floor where
there is no activity and sufficient ventilation is recommended.
Ensure no loose or flammable objects are within the activation
area.
8) Place the seat belt pretensioner as shown in the figure on the
ground in the space just cleared.
9) Stretch the deployment harness from the seat belt pretension-
er to its full length 10 m (33 ft).
10) Place a power source near the shorted end of the deployment
harness. Recommended application: 12 Volts minimum, 2
amps minimum. A vehicle battery is suggested.
11) Verify that the area around the seat belt pretensioner is clear
of all people and loose or flammable objects.
12) Verify that the seat belt pretensioner is placed as shown in the
figure on the ground in the space just cleared.
13) Connect the seat belt pretensioner harness to the deployment
harness connector and lock the connector with lock lever.
Special Tool
(A): 09932-75030
Page 792 of 801
YH4
GRAND
VITARA
1. Connect one banana plug to positive terminal of power
source (12V vehicle battery) and then the other to
negative terminal to immediately activate.
2. Short to two deployment harness leads.
10B-86 AIR BAG SYSTEM
14) Notify all people in the immediate area that you intend to acti-
vate the seat belt pretensioner.
NOTE:
When the pretensioner activates, the rapid gas expan-
sion will create a substantial report. Wear suitable ear
protection. Notify all people in the immediate area that
you intend to activate the seat belt pretensioner and suit-
able ear protection should be worn.
When the pretensioner activates, the seat belt preten-
sioner may jump about 30 cm (1 ft) vertically. This is a
normal reaction of the seat belt pretensioner to the force
of the rapid gas expansion inside the pretensioner.
WARNING:
Safety precautions must be observed when handling
an activated seat belt pretensioner.
After activation, the metal surfaces of the seat belt
pretensioner will be very hot. Do not touch the metal
areas of the seat belt pretensioner for about 30 min-
utes after activation.
Do not place the activated seat belt pretensioner
near any flammable objects.
Do not apply water, oil, etc. to the activated seat belt
pretensioner.
If the activated seat belt pretensioner must be
moved before it is cool, wear gloves and handle it by
using nonmetal material.
Failure to follow procedures may result in fire or per-
sonal injury.
15) Separate the two banana plugs on the deployment harness.
16) Connect the deployment harness to the power source (12V ve-
hicle battery) to immediately activate the pretensioner.
17) Disconnect the deployment harness from power source (12V
vehicle battery) and short the two deployment harness leads
together by fully seating one banana plug into the other.
Page 794 of 801
YH4
GRAND
VITARA
1. Exhaust hole
1 1
NG
10B-88 AIR BAG SYSTEM
NOTE:
The remaining steps are to be followed in the unlikely event
that the seat belt pretensioner did not activate after following
these procedures.
23) Ensure that the deployment harness has been disconnected
from the power source and that its two banana plugs have been
shorted together by fully seating one banana plug into the oth-
er.
24) Disconnect the deployment harness from the seat belt preten-
sioner.
WARNING:
For handling and storage of a live seat belt pretensioner,
select a place where the ambient temperature below 65C
(150F), without high humidity and away from electric
noise.
Never carry the seat belt pretensioner by the wires or con-
nector on the underside of the pretensioner.
When placing a live seat belt pretensioner on the work-
bench or some place like that, be sure not to lay it with its
exhaust hole provided side facing down. It is also prohib-
ited to put something on its face with an exhaust hole or
to put a seat belt pretensioner on top of another.
Otherwise, personal injury may result.
25) Temporarily store the seat belt pretensioner. At that time, be
sure NOT to face its exhaust hole provided side down. It must
face up. Refer to ªService Precautionsº in this section for detail.
26) Contact your local distributor for further assistance.