Isc SUZUKI SWIFT 2000 1.G SF310 Service Service Manual

ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10) 6-35
CONNECTOR “C02”
TER-
MINALWIRE
COLORCIRCUITSTANDARD
VOLTAGECONDITION
1BECM (PCM) ground––
2W/BlPower source10 – 14 VIgnition switch ON
3—Blank——
4—Blank——
5—Blank——
6—Blank——
7R/GEVAP canister purge valve10 – 14 VIgnition switch ON
8G/OrShift solenoid B (A / T)
0 VIgnition switch ON, selector lever at “P”
range
8G/OrShift solenoid-B (A / T)
10 – 14 VIgnition switch ON, selector lever at “D”
range
9G/WShift solenoid A (A / T)
0 VIgnition switch ON, selector lever at “P”
range
9G/WShift solenoid-A (A / T)
10 – 14 VIgnition switch ON, selector lever at “D”
range
10OrIgniter (IGT)——
11Gr / YISC actuator——
12Y/BFuel injector10 – 14 VIgnition switch ON
13B/BlGround for injector——
14WPower source for back-up10 – 14 VIgnition switch ON and OFF
15W/BlPower source10 – 14 VIgnition switch ON
16Gr / BISC actuator relay0.3 – 1.0 VIgnition switch ON
17V/YMalfunction indicator lamp0.2 – 2.0 VIgnition switch ON17V/YMalfunction indicator lamp10 – 14 VWhen engine running
18V/GImmobilizer indicator lamp0.2 – 2.0 VIgnition switch ON18V/GImmobilizer indicator lamp10 – 14 VWhen engine running at idle
19Lg / BHeater of H02S-210 – 14 VIgnition switch ON
20BlRadiator fan control relay
10 – 14 VIgnition switch ON, Engine coolant
temp: Below 91.5C (197F)
20BlRadiator fan control relay
0.3 – 1.0 VIgnition switch ON, Engine coolant
temp: 96.0C (205F) or higher
21P/WFuelpumprelay0.3 – 1.3 VFor 2 seconds after ignition switch ON21P/WFuel pump relay10 – 14 VAfter the above time
22Bl / BMain relay0.4 – 1.5 VIgnition switch ON
23–Blank——
24Gr / RISC actuator——
25Y/REFE heater relay10 – 14 VIgnition switch ON
26B/RGround for injector——

6-36 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
CONNECTOR “C01”
TER-
MINALWIRE
COLORCIRCUITSTANDARD
VOLTAGECONDITION
1LgPower source for sensor4.75 – 5.25 VIgnition switch ON
2OrCamshaft position sensor (+)——
3W/BCrankshaft position sensor
(+)——
4Gr / GClosed throttle position switch
0 – 1 V
Ignition switch ON, ISC actuator
plunger is in contact with throttle lever
screw
4Gr / G(In ISC actuator)
4 – 6 V
Ignition switch ON
Plunger is apart from throttle lever
screw
5Lg / RManifold absolute pressure
sensor3.3 – 4.0 V
Ignition switch ON
Barometric pressure: 100 kPa,
760 mmHg
6Lg / WThrottle position sensor
0.2 – 1.0 V
Ignition switch ON, when clearance
between throttle lever and throttle stop
screw is less than 0.35 mm (0.014 in.)
2.8 – 4.8 VIgnition switch ON
Throttle valve at full open position
7Gr / WEngine coolant temp. sensor0.55 – 0.95 VIgnition switch ON
Engine coolant temp.: 80C (176F)
8P/BHeater of H02S-110 – 14 VIgnition switch ON
9GGround for sensors——
10WCamshaft position sensor (–)——
11W/RCrankshaft position sensor
(+)——
12W/BEFE heater monitor0 – 1 VHeater relay OFF12W/BEFE heater monitor10 – 14 VHeater relay ON
13RHeated oxygen sensor-1Refer to DTC flow chart
14GrIntake air temp. sensor2.0 – 2.7 V
Ignition switch ON
Sensor ambient temp.
(Intake air temp): 20C (68F)
10 – 14 VIgnition switch ON
15Bl / WPower steering pressure
switch (If equipped)
0 – 1 V
With engine running at idle speed,
turning steering wheel to the right or left
as far as it stops, repeating it a few
times
16B/YEngine start switch6 – 12 VWhile engine cranking16B/Yg
(Engine start signal)0 – 1 VOther than above

6-38 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
1 2
1. ECM (PCM)
coupler disconnected
2. Ohmmeter
RESISTANCE CHECK
1) Disconnect ECM (PCM) couplers from ECM (PCM) with ignition
switch OFF.
CAUTION:
Never touch terminals of ECM (PCM) itself or connect
voltmeter or ohmmeter.
2) Check resistance between each terminal of couplers discon-
nected.
CAUTION:

Be sure to connect ohmmeter probe from wire harness
side of coupler.

Be sure to turn OFF ignition switch for this check.

Resistance in table below represents that when parts
temperature is 20C (68F).
TERMINALSCIRCUITSTANDARD RESISTANCE
C01-8 to C03-20H02S-1 heater11.7 – 14.3 Ω
C02-19 to C03-20H02S-2 heater11.7 – 14.3 Ω
C02-12 to C02-2 / 15Fuel injector2.4 – 3.6 Ω
C02-7 to C02-2 / 15EVAP canister purge valve30 – 34 Ω
C02-21 to C03-20Fuel pump relay100 – 120 Ω
C02-16 to C02-2 / 15ISC actuator relay100 – 120 Ω
C02-25 to C02-2 / 15EFE heater relay100 – 120 Ω
C02-8 to Body groundShift solenoid-B8 – 20 Ω
C02-9 to Body groundShift solenoid-A8 – 20 Ω
C02-20 to C02-2 / 15Radiator fan control relay100 – 120 Ω
C02-22 to C02-14Main relay100 – 120 Ω
C02-1 to Body groundGroundContinuity
C02-13 to Body groundGroundContinuity
C02-26 to Body groundGroundContinuity

ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10) 6-39
INFORMATION SENSORS
-1. MAP sensor
-2. TP sensor
-3. IAT sensor
-4. ECT sensor
-5. Heated oxygen sensor-1
-6. VSS
-7. Ignition coil
-8. Battery
-9. CMP sensor (in Distributor)
-10. A/C contoller (if equipped)
-11. CKP sensor
-12. CTP switch (in ISC actuator)
-13. Heated oxygen sensor-2OTHERS
A: ECM (PCM)
B: Main relay
C: EVAP canister
D: Injector resistor
E: EFE heater
F: Electric load diode CONTROL DEVICES
a: Fuel injector
b: EVAP canister purge valve
c: Fuel pump relay
d: Malfunction indicator lamp
e: ISC actuator
f: Radiator fan control relay
g: Igniter
h: EFE heater relay
i: ISC actuator relay
COMPONENT LOCATION

6-40 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
“IG COIL METER”Main relay
Ignition switch
In fuseMalfunction indicator lamp in combination meter
TABLE A-1 MALFUNCTION INDICATOR LAMP CIRCUIT CHECK – LAMP DOES
NOT COME “ON” AT IGNITION SWITCH ON (BUT ENGINE AT STOP)
CIRCUIT DESCRIPTION
When the ignition switch is turned ON, ECM (PCM) causes the main relay to turn ON (close the contact point).
Then, ECM (PCM) being supplied with the main power, turns ON the malfunction indicator lamp (MIL). When the
engine starts to run and no malfunction is detected in the system, MIL goes OFF but if a malfunction was or is de-
tected, MIL remains ON even when the engine is running.
INSPECTION
STEPACTIONYESNO
1MIL Power Supply Check
1) Turn ignition switch ON.
Do other indicator / warning lights in
combination meter comes ON?Go to Step 2.“IG COIL METER” fuse blown,
main fuse blown, ignition
switch malfunction, “B/W”
circuit between “IG COIL
METER” fuse and
combination meter or poor
coupler connection at
combination meter.
2ECM (PCM) Power and Ground Circuit
Check
Does engine start?Go to Step 3.Go to TABLE A-3 ECM (PCM)
POWER AND GROUND
CIRCUIT CHECK.
If engine is not cranked, go to
DIAGNOSIS in SECTION 8A.
3MIL Circuit Check
1) Turn ignition switch OFF and disconnect
connectors from ECM (PCM).
2) Check for proper connection to ECM
(PCM) at terminal C02-17.
3) If OK, then using service wire, ground
terminal C02-17 in connector
disconnected.
Does MIL turn on at ignition switch ON?Substitute a known-
good ECM (PCM) and
recheck.Bulb burned out or “V/Y” wire
circuit open.

ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10) 6-41
TABLE A-2 MALFUNCTION INDICATOR LAMP CIRCUIT CHECK – LAMP
REMAINS “ON” AFTER ENGINE STARTS
WIRING DIAGRAM / CIRCUIT DESCRIPTION – Refer to table A-1.
INSPECTION
STEPACTIONYESNO
1Diagnostic Trouble Code (DTC) check
1) Check DTC referring to DTC CHECK section.
Is there any DTC(s)?Go to Step 2 of ENGINE
DIAG. FLOW TABLE.Go to Step 2.
2DTC check
Start engine and recheck DTC while engine
running.
Is there any DTC(s)?Go to Step 3.
3MIL Circuit check
1) Turn OFF ignition switch.
2) Disconnect connectors from ECM (PCM).
Does MIL turn ON at ignition switch ON?“V/Y” wire circuit
shorted to ground.Substitute a known-good
ECM (PCM) and
recheck.

Main fuse Ignition switch
Main fuseMalfunction indicator lamp in combination meter
Relay box“IG COIL METER”
6-42 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
TABLE A-3 ECM (PCM) POWER AND GROUND CIRCUIT CHECK – MIL
DOESN’T LIGHT AT IGNITION SWITCH ON AND ENGINE DOESN’T
START THOUGH IT IS CRANKED UP
CIRCUIT DESCRIPTION
When the ignition switch tuned ON, the main relay turns ON (the contact point closes) and the main power is sup-
plied to ECM (PCM).
INSPECTION
STEPACTIONYESNO
1Main Relay Operating Sound Check
Is operating sound of main relay heard at ignition switch ON?Go to Step 5.Go to Step 2.
2Main Relay Check
1) Turn OFF ignition switch and remove main relay (1).
2) Check for proper connection to main relay (1) at terminal
3 and 4.
3) Check resistance between each two terminals. See Fig. 1
and 2.
Between terminals 1 and 2: Infinity
Between terminals 3 and 4: 100 – 120 Ω
4) Check that there is continuity between terminals 1 and 2
when battery is connected to terminals 3 and 4. See Fig. 3.
Is main relay in good condition?Go to Step 3.Replace main
relay.
3Fuse Check
Is main “FI” fuse in good condition?Go to Step 4.Check for short in
circuits connected
to this fuse.
4ECM (PCM) Power Circuit Check
1) Turn OFF ignition switch, disconnect connectors from ECM
(PCM) and install main relay.
2) Check for proper connection to ECM (PCM) at terminals
C03-20, C02-2, C02-15 and C02-22.
3) If OK, then measure voltage between terminal C03-20 and
ground, C02-22 and ground with ignition switch ON.
Is each voltage 10 – 14 V?Go to Step 5.“B/W”, “W/R” or
“Bl / B” circuit
open.

ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10) 6-45
Fig. 1 for Step 2 Fig. 2 for Step 3
Scan tool
DLC
INSPECTION
STEPACTIONYESNO
1Was “ENGINE DIAG. FLOW TABLE”
performed?Go to Step 2.Go to “ENGINE DIAG.
FLOW TABLE”.
2Check MAP Sensor and Its Circuit.
1) Connect scan tool to DLC with ignition
switch OFF.
2) Turn ignition switch ON.
3) Check intake manifold pressure.
See Fig. 1.
Is it 130 kPa or more or 5 kPa or less?Go to Step 3.Intermittent trouble.
Check for intermittent
referring to
“INTERMITTENT AND
POOR CONNECTION” in
Section 0A.
3Check Wire Harness.
1) Disconnect MAP sensor connector with
ignition switch OFF.
2) Check for proper connection of MAP
sensor at “Lg / R” and “G” wire
terminals.
3) If OK, then with ignition switch ON, check
voltage at each of “Lg” and “Lg / R” wire
terminals. See Fig. 2.
Is voltage about 4 – 6 V at each terminal?Go to Step 4.“Lg” wire open or
shorted to ground circuit or
shorted to power circuit,
“Lg / R” wire open or
shorted to ground, poor
C01-5 connection or
C01-1 connection.
If wire and connection are
OK, confirm that MAP
sensor is normal and then
substitute a known-good
ECM (PCM) and recheck.
NOTE: When battery
voltage is applied to
“Lg” wire, it is possible
that MAP sensor is also
faulty.
4Check MAP sensor according to “MAP
Sensor Individual Check” in Section 6E1.
Is it in good condition?“Lg” wire shorted to
“Lg / R” wire, “G” wire
open, poor C01-9
connection.
If wire and connection are
OK, substitute a known-
good ECM (PCM) and
recheck.Replace MAP sensor.

ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10) 6-47
Fig. 1 for Step 2 Fig. 2 for Step 3 Fig. 3 for Step 4
Scan tool
DLC
INSPECTION
STEPACTIONYESNO
1Was “ENGINE DIAG. FLOW TABLE” performed?Go to Step 2.Go to “ENGINE DIAG.
FLOW TABLE”.
2Check IAT Sensor and Its Circuit.
1) Connect scan tool to DLC with ignition switch
OFF.
2) Turn ignition switch ON.
3) Check intake air temp. displayed on scan tool.
See Fig. 1.
Is –40C (–40F) or 119C (246F) indicated?Go to Step 3.Intermittent trouble.
Check for intermittent
referring to “Intermittent
and Poor Connection”
in Section 0A.
3Check Wire Harness.
1) Disconnect IAT sensor connector with ignition
switch OFF.
2) Check for proper connection to IAT sensor at
“Gr” and “G” wire terminals.
3) If OK, then with ignition switch ON, is voltage
applied to “Gr” wire terminal about 4 – 6 V? See
Fig. 2.Go to Step 5.“Gr” wire open or
shorted to power, or
poor C01-14
connection.
If wire and connection
are OK, substitute a
known-good ECM
(PCM) and recheck.
4Does scan tool indicate –40C (–40F) at Step 2.Go to Step 6.Go to Step 5.
5Check Wire Harness.
1) Check intake air temp. displayed on scan tool
with ignition switch ON.
Is –40C (–40F) indicated?Replace IAT sensor.“Gr” wire shorted to
ground.
If wire is OK, substitute
a known-good ECM
(PCM) and recheck.
6Check Wire Harness.
1) Using service wire, connect IAT sensor
connector terminals.
2) Check intake air temp. displayed on scan tool
with ignition switch ON. See Fig. 3.
Is 119C (246F) indicated?Replace IAT sensor.“Gr” wire open or poor
C01-9 connection.
If wire and connection
are OK, substitute a
known-good ECM
(PCM) and recheck.

ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10) 6-49
Fig. 1 for Step 2 Fig. 2 for Step 3 Fig. 3 for Step 4
Scan tool
DLC
INSPECTION
STEPACTIONYESNO
1Was “ENGINE DIAG. FLOW TABLE” performed?Go to Step 2.Go to “ENGINE DIAG.
FLOW TABLE”.
2Check ECT Sensor and Its Circuit.
1) Connect scan tool with ignition switch OFF.
2) Turn ignition switch ON.
3) Check engine coolant temp. displayed on scan
tool. See Fig. 1.
Is –40C (–40F) or 119C (246F) indicated?Go to Step 3.Intermittent trouble.
Check for intermittent
referring to “Intermittent
and Poor Connection”
in Section 0 A.
3Check Wire Harness.
1) Disconnect ECT sensor connector.
2) Check engine coolant temp. displayed on scan
tool.
Is –40C (–40F) indicated?Replace ECT sensor.“Gr / W” wire shorted to
ground.
If wire is OK, substitute
a known-good ECM
(PCM) and recheck.
4Does scan tool indicate –40C (–40F) at Step 2.Go to Step 6.Go to Step 5.
5Check Wire Harness.
1) Disconnect ECT sensor connector with
ignition switch OFF.
2) Check for proper connection to ECT sensor at
“G” and “Gr / W” wire terminals.
3) If OK, then with ignition switch ON, is voltage
applied to “G” wire terminal about 4 – 6 V?
See Fig. 2.Go to Step 4.“Gr / W” wire open or
shorted to power, or
poor C01-7 connection.
If wire and connection
are OK, substitute a
known-good ECM
(PCM) and recheck.
6Check Wire Harness.
1) Using service wire, connect ECT sensor
connector terminals. See Fig. 3.
2) Turn ignition switch ON and check engine
coolant temp. displayed on scan tool.
Is 119C (246F) indicated?Replace ECT sensor.“G” wire open or
poor C01-9 connection.
If wire and connection
are OK, substitute a
known-good ECM
(PCM) and recheck.