bearing SUZUKI SX4 2006 1.G Service Manual PDF

Downloaded from www.Manualslib.com manuals search engine 3B-41 Differential:
9) Set special tools and make drive bevel pinion
mounting dummy.
Special tool
(A): 09922–76120
(B): 09922–76250
10) Install dial gauge (1) to mounting dummy as shown
in figure.
Special tool set distance
“a”: 38.0 mm (1.496 in.)
“b”: 0 mm (0.000 in.)
11) Set special tools and make drive bevel pinion
dummy.
Special tool
(A): 09922–76140
(B): 09922–76420
(C): 09922–76330
(D): 09922–7634012) Apply gear oil to drive bevel pinion bearings, install
special tools with bearings to differential carrier as
shown in figure.
Special tool
(A): 09922–76140
(B): 09922–76420
(C): 09922–76330
(D): 09922–76340
(E): 09922–76150
(F): 09922–76530
NOTE
This installation requires no spacer or oil
seal.

13) Tighten bevel pinion nut (special tool) (1) so that
specified bearing preload is obtained.
NOTE
Before taking measurement, check for
rotation by hand more than 15 revolutions.

Pinion bearing preload (at 50 r/min)
: 1.3 – 2.6 N⋅m (13.0 – 26.0 kgf-cm, 11.3 – 22.6 lb-
in.)
I5RW0A320047-01
(C)
(D)
(A)
(A)(B)I5RW0A320048-01
(E) (D) (C)(B) (A) (F)I5RW0A320049-01
1
I5RW0A320050-01

Downloaded from www.Manualslib.com manuals search engine Differential: 3B-42
14) Set dial gauge to bevel pinion mounting dummy and
make 0 (zero) adjustment on surface plate.
NOTE
• When setting dial gauge to mounting
dummy, tighten screw lightly. Be careful
not to overtighten it, which will cause
damage to dial gauge.
• With dial gauge set, turn dummy back and
forth by hand a couple of times and attain
accurate 0 (zero) adjustment.
• It is desirable that short pointer indicates
beyond 2 mm when long one is at 0 (zero).

15) Place zero-adjusted mounting dummy (1) and dial
gauge set on pinion dummy (2) and take
measurement between zero position and extended
dial gauge measuring tip.
NOTE
• Repeat turning back and forth of dummy
and measure distance as far as top surface
of pinion dummy accurately.
• When dial gauge measuring tip extends
from 0 (zero) position, pointer turns
counterclockwise.

16) Necessary adjusting shim thickness is the same
value as measured value by dial gauge.
17) Select adjusting shim(s) (2) closest to obtained value
from among the following available sizes and put it in
place and then press-fit rear bearing (1) to bevel
pinion (3).
Available shim thickness
0.30, 0.60, 0.63, 0.66, 0.69, 0.72, 0.75, 0.78, 0.81,
0.84 and 0.87 mm (0.012, 0.023, 0.024, 0.026,
0.027, 0.028, 0.030, 0.031, 0.032, 0.033 and 0.034
in.)
Special tool
(D): 09925–18011
18) With new pinion spacer (2) inserted as shown in
figure, install front bearing (1) to differential carrier
(3).
NOTE
Apply differential oil to front and rear
bearings.

I5RW0A320051-01
1
2
I5RW0A320052-01
Necessary shim thickness
“e”= Dial gauge measured
value “c”
I3RH01322055-01
I5RW0A320053-01

Downloaded from www.Manualslib.com manuals search engine 3B-43 Differential:
19) Using special tool and plastic hammer, drive oil seal
(2) into differential carrier (1) as shown in figure.
Then apply grease to oil seal lip.
NOTE
Install oil seal horizontally to surface of
differential carrier.

“A”: Grease 99000–25010 (SUZUKI Super
Grease A)
Distance between differential carrier and oil seal
“a”
: 0.5 – 1.5 mm (0.02 – 0.06 in.)
Special tool
(A): 09913–85210
20) Tighten bevel pinion nut (1) gradually with special
tool to specified torque while turning bevel pinion.
Set bearing preload of bevel pinion to specification.
NOTE
• Before taking measurement with torque
wrench, check for smooth rotation with
turning bevel pinion 15 revolutions or
more by hand.
• Be sure to tighten gradually and carefully
till specified pinion bearing preload is
obtained. Turning back overtightened
flange nuts should be avoided.
• Measure pinion bearing preload while
turning bevel pinion about 50 rpm.
• Write down measured value of bevel pinion
bearing preload for differential side
bearing shim adjustment.

Special tool
(A): 09927–27910
Tightening torque
Bevel pinion nut: 230 – 340 N·m (23.0 – 34.0 kgf-
m, 166.5 – 246.0 lb-ft)
Bevel pinion bearing preload (Bevel pinion
rotational torque)
: 1.3 – 2.6 N⋅m (13.0 – 26.0 kgf-cm, 11.3 – 22.6 lb-
in.)
21) Install differential case assembly, bearing outer
races, removed shim and differential cover,
temporarily.
NOTE
• Used left and right outer races are not
interchangeable.
• When measuring bevel pinion bearing
preload, install differential cover with
sealant not applied.

22) Select differential side bearing shim so that bevel
pinion bearing preload may be specified value.
NOTE
Select shims so that thickness of right side
shims and left side shims become almost
even.

Bevel pinion bearing preload
Preload measured in Step 20) + 0.3 – 0.7 N⋅m (3 –
7 kgf-cm, 2.6 – 6.0 lb-in.)
Available shim thickness
0.45, 2.30, 2.35, 2.40, 2.45, 2.50, 2.55, 2.60, 2.65
and 2.70 mm (0.017, 0.090, 0.092, 0.094, 0.096,
0.098, 0.100, 0.102, 0.104 and 0.106 in.)
(A)
11
2, “A”
“a”
I5RW0A320054-02
(A)
1
I5RW0A320055-03
I5RW0A320056-01

Downloaded from www.Manualslib.com manuals search engine Differential: 3B-46
26) Clean mating surface of differential carrier (1) and
differential cover, apply sealant to carrier as shown
in figure by such amount that its section is 1.5 mm
(0.059 in.) in diameter, mate differential cover with
differential carrier, and then tighten bolts to specified
torque.
“A”: Sealant 99000–31260 (SUZUKI Bond
No.1217G)
Tightening torque
Differential cover bolt: 23 N·m (2.3 kgf-m, 17.0
lb-ft)
27) Assemble coupling case as follows.
a) Install bearing using special tool and hydraulic
press.
Special tool
(A): 09913–75830
b) Install snap ring using snap ring pliers.
c) Apply grease to oil seal lip, install oil seal (2) to
coupling case (1) using special tool as shown in
figure.
NOTE
Install oil seal horizontally to surface of
coupling case.

“A”: Grease 99000–25010 (SUZUKI Super
Grease A)
Distance between case and oil seal “a”
: 1.5 – 2.5 mm (0.06 – 0.10 in.)
Special tool
(A): 09913–7581028) Install spacer (1) to coupling assembly (2) as shown
in figure.
29) Install grommet of coupling harness into groove of
coupling case and then install coupling assembly by
using hydraulic press.
30) Install companion flange to pinion, and then hold
companion flange with special tool and tighten flange
nut.
Tightening torque
Flange nut: 110 N·m (11.0 kgf-m, 79.5 lb-ft)
Special tool
(A): 09930–40113
“A”
1
I5RW0A320058-02
(A)
I5RW0A320059-02
(A)
1 12, “A”“a”
I5RW0A320060-02
12
12
I5RW0A320065-01
(A)
I5RW0A320061-01

Downloaded from www.Manualslib.com manuals search engine 3B-47 Differential:
31) Clean mating surface of differential carrier (1) and
coupling case (2), apply sealant to carrier as shown
in figure by such amount that its section is 1.5 mm
(0.059 in.) in diameter, mate coupling case with
differential carrier as shown in figure, and then
tighten bolts to specified torque.
“A”: Sealant 99000–31260 (SUZUKI Bond
No.1217G)
Tightening torque
Coupling case bolt (a): 23 N·m (2.3 kgf-m, 17.0
lb-ft)
NOTE
Install coupling pin (3) by fitting it to groove
(4) of coupling case.

32) Apply grease to oil seal lip, and then install oil seals
(1) to rear differential (2) using special tool as shown
in figure.
NOTE
Install oil seal horizontally to surface of rear
differential case.

“A”: Grease 99000–25010 (SUZUKI Super
Grease A)
Distance between rear differential and oil seal
“a”
: 1.0 – 2.0 mm (0.04 – 0.08 in.)
Special tool
(A): 09913–75810
33) Install drive shaft flange.
34) Install rear mounting bracket to rear differential
referring to “Front Mounting Arm and/or Rear
Mounting Bracket Assembly Removal and
Installation”.
Rear Differential InspectionS6RW0D3206015
• Check companion flange for wear or damage.
• Check bearings for wear or discoloration.
• Check differential carrier for cracks.
• Check drive bevel pinion and bevel gear for wear or
cracks.
• Check side gears, pinion gears and pinion shaft for
wear or damage.
• Check side gear spline for wear or damage.
1 4
3 2“A”
(a)
I5RW0A320062-04
(A)
2 21, “A”
“a”
I5RW0A320063-02

Downloaded from www.Manualslib.com manuals search engine 3B-49 Differential:
Special ToolS6RW0D3208002
09900–20607 09900–20701
Dial gauge Magnetic stand
))
09912–34510 09913–50121
Case separator Oil seal remover
) / )) / )
09913–60910 09913–65135
Bearing and gear puller (40-
60mm)Bearing puller
))
09913–70123 09913–75510
Bearing installing tool Bearing installer
))
09913–75810 09913–75830
Bearing installer Steering pinion bush
installer
) / )) / )
09913–80113 09913–85210
Bearing installer Bearing installer
) / )) / ) / )
09922–76120 09922–76140
Mounting dummy shaft Bevel pinion shaft
) / )) / ) / )

Downloaded from www.Manualslib.com manuals search engine Differential: 3B-50
09922–76150 09922–76250
Bevel pinion nut Bevel gear dummy
) / )) / )
09922–76330 09922–76340
Bevel pinion rear collar Bevel pinion rear collar
) / ) / )) / ) / )
09922–76420 09922–76530
Bevel pinion front collar Bevel pinion gauge block
) / ) / )) / )
09922–85811 09925–18011
Spring pin remover (4.5 mm) Transmission gear, bush
and bearing installer
) / ))
09925–88210 09926–48010
Bearing puller attachment Universal joint assembling
tool
) / )) / )
09927–27910 09930–40113
Holder, bevel pinion Flywheel rotor holder
) / )) / )
09951–26020 SUZUKI scan tool
Bush remover & installer
support—
) / )This kit includes following
items. 1. Tech 2, 2. PCMCIA
card, 3. DLC cable, 4. SAE
16/19 adapter, 5. Cigarette
cable, 6. DLC loop back
adapter, 7. Battery power
cable, 8. RS232 cable, 9.
RS232 adapter, 10. RS232
loop back connector, 11.
Storage case, 12. ) / )

Downloaded from www.Manualslib.com manuals search engine 3C-1 Transfer:
Driveline / Axle
Transfer
General Description
Transfer DescriptionS6RW0D3301001
The transfer is mounted on transaxle case by fastening bolt with reduction drive gear in transfer and differential case in
transaxle coupled by involute spline. Driving force from transaxle is transmitted to propeller shaft through reduction
drive gear, reduction driven gear and bevel gear of transfer. As bevel gears, which change the direction of driving
torque axis to the direction of the angle with 90 degrees, hypoid gears are provided. Hypoid gears have an advantage
of preventing gear noise, at the same time, they require accurate adjustment of tooth contact and backlash.
Diagnostic Information and Procedures
Transfer Symptom DiagnosisS6RW0D3304001
2
1
8
34
5
6
7
9
10I5RW0A330001-01
1. Intermediate shaft 5. Reduction driven gear 9. Transfer output retainer
2. Left case 6. Bevel gear 10. Transfer output flange
3. Reduction drive gear 7. Bevel pinion
4. Right case 8. Spacer
Condition Possible cause Correction / Reference Item
NoiseInadequate or insufficient lubricantReplenish.
Damaged or worn bearing(s)Replace.
Damaged or worn gear(s)Replace.
Preload of taper roller bearing is
reducedAdjust.

Downloaded from www.Manualslib.com manuals search engine Transfer: 3C-4
• Pour transaxle oil and transfer oil referring to “Manual
Transaxle Oil Change in Section 5B” and “Transfer Oil
Change”.
Transfer Assembly ComponentsS6RW0D3306004
1
2
6
9
1110
8
7
3A
4
5
36
OIL
(a) 5
(a)
OIL
28
18
30
27
25
21
28
13
12
22OIL
OIL
32A
31A
1322(d)
34A
33
23A
2019
(c)1217G
291217G
(b)
35
15A
26
26 14
24
17
161217G(b)
A
I5RW0A330007-05
1. Transfer output flange nut
: After tightening nut so as rotational torque
of bevel pinion to be in specified value,
caulk nut securely.15. Dowel pin 29. Transfer right case
: Apply sealant 99000-31260 to
mating surface with right case.
2. Transfer output flange 16. Oil drain plug
: Apply sealant 99000-31260 to thread
part.30. Oil level / filler plug
: Apply sealant 99000-31260 to
thread part.
3. Oil seal
: Apply grease 99000-25010 to oil seal lip.17. Transfer left case
: Apply grease 99000-25010 to left case.31. Left case oil seal No.1
: Apply grease 99000-25010 to oil
seal lip.
4. Pinion shaft rear taper roller bearing 18. Transfer case bolt 32. Left case oil seal No.2
: Apply grease 99000-25010 to oil
seal lip.
5. Transfer output retainer bolt 19. Reduction drive gear left bearing 33. Right case oil seal No.3
: Apply grease 99000-25010 to oil
seal lip.
6. O-ring
: Apply grease 99000-25010 to all around
surface.20. Reduction drive gear 34. Right case oil seal No.2
: Apply grease 99000-25010 to oil
seal lip.
7. Shim 21. Reduction driven gear left taper roller
bearing35. Right case oil seal No.1
: Apply grease 99000-25010 to oil
seal lip.
8. Spacer 22. Reduction driven gear right taper roller
bearing36. Transfer output retainer

Downloaded from www.Manualslib.com manuals search engine 3C-5 Transfer:
Transfer Assembly Disassembly and
Reassembly
S6RW0D3306005
Disassembly
NOTE
It is possible to disassemble transfer
assembly without removing intermediate
shaft with Step 1) to 4) performed if not
necessary.

1) Remove right case oil seal No.1 (1) from transfer
right case using special tool.
Special tool
: 09913–50121
2) Remove snap ring (2) by using snap ring pliers.
3) Remove intermediate shaft (4) with intermediate
shaft bearing (3) from transfer assembly.
4) Remove intermediate shaft bearing (3) from
intermediate shaft (4) by using bearing puller and
hydraulic press.
5) Remove transfer output retainer assembly (1) and
shim (3) by removing retainer bolts (2).
6) Remove transfer case bolts (4).
7) Separate transfer right case (5) from transfer left
case (6) by using special tool.
Special tool
(A): 09912–34510
8) Remove reduction drive gear assembly (7) and
reduction driven gear assembly (9).
9) Remove shim (10) and bearing outer races (8).
NOTE
When it is difficult to remove bearing outer
races from cases, remove them with special
tool.

Special tool
(B): 09944–96011Reassembly
1) Select appropriate shim as follows.
a) Measure distance “a” between taper roller
bearing outer races of reduction driven gear
assembly (1).
b) Measure depth “b” of left case (2) and “c” of right
case (3).
c) Obtain adjusting shim thickness by the following
equation.
9. Pump seal 23. Reduction drive gear right bearing : 55 N⋅m (5.5 kgf-m, 40.0 lb-ft)
10. Pinion shaft front taper roller bearing 24. Intermediate shaft : 21 N⋅m (2.1 kgf-m, 15.5 lb-ft)
11. Bevel pinion 25. Oil protect plate bolt
: Apply thread lock cement 99000-32110
to thread part.: 23 N⋅m (2.3 kgf-m, 17.0 lb-ft)
12. Bevel gear 26. Snap ring : 9 N⋅m (0.9 kgf-m, 6.5 lb-ft)
13. Reduction driven gear 27. Oil protect plate : Do not reuse.
14. Intermediate shaft bearing 28. Shim : Apply transfer oil.
4
3
2
1
I5RW0A330008-01
11. Dowel pin
Necessary
shim
thickness=Depth
“b”+Depth
“c”–Distanc
e “a”+0.1 mm
(0.004
in.)
7
(B)
5
11
310 9 10
8 64
8
(A)
12
2
I5RW0A330009-03
23
1
“b”
“a”“c”
I5RW0A330010-01