bearing SUZUKI SX4 2006 1.G Service Repair Manual

Downloaded from www.Manualslib.com manuals search engine 3A-13 Drive Shaft / Axle: Front
• When installing left oil seal (1) and right oil seal (2)
using special tool, use care so that oil seals in proper
direction and position as shown in the figure.
Special tool
: 09925–15410
Distance
“a”: 0 – 1 mm (0 – 0.04 in.)
“b”: 8 – 9 mm (0.13 – 0.35 in.)
• Be sure to apply grease to oil seal lip and bearing side
space indicated in the figure.
“A”: Grease 99000–25011 (SUZUKI Super Grease
A) • Press-fit center shaft (1) from left oil seal (2) side.
Specifications
Tightening Torque SpecificationsS6RW0D3117001
NOTE
The specified tightening torque is also described in the following.
“Front Drive Shaft Assembly Components Location”

Reference:
For the tightening torque of fastener not specified in this section, refer to “Fasteners Information in Section 0A”.
2 1
“A”
“b”
“a” “A”
I5RW0A311007-01
12
I5RW0A311008-01
Fastening partTightening torque
Note
N⋅mkgf-mlb-ft
Brake hose mounting bolt 25 2.5 18.0)

Downloaded from www.Manualslib.com manuals search engine Drive Shaft / Axle: Front 3A-14
Special Tools and Equipment
Recommended Service MaterialS6RW0D3118001
NOTE
Required service material is also described in the following.
“Front Drive Shaft Components”

Special ToolS6RW0D3118002
Material SUZUKI recommended product or Specification Note
Grease SUZUKI Super Grease A P/No.: 99000–25011)
09913–84510 09925–15410
Bearing installer Oil seal installer
))
09925–98221 09943–57010
Bearing installer Band compressor
)) / ) / )
09943–57021
Pliers, Low-Profile Clamp
) / )

Downloaded from www.Manualslib.com manuals search engine Drive Shaft / Axle: Rear 3A-18
Specifications
Tightening Torque SpecificationsS6RW0D3127001
NOTE
The specified tightening torque is also described in the following.
“Rear Drive Shaft Components”

Reference:
For the tightening torque of fastener not specified in this section, refer to “Fasteners Information in Section 0A”.
Special Tools and Equipment
Recommended Service MaterialS6RW0D3128001
NOTE
Required service material is also described in the following.
“Rear Drive Shaft Components”

Special ToolS6RW0D3128002
09913–84510 09943–57021
Bearing installer Pliers, Low-Profile Clamp
))

Downloaded from www.Manualslib.com manuals search engine Differential: 3B-14
Rear Differential Symptom DiagnosisS6RW0D3204011
4WD Control Symptom DiagnosisS6RW0D3204012
Diagnose 4WD system after performing the following inspections.
• Perform 4WD control system check referring to “4WD Control System Check”. Condition Possible cause Correction / Reference Item
Gear noiseDeteriorated or water mixed lubricantRepair and replenish referring to “Rear
Differential Oil Change”.
Inadequate or insufficient lubricantRepair and replenish referring to “Rear
Differential Oil Change”.
Maladjusted backlash between drive
bevel pinion and gearAdjust as prescribed referring to “Rear
Differential Disassembly and Reassembly”.
Improper tooth contact in the mesh
between drive bevel pinion and gearAdjust or replace referring to “Rear Differential
Disassembly and Reassembly”.
Loose drive bevel gear securing boltsReplace or retighten referring to “Rear
Differential Disassembly and Reassembly”.
Damaged differential gear(s) or
differential pinion(s)Replace referring to “Rear Differential
Inspection”.
Bearing noise(Constant noise) Deteriorated or water
mixed lubricantRepair and replenish referring to “Rear
Differential Oil Change”.
(Constant noise) Inadequate or
insufficient lubricantRepair and replenish referring to “Rear
Differential Oil Change”.
(Noise while coasting) Damaged
bearing(s) of drive bevel pinionReplace referring to “Rear Differential
Inspection”.
(Noise while turning) Damaged
differential side bearing(s) or axle
bearing(s)Replace referring to “Rear Differential
Inspection”.
Oil leakageClogged breather plugClean.
Worn or damaged oil sealReplace.
Excessive oilAdjust oil level referring to “Rear Differential Oil
Change”.
Loose differential carrier boltsReplace or retighten.
Condition Possible cause Correction / Reference Item
4WD system does not
operate2WD/4WD switch faultyCheck switch referring to “2WD/4WD Switch
Inspection”.
Coupling air temperature sensor faultyCheck coupling air temperature sensor
referring to “Coupling Air Temperature Sensor
Inspection”.
Coupling assembly faultyCheck coupling assembly referring to
“Coupling Assembly Inspection”.
Wiring or grounding faultyRepair as necessary.
4WD control module faultyCheck 4WD control module referring to
“Inspection of 4WD Control Module and Its
Circuits”.
MAF sensor faultyCheck MAF sensor and its circuit.
Accelerator pedal position (APP) sensor
faultyCheck accelerator pedal position (APP) sensor
and its circuit.
CKP sensor faultyCheck CKP sensor and its circuit.
Front and/or rear wheel speed sensor
faultyCheck front and/or rear wheel speed sensor
and its circuit.
Steering angle sensor faultyCheck steering angle sensor and its circuit.
ABS / ESP® control module faultyCheck ABS / ESP
® control module and its
circuit.
ECM faultyCheck ECM and its circuit.
NoiseDamaged or worn bearing(s)Refer to “Rear Differential Inspection”.

Downloaded from www.Manualslib.com manuals search engine 3B-35 Differential:
Rear Differential ComponentsS6RW0D3206013
4 5
9
2
30
6
(a)13
12
(a)
3
A
3A
141617 2118
29
3A
1(b)
22
1217G
101217G
11
8OIL
15OIL
19 20OIL
23OIL
25OIL27OIL
27OIL
25OIL
19OIL18
26 28
OIL
26OIL23OIL
24OIL
(c)
14
7
I5RW0A320026-02
1. Flange nut 13. Differential cover bolt 25. Differential gear
2. Companion flange 14. Spacer 26. Spring washer
3. Oil seal
: Apply grease 99000-25010 to oil seal lip.15. Rear bearing 27. Thrust washer
4. Coupling front bearing 16. Shim 28. Pinion shaft
5. Coupling case
: Apply sealant 99000-31260 to mating surface of carrier and coupling
case.17. Bevel pinion 29. Pinion shaft pin
6. Coupling assembly
: Never disassemble.18. Shim 30. Coupling case bolt
7. Snap ring 19. Differential side bearing : 23 N⋅m (2.3 kgf-m, 17.0 lb-ft)
8. Bevel pinion nut
: Tighten nut so as rotation torque of bevel pinion to be in specified value.20. Bevel gear : 125 N⋅m (12.5 kgf-m, 90.5 lb-ft)
9. Front bearing 21. Differential case : 78 N⋅m (7.8 kgf-m, 56.5 lb-ft)
10. Differential carrier
: Apply sealant 99000-31260 to mating surface of carrier and rear cover.22. Bevel gear bolt : Do not reuse.
11. Coupling air temperature sensor 23. Pinion washer : Apply differential oil.
12. Differential cover 24. Pinion

Downloaded from www.Manualslib.com manuals search engine Differential: 3B-36
Rear Differential Disassembly and ReassemblyS6RW0D3206014
Disassembly
1) Remove rear mounting bracket from rear differential
referring to “Front Mounting Arm and/or Rear
Mounting Bracket Assembly Removal and
Installation”.
2) Remove drive shaft flanges.
3) Separate coupling case from differential carrier using
special tool.
Special tool
: 09912–34510
4) Hold companion flange with special tool and then
remove flange nut.
Special tool
(A): 09930–40113
5) Remove companion flange (1) from pinion. Use
special tool if it is hard to remove.
Special tool
(A): 09913–651356) Remove coupling assembly (1) by using hydraulic
press.CAUTION!
Do not drop coupling assembly. If it is
dropped, replace it with a new one.

7) Disassemble coupling case as follows, if necessary.
a) Remove oil seal using special tool.
Special tool
(A): 09913–50121
b) Remove snap ring using snap ring pliers.
c) Remove bearing using special tool and hydraulic
press.
Special tool
(A): 09913–75830
(A)
I5RW0A320027-01
(A)
1
I5RW0A320028-01
1
I5RW0A320029-01
(A)
I5RW0A320030-01
(A)
I5RW0A320031-01

Downloaded from www.Manualslib.com manuals search engine 3B-37 Differential:
8) Remove oil seals from rear differential (1) using
special tool.
Special tool
(A): 09913–50121
9) Remove differential cover (1) using special tool, and
then take out differential assembly, outer race and
shim all at once.
Special tool
(A): 09912–34510
10) Pull out differential side bearings (1) using special
tools.
Special tool
(A): 09913–60910
(B): 09925–88210
11) Remove drive bevel gear (hypoid gear), differential
gears, differential pinions and pinion shaft as follows.
a) With aluminum plates (2) placed on vise first,
grip differential case with it and remove drive
bevel gear (hypoid gear) (3) by removing its bolts
(1).b) Drive out differential side pinion shaft pin with
special tool and hammer.
Special tool
(B): 09922–85811
c) Disassemble differential gears (2), pinions (3),
washers and shaft (4) in differential case (1).
12) Remove bevel pinion nut with special tool.
Special tool
(A): 09927–27910
13) Remove rear bearing (2) from drive bevel pinion (1)
by using bearing puller (3) and hydraulic press.
1(A)I5RW0A320032-01
(A)
1
I5RW0A320033-01
(A)
(B)
1
I5RW0A320034-02
1
3
2
I5RW0A320035-01
I5RW0A320036-01
(A)
I5RW0A320037-04
I3RH01322026-01

Downloaded from www.Manualslib.com manuals search engine Differential: 3B-38
14) Using a hammer and brass bar (1), drive out front
bearing outer race (2).
15) Using a hammer and brass bar (1), drive out rear
bearing outer race (2).
Reassembly
Judging from faulty conditions noted before disassembly
and what is found through visual check of bearing and
gear tooth etc. after disassembly, prepare replacing
parts and proceed to reassembly according to
procedures as described in the following.
CAUTION!
• Bevel gear and pinion must be replaced as
a set when either replacement becomes
necessary.
• When replacing taper roller bearing,
replace as inner race & outer race
assembly.

1) Press-fit bevel pinion bearing outer races to
differential carrier (1) by using special tools and
hydraulic press as shown in the figure.
Special tool
(A): 09913–85210
(B): 09913–75510
2) After applying differential oil to differential gears (4),
pinions (5), pinion shaft (3), side washers (1), spring
washers (7) and pinion washers (2), install them in
differential case (6).
For correct installing direction of side washers and
spring washers, refer to figure.
NOTE
Used left and right differential side washers
are not interchangeable.

3) Check pinion gear (1) for smooth rotation.
1
2
I5RW0A320038-01
1
2
I5RW0A320039-01
(B)(A)
1
I5RW0A320040-02
7 6
4
5
3
21
I5RW0A320041-01
I3RH01322031-01

Downloaded from www.Manualslib.com manuals search engine 3B-39 Differential:
4) Align holes of pinion shaft and differential case and
drive in differential pinion shaft pin till they are flush
with end surface of case.
Special tool
(A): 09922–85811
5) Put bevel gear (2) on differential case (3) and tighten
new bolts (1) to specified torque.
CAUTION!
Use of any other bolts than that specified is
prohibited.

Tightening torque
Bevel gear bolt (a): 73 N·m (7.3 kgf-m, 52.0 lb-ft)6) Press-fit differential right side bearing (1) with special
tools and hydraulic press.
Special tool
(A): 09913–80113
(B): 09926–48010
7) Hold differential right side bearing (2) with special
tool and press-fit differential left side bearing (1) with
special tools and hydraulic press.
NOTE
Be sure to use bearing holder for the purpose
of protecting lower bearing.

Special tool
(A): 09913–80113
(B): 09926–48010
(C): 09925–88210
I5RW0A320042-01
1, (a)
23
I5RW0A320043-01
I5RW0A320044-01
I5RW0A320045-01

Downloaded from www.Manualslib.com manuals search engine Differential: 3B-40
8) To engage drive bevel pinion and gear correctly, it is pre-required to install drive bevel pinion to differential carrier
properly by using adjusting shim as described on the followings. Shown below is relative positions of drive bevel
pinion, differential carrier and mounting dummy.
Special tool
(A): 09922–76120
(B): 09922–76250
(C): 09922–76140
(D): 09922–76420
(E): 09922–76330
(F): 09922–76150
(G): 09922–76340
(H): 09922–76530
3
2
14
5
6
(H)(B)
(A)
(C)
(D)
(E)
(G)
(F)
“a”“c”“b”
“d”
“e”
I5RW0A320046-03
1. Front bearing “a”: Pinion dummy height + Attachment height 49 mm/1.929 in.
2. Differential carrier “b”: Axle dummy radius 31 mm/1.220 in.
3. Rear bearing “a” + “b”: Mounting dummy size 80 mm/3.149 in.
4. Spacer “c”: Measured dimension
5. Drive bevel pinion “d”: Drive bevel pinion mounting distance 80 mm/3.149 in.
6. Drive bevel gear “e”: Shim size for mounting distance adjustment (“e” = “c”)