lock SUZUKI MARUTI 2005 1.G User Guide

Downloaded from www.Manualslib.com manuals search engine 2283K
BEFORE DRIVING
4-10e) Press Lock button on Key, after a sin-
gle chirp enter the First digit (with in 1-
9) by pressing Valet switch (for e.g. to
enter 2 press and release Valet switch
two times).
f) Press Lock button on Key, after two
chirp enter the Second digit (with in 1-
9) by pressing Valet switch.
g) Press Lock button on Key, after 3-chirps
enter the Third digit (with in 1-9) by
Pressing Valet switch.
h) Press Lock button on Key, after 4-chirps
enter the Fourth digit (with in 1-9) by
pressing Valet switch.
Emergency Disarm by personalised pin
code
The Personalised 4- Digit Pin Code acts as
a secret Key, to Emergency Disarm the
vehicle.
a) Turn the IGN ON, OFF and then ON.
b) Enter the First digit (for e. g. to enter 2
press and release Valet switch twice)
c) Turn the IGN OFF then ON.
d) Enter the Second digit.
e) Turn the IGN OFF and then ON.
f) Enter the Third Digit.
g) Turn the IGN OFF and then ON
h) Enter the Last Digit.
i) Turn the IGN OFF and then ON.
The vehicle will get disarmed.

Downloaded from www.Manualslib.com manuals search engine 2383K
BEFORE DRIVING
4-11
SYMPTOMS
Transmitter can't activate or deactivate the
center lock system or alarm
Control distance of the transmitter becomes
nearer (less than 10m)
It is difficult to activate or deactivate the
system in certain area using the transmitter.
Open door(s), front bonnet not trigger the
alarm.
Siren does not sound when alarm is
triggered.Troubleshooting
PROBABLE CAUSES
1. Battery of the transmitter is weak.
2. Transmitter is exposed to water or it is
wet.
3. In-line supply fuse for controller is blown
in the vehicle.
4. In case if any door is open or door
sensor is shorted with the body ground,
remote will not activate the central
locking/ alarm system.
1. Battery of the transmitter is weak.
2. Strong RF interference. (e.g. Radio
Towers, High Voltage Transmission line
near by)
1. The strong interference caused by
excessive RF activity in a particular area
1. The contact point of the door(s), front
bonnet of rear boot switch is faulty.
2. The connection of door(s), front bonnet
of rear boot switch is loose.
1. The connection of the siren wire is
loose.
2. Siren is faulty.REMEDIES
1. Replace the battery.
2. Dry the transmitter and fine-tuning may
be necessary.
3. Replate the fuse.
4. Check if all doors are properly closed
and door switch functioning is O.K.
1. Replace the battery.
2. Drive the vehicle away from the parti-
cular spot and re-test the control dis-
tance.
1. The interference is temporary and only
while the vehicle is in that area.
1. Replace the defective Switch.
2. Make proper connection.
1. Make proper connection.
2. Change the siren.

Downloaded from www.Manualslib.com manuals search engine 2483K
BEFORE DRIVING
4-12WindowsManual Window Control
(if equipped)Raise or lower the door windows by turning
the handle located on the door panel.Electric Window Controls
(if equipped)The electric windows can only be operated
when the ignition switch is in the “ON” position.
Driver’s door
83K-02-02183K-02-022
The driver’s door has switches (1), (2), (3),
(4) to operate the driver’s window, the front
passenger’s window, the rear left window
and the rear right window, respectively.
Passenger’s door (if equipped)
The passenger’s door has a switch (6) to
operate that passenger’s window.
83K-02-023
EXAMPLE
EXAMPLEEXAMPLE
83K-02-024
To open a window, push the top part of the
switch and to close the window, lift up the
top part of the switch.
The driver’s window has an “auto-down”
feature for added convenience (at toll
booths or drive-through restaurants, for
example). This means you can open the
window without holding the window switch
in the “Down” position. Press the driver’s
window switch completely down and release
it. To stop the window before it reaches the
bottom, pull the switch up briefly.
Lock switch (if equipped)
The driver’s door also has a lock switch (5)
for the passenger’s windows. When you
push in the lock switch, the passenger’s
windows can not be raised or lowered by
operating any of the switches (2), (3), (4)

Downloaded from www.Manualslib.com manuals search engine 2583K
BEFORE DRIVING
4-13
or (6). To restore normal operation, release
the lock switch by pushing again.
w ww w
w WARNING
You should always lock the passen-
ger’s window operation when there
are children in the vehicle. Children
can be seriously injured if they get
part of their body caught by the
window during operation.
To avoid injuring an occupant by
window entrapment, be sure no part
of the occupant’s body such as
hands or head is in the path of the
electric windows when closing them.
Always remove the ignition key
when leaving the vehicle even if a
short time. Also do not leave chil-
dren alone in a parked vehicle.
Unattended children could use the
electric window switches and get
trapped by the window.MirrorsInside Rearview Mirror
83K-02-026
83K-02-026A
w ww w
w WARNING

selector set to the day position.

necessary to reduce glare from the
headlights of vehicles behind you.
Be aware that in this position you
may not be able to see some
objects that could be seen in the
day position.You can adjust the outside rearview mirrors
by hand with the knob (1) located on the
driver’s or front passenger’s door panel (If
equipped).
83K-02-027
Outside Rearview MirrorsTYPE-1
83K-02-027A
TYPE-2 Electric Mirrors (if equipped)The switch to control the electric mirrors is
located on the driver’s door panel. You can
adjust the mirrors when the ignition switch
is in the “ACC” or “ON” position. To adjust
the mirrors: For Type 1 mirrors you can adjust the
inside rearview mirror by hand so as to
see the rear of your vehicle in the mirror.
For Type 2 mirrors adjust the mirror,set the
selector tab (1) to the day position,then
move the mirror up, down or sideways by
hand to obtain the best view. When driving
at night, you can move the selector tab to
the night position to reduce glare from the
headlights of vehicles behind you.
TYPE-1TYPE-2

Downloaded from www.Manualslib.com manuals search engine 2783K
BEFORE DRIVING
4-15
w ww w
w WARNING
Never drive the vehicle with the
head restraints removed.
Do not attempt to adjust the head
restraint while driving.
83K-02-031
To adjust the seatback angle of front seats,
pull up the lever on the outboard side of
the seat, move the seatback to the desired
position, and release the lever to lock the
seatback in place.Adjustable Head Restraints
(if equipped)Head restraints are designed to help reduce
the risk of neck injuries in the case of an
accident.
NOTE:
It may be necessary to recline the seatback
to provide enough overhead clearance to
remove the head restraint.
83K-02-032
Adjust the head restraint to the position
which places the center of the head restraint
closest to the top of your ears. If this is not
possible for very tall passengers, adjust the
head restraint as high as possible.
EXAMPLE
Seat Height Adjuster (if equipped)If the driver’s seat is equipped with a seat
height adjuster lever on the outboard side
of the seat, raise or lower the seat by pull-
ing up or down the adjuster lever.Adjusting Seatbacks
83K-02-030
w ww w
w WARNING
All seatbacks should always be in an
upright position when driving, or seat
belt effectiveness may be reduced.
Seat belts are designed to offer maxi-
mum protection when seatbacks are in
the upright position.EXAMPLE

Downloaded from www.Manualslib.com manuals search engine 2883K
BEFORE DRIVING
4-16
Rear SeatsAdjustable Head Restraints
(if equipped)
83K-02-034
To raise the rear head restraint, pull upward
on the restraint until it clicks. To lower the
restraint, push down on the restraint while
holding in the lock lever. If a head restraint
is required to be removed (for cleaning,
replacement, etc.), push in the lock lever
and pull the head restraint all the way out.
When installing a child restraint system,
raise the head restraint to the most upper
position.
Folding Rear Seats (if equipped)The rear seat(s) of your vehicle can be
folded forward to provide additional cargo
space.
To fold the rear seats forward:
1) Hook the webbing and the latch plate of
the outboard lap-shoulder belts in the
belt hangers.
83K-02-035
CAUTION
When you move a seatback, make
sure both the latch plate and the
belt webbing are hooked in the seat
belt hangers so the seat belts are
not caught by the seatback, seat
hinge, or seat latch. This helps pre-
vent damage to the belt system.
V
Front
To raise the front head restraint, pull
upward on the restraint until it clicks. To
lower the restraint, push down on the
restraint while holding in the lock lever. If
a head restraint must be removed (for
cleaning, replacement, etc.), push in the
lock lever and pull the head restraint all the
way out.
83K-02-033
EXAMPLE

Downloaded from www.Manualslib.com manuals search engine 2983K
BEFORE DRIVING
4-17
NOTICE
After folding the rear seatback for-
ward, do not allow any foreign mate-
rial to enter the lock opening. This
may cause damage to the inside of
the lock and prevent the seatback
from being locked securely.
w ww w
w WARNING
If you need to carry cargo in the pas-
senger compartment with the rear seat
back folded forward, be sure to secure
the cargo or it may be thrown about,
causing injury. Never pile cargo higher
than the seatbacks.
To return the seat to the normal position,
follow the procedure below.
When returning the rear seatback to
the normal position, be careful that
your finger is not caught between the
lock and the striker.
When returning the rear seatback to
the normal position, make sure that
there is nothing around the striker.
Any foreign materials prevent the
seatback from being locked securely.
83K-02-037
Raise the seatback until it locks into place.
After returning the seat, try moving the
seatback to make sure they are securely
latched.
Do not put your hand into the rear
seatback lock opening, or your finger
may get caught and be injured.
When returning the rear seatback to
the normal position, do not allow
any foreign material to enter the
lock opening. This may prevent the
seatback from being locked
securely.
NOTICE
EXAMPLE
When you hook the belt webbing
and latch plate into the seat belt
hanger, make sure the latch plate is
on the obverse side of the belt web-
bing as shown in the illustration.
Make sure the belt webbing is not
twisted.
CAUTION
2) Lower the adjustable head restraint fully.
83K-02-036
3) For the split seat (if equipped), pull the
release lever on the top of each split
seat, and fold the seatbacks forward.
For the bench seat, pull the both release
levers on the top of the bench seat
together, and fold the seatback forward.EXAMPLEV VV V
V
CAUTIONw ww w
w WARNING
CAUTION
V VV V
V

Downloaded from www.Manualslib.com manuals search engine 3083K
BEFORE DRIVING
4-18
w ww w
w WARNING
An air bag supplements, or adds to,
the frontal crash protection offered by
seat belts. The driver and all pas-
sengers must be properly restrained
by wearing seat belts at all times,
whether or not an air bag is mounted
at their seating position, to minimize
the risk of severe injury or death in
the event of a crash.
83K-02-039
w ww w
w WARNING
Never allow persons to ride in the
cargo area of a vehicle. In the event
of an accident, there is a much
greater risk of injury for persons
who are not riding in a seat with
their seat belt securely fastened.
Seat belts should always be
adjusted as follows:
– the lap portion of the belt should
be worn low across the pelvis, not
across the waist.
– the shoulder straps should be
worn on the outside shoulder
only, and never under the arm.
– the shoulder straps should be
away from your face and neck,
but not falling off your shoulder.
83K-02-040
NOTICE
When returning the rear seatback to
the normal position, be sure to
handle it carefully by hand to avoid
any damage to the lock itself. Do
not push it by using some material
or by applying excessive force.
As the lock is designed exclusively
for securing the rear seatback, do
not use it for any other purpose.
Incorrect use of it may cause
damage to the inside of the lock
and prevent the seatback from being
locked securely.Seat Belts and Child Restraint
Systems
w ww w
w WARNING
Wear Your Seat Belts at All Times.
83K-02-038
V VV V
V

Downloaded from www.Manualslib.com manuals search engine 3283K
BEFORE DRIVING
4-20
83K-02-043
To reduce the risk of sliding under the belt
during a collision, position the lap portion
of the belt across your lap as low on your
hips as possible and adjust it to a snug fit
by pulling the shoulder portion of the belt
upward through the latch plate. The length
of the diagonal shoulder strap adjusts itself
to allow freedom of movement.All Seat Belts Except Rear Centre
83K-02-044
To fasten the seat belt, sit up straight and
well back in the seat, pull the latch plate
attached to the seat belt across your body
and press it into the buckle until you hear
a “click”.
Lap-Shoulder BeltEmergency Locking Retractor (ELR) (if
equipped)
The seat belt has an emergency locking
retractor (ELR), which is designed to lock
the seat belt only during a sudden stop or
impact. It also may lock if you pull the belt
across your body very quickly. If this hap-
pens, let the belt go back to unlock it, then
pull the belt across your body more slowly.
Safety reminder
83K-02-042

Downloaded from www.Manualslib.com manuals search engine 3383K
BEFORE DRIVING
4-21
NOTE:
The word “CENTER” is molded into the
buckle for the rear center belt. The buckles
are designed so a latch plate can not be
inserted into the wrong buckle.Driver’s Seat Belt Reminder (if
equipped)
83K-02-047
When the driver doesn’t buckle his or her
seat belt, the driver’s seat belt reminder light
in the instrument cluster will come on or
blink, as a reminder to the driver to buckle
his or her seat belt.
The reminder will be automatically cancel
when the driver’s seat belt is buckled or the
ignition switch is turned off.
Shoulder Anchor Height Adjuster (if
equipped)Adjust the shoulder anchor height so that
the shoulder belt rides on the center of the
outboard shoulder. To adjust the shoulder
anchor height, slide the anchor up or down
while pushing the lock button. After adjust-
ment, make sure that the anchor is securely
locked.
83K-02-048
w ww w
w WARNING
It is absolutely essential that the
driver and passengers wear their seat
belts at all times. Persons who are not
wearing seat belts have a much
greater risk of injury if an accident
occurs. Make a regular habit of buck-
ling your seat belt before putting the
key in the ignition.
83K-02-045
To unfasten the belt, push the red “PRESS”
button on the buckle and allow the belt to
retract.
83K-02-046
EXAMPLE