SUZUKI SX4 2006 1.G Service Manual Online

Downloaded from www.Manualslib.com manuals search engine Engine General Information and Diagnosis: 1A-31
8Communication check between scan tool and ECM
1) Turn ignition switch to OFF position.
2) Connect ECM, BCM, ABS control module and
combination meter connectors.
3) Check communication between scan tool and ECM by
DTC check in ECM.
Is it possible to check DTC in ECM?A/T model: Go to Step
9.
M/T model: Substitute a
known-good ECM and
recheck.Go to Step 4 through
Step 11 of
“Troubleshooting for
CAN-DTC”.
9Communication check between scan tool and TCM
1) Turn ignition switch to OFF position.
2) Connect TCM connectors.
3) Check communication between scan tool and TCM by
DTC check in TCM.
Is it possible to check DTC in TCM?Identify malfunction
control module by
performing Step 13
through Step 14 of
“Troubleshooting for
CAN-DTC”.Go to Step 10.
10Internal circuit check in ECM
1) Turn ignition switch to OFF position and then disconnect
negative (–) cable at battery.
2) Disconnect TCM connectors.
3) Measure resistance between the followings
• Between CAN High terminal on DLC and “C06-17”
terminal on TCM connector
• Between CAN Low terminal on DLC and “C06-7”
terminal on TCM connector
Is each resistance 0 – 1
Ω?Substitute a known-
good TCM and recheck.Substitute a known-
good ECM and recheck. Step Action Yes No

Downloaded from www.Manualslib.com manuals search engine 1A-32 Engine General Information and Diagnosis:
DTC TableS6RW0D1104005
NOTE
• There are two types of OBD system depending on the vehicle specification.
For identification, refer to “Precaution on On-Board Diagnostic (OBD) System”.
• For non-Euro-OBD model, some of DTC No. with delta (U) mark in the following table can not be
detected by ECM depending on vehicle specification.
• With the CAN communication generic scan tool, only star (*) marked DTC No. in the following table
can be read.
• 1 driving cycle: MIL lights up when DTC is detected during 1 driving cycle.
• 2 driving cycles: MIL lights up when the same DTC is detected also in the next driving cycle after
DTC is detected and stored temporarily in the first driving cycle.
• *2 driving cycles:
MIL blinks or lights up. Refer to “DTC P0300 / P0301 / P0302 / P0303 / P0304: Random Misfire
Detected / Cylinder 1 / Cylinder 2 / Cylinder 3 / Cylinder 4 Misfire Detected” for details.

DTC No. Detecting itemDetecting condition
(DTC will set when detecting:)MIL
) *P0010Camshaft position actuator circuit
(for engine with VVT system)Oil control valve circuit open or short.1 driving
cycle
) *P0011Camshaft position – timing over-
advanced or system performance
(for engine with VVT system)Actual value of advanced valve timing does not reach
target value, or valve timing is advanced although ECM
command is most retarding.2 driving
cycles
) *P0012Camshaft position – timing over-
retarded
(for engine with VVT system)2 driving
cycles
) *P0031HO2S heater control circuit low
(Sensor-1)Heater current is less than specification while heater ON.2 driving
cycles
) *P0032HO2S heater control circuit high
(Sensor-1)Heater current is more than specification while heater ON.2 driving
cycles
)
U*P0037HO2S heater control circuit low
(Sensor-2)Heater current is less than specification while heater ON.2 driving
cycles
)
U*P0038HO2S heater control circuit high
(Sensor-2)Heater current is more than specification while heater ON.2 driving
cycles
)
U*P0101Mass air flow circuit range/
performanceMAF sensor volume is more than specification or less
than specification.2 driving
cycles
) *P0102 Mass air flow circuit low input Output voltage of MAF sensor is less than specification.1 driving
cycle
) *P0103 Mass air flow circuit high input Output voltage of MAF sensor is more than specification.1 driving
cycle
)
U*P0106Manifold absolute pressure circuit
range/performanceDifference between Max. manifold absolute pressure
value and Min. manifold pressure value is less than
specification or difference between barometric pressure
value and manifold pressure value is less than
specification2 driving
cycles
)
U*P0107Manifold absolute pressure circuit
low inputOutput voltage of MAP sensor is less than specification.
1 driving
cycle
)
U*P0108Manifold absolute pressure circuit
high inputOutput voltage of MAP sensor is more than specification.1 driving
cycle
)
U* P 0 111Intake air temperature sensor circuit
range/performanceVariation of intake air temperature from engine start is
less than specification.2 driving
cycles
) *P0112Intake air temperature sensor circuit
lowCircuit voltage of IAT sensor is less than specification.1 driving
cycle
) *P0113Intake air temperature sensor circuit
highCircuit voltage of IAT sensor is more than specification.1 driving
cycle
)
U*P0116Engine coolant temperature circuit
range/performanceEngine coolant temperature is less than specified
temperature for specified time from engine start.2 driving
cycles

Downloaded from www.Manualslib.com manuals search engine Engine General Information and Diagnosis: 1A-33
) *P0117Engine coolant temperature circuit
lowCircuit voltage of ECT sensor is less than specification.1 driving
cycle
) *P0118Engine coolant temperature circuit
highCircuit voltage of ECT sensor is more than specification.1 driving
cycle
) *P0122Throttle position sensor (main)
circuit lowOutput voltage of throttle position sensor (main) is lower
than specification.1 driving
cycle
) *P0123Throttle position sensor (main)
circuit highOutput voltage of throttle position sensor (main) is higher
than specification.1 driving
cycle
)
U*P0131O2 sensor (HO2S) circuit low
voltage (Sensor-1)Max. output voltage of HO2S-1 is less than specification.2 driving
cycles
)
U*P0132O2 sensor (HO2S) circuit high
voltage (Sensor-1)Min. output voltage of HO2S-1 is more than specification.2 driving
cycles
)
U*P0133O2 sensor (HO2S) circuit slow
response (Sensor-1)Response time of HO2S-1 output voltage between rich
and lean is longer than specification.2 driving
cycles
) *P0134O2 sensor (HO2S) circuit no activity
detected (Sensor-1)Output voltage of HO2S-1 is more than specification or
less than specification. (or HO2S-1 circuit open or short)2 driving
cycles
)
U*P0137O2 sensor (HO2S) circuit low
voltage (Sensor-2)Output voltage of HO2S-2 is less than specification while
engine is idling after driving with high engine load and
Max. output voltage of HO2S-2 minus Min. output voltage
of HO2S-2 is less than specification.2 driving
cycles
)
U*P0138O2 sensor (HO2S) circuit high
voltage (Sensor-2)Output voltage of HO2S-2 is more than specification while
engine is idling after driving with high engine load and
Max. output voltage of HO2S-2 minus Min. output voltage
of HO2S-2 is less than specification.2 driving
cycles
)
U*P0140O2 sensor (HO2S) circuit no activity
detected (Sensor-2)Output voltage of HO2S-2 is more than specification after
warming up engine.
2 driving
cycles
)
U*P0171System too leanTotal fuel trim is larger than specification for specified time
or longer. (Fuel trim toward rich side is large.)2 driving
cycles
)
U*P0172System too richTotal fuel trim is smaller than specification for specified
time or longer. (Fuel trim toward lean side is large.)2 driving
cycles
) *P0222Throttle position sensor (sub) circuit
lowOutput voltage of throttle position sensor (sub) is lower
than specification.1 driving
cycle
) *P0223Throttle position sensor (sub) circuit
highOutput voltage of throttle position sensor (sub) is higher
than specification.1 driving
cycle
)
U*P0300Random misfire detected
Misfire of such level as to cause damage to three way
catalyst or misfire of such level as to deteriorate emission.*2 driving
cycles )U*P030
1 /
U*P0302 /
U*P0303 /
U*P0304Cylinder 1 misfire detected
Cylinder 2 misfire detected
Cylinder 3 misfire detected
Cylinder 4 misfire detected
) *P0327 Knock sensor circuit low Output voltage of knock sensor is less than specification.1 driving
cycle
) *P0328 Knock sensor circuit high Output voltage of knock sensor is more than specification.1 driving
cycle
) *P0335 Crankshaft position sensor circuitNo signal of CKP sensor for specified time even if starting
motor signal is input.1 driving
cycle
) *P0340 Camshaft position sensor circuit CMP sensor pulse is out of specification.1 driving
cycle
)
U*P0401Exhaust gas recirculation flow
detected as insufficientDifference in intake manifold absolute pressure between
opened EGR valve and closed EGR valve is less than
specification.2 driving
cycles
)
U*P0402Exhaust gas recirculation flow
detected as excessive
Difference in intake manifold absolute pressure between
opened EGR valve and closed EGR valve is more than
specification.2 driving
cycles
)
U*P0403Exhaust gas recirculation control
circuitOutput voltage is different from output command with
more than one pole out of 4 poles.1 driving
cycle DTC No. Detecting itemDetecting condition
(DTC will set when detecting:)MIL

Downloaded from www.Manualslib.com manuals search engine 1A-34 Engine General Information and Diagnosis:
)
U*P0420Catalyst system efficiency below
thresholdOutput waveforms of HO2S-1 and HO2S-2 are similar.2 driving
cycles
)
U*P0443Evaporative emission system purge
control valve circuitMonitor signal of EVAP canister purge valve is different
from command signal. (circuit open or shorted to ground)2 driving
cycles
) P0462 Fuel level sensor circuit lowCircuit voltage of fuel level sensor is less than
specification.—
) P0463 Fuel level sensor circuit highCircuit voltage of fuel level sensor is more than
specification.—
)
U*P0480Fan 1 control circuitMonitor signal of radiator cooling fan relay is different from
command signal.1 driving
cycle
)
UP0481Fan 2 control circuitMonitor signal of A/C condenser cooling fan relay is
different from command signal.—
) *P0500 Vehicle speed sensor No VSS signal during fuel cut for specified time or longer.2 driving
cycles
) P0532A/C refrigerant pressure sensor
circuit lowOutput voltage of A/C refrigerant pressure sensor is less
than specification.—
) P0533A/C refrigerant pressure sensor
circuit highOutput voltage of A/C refrigerant pressure sensor is more
than specification.—
) *P0601Internal control module memory
check sum errorData write error or check sum error.1 driving
cycle
) P0602 Control module programming error Data programming error.1 driving
cycle
) *P0607 Control module performance Data programming error.1 driving
cycle
)
U*P0616Starter relay circuit lowStarter signal is low voltage even though engine is started
with vehicle at stop.2 driving
cycles
)
U*P0617Starter relay circuit highStarter signal is high voltage for specified time while
engine is running.2 driving
cycles
) *P1510
ECM backup power supply
malfunctionBackup power voltage is out of specification after starting
engine.1 driving
cycle
) *P2101Throttle actuator control motor
circuit range/performanceMonitor signal of throttle actuator output (duty output) is
inconsistent with throttle actuator control command.1 driving
cycle
) *P2102Throttle actuator control motor
circuit lowPower supply voltage of throttle actuator control circuit is
lower than specification even if throttle actuator control
relay turned on.1 driving
cycle
) *P2103Throttle actuator control motor
circuit highPower supply voltage of throttle actuator control circuit is
higher than specification even if throttle actuator control
relay turned off.1 driving
cycle
) *P2111Throttle actuator control system –
stuck openThrottle valve default opening is greater than 8° from
complementary closed position when diagnosing throttle
valve at ignition switch turned OFF.1 driving
cycle
) *P2119Throttle actuator control throttle
body range/performanceDifference between actual throttle valve opening angle
and opening angle calculated by ECM is more than
specification.1 driving
cycle
) *P2122Pedal position sensor (main) circuit
low inputOutput voltage of pedal position sensor (main) is lower
than specification.1 driving
cycle
) *P2123Pedal position sensor (main) circuit
high inputOutput voltage of pedal position sensor (main) is higher
than specification.1 driving
cycle
) *P2127Pedal position sensor (sub) circuit
low inputOutput voltage of pedal position sensor (sub) is lower
than specification.1 driving
cycle
) *P2128Pedal position sensor (sub) circuit
high inputOutput voltage of pedal position sensor (sub) is higher
than specification.1 driving
cycle
) *P2135Throttle position sensor (main / sub)
voltage correlationDifference between the opening angle based on throttle
position sensor (main) and the opening angle based on
throttle position sensor (sub) is more than specification.1 driving
cycle DTC No. Detecting itemDetecting condition
(DTC will set when detecting:)MIL

Downloaded from www.Manualslib.com manuals search engine Engine General Information and Diagnosis: 1A-35
) *P2138Pedal position sensor (main / sub)
voltage correlationDifference between the opening angle based on
accelerator pedal position sensor (main) and the opening
angle based on accelerator pedal position sensor (sub) is
more than specification.1 driving
cycle
)
U*P2227Barometric pressure circuit range/
performanceDifference of barometric pressure value and intake
manifold pressure value is more than specification at
engine start.2 driving
cycles
) *P2228 Barometric pressure circuit lowBarometric pressure sensor voltage is less than
specification.1 driving
cycle
) *P2229 Barometric pressure circuit highBarometric pressure sensor voltage is more than
specification.1 driving
cycle
) U0073Control Module Communication Bus
OffTransmission error that is inconsistent between
transmission data and transmission monitor (CAN bus
monitor) data is detected more than 30 times
continuously.—
) *U0101Lost Communication With
Transmission Control ModuleReception error of communication data for TCM is
detected for longer than specified time continuously.1 driving
cycle
) *U0121Lost Communication Anti-Lock
Brake System (ABS) Control
ModuleReception error of communication data for ESP® control
module or ABS hydraulic unit / control module assembly
is detected for longer than specified time continuously.1 driving
cycle
)U0140Lost Communication With Body
Control ModuleReception error of communication data for BCM is
detected for longer than specified time continuously.—
P1614 Transponder response error
Refer to “DTC Table in Section 10C”.—
P1615ID code does not registered
(vehicle equipped with keyless start
system only)—
P1616Different registration ID codes
(vehicle equipped with keyless start
system only)—
P1618CAN communication error
(reception error for keyless start
control module) (vehicle equipped
with keyless start system only)—
P1621Immobilizer communication line
error—
P1622 EEPROM error—
P1623 Unregistered transponder—
P1625 Immobilizer antenna error—
P1636Immobilizer information registration
failure—
P1638 Immobilizer information mismatched — DTC No. Detecting item
Detecting condition
(DTC will set when detecting:)MIL

Downloaded from www.Manualslib.com manuals search engine 1A-36 Engine General Information and Diagnosis:
For Vehicle Equipped with A/TS6RW0D1104081
NOTE
There are two types of OBD system depending on the vehicle specification.
For identification, refer to “Precaution on On-Board Diagnostic (OBD) System”.

When using CAN communication OBD generic scan tool, not only the previous star (*) marked ECM DTC(s) but also
the following DTC(s) is displayed on CAN communication OBD generic scan tool simultaneously.
Fail-Safe TableS6RW0D1104006
When any of the following DTCs is detected, ECM enters fail-safe mode as long as malfunction continues to exist but
that mode is cancelled when ECM detects normal condition after that. DTC No. Detecting itemDetecting condition
(DTC will set when detecting)
P0705 Transmission range sensor circuit malfunction (PRNDL input)
Refer to “DTC Table in Section 5A”. P0707 Transmission range sensor circuit low
P0711Transmission fluid temperature sensor “A” circuit range/
performance
P0712 Transmission fluid temperature sensor circuit low
P0713 Transmission fluid temperature sensor circuit high
P0717 Input/Turbine speed sensor circuit no signal
P0722 Output speed sensor (VSS) circuit no signal
P0741 Torque converter clutch circuit performance or stuck off
P0742 Torque converter clutch circuit stuck on
P0751 Shift solenoid-A (No.1) performance or stuck off
P0752 Shift solenoid-A (No.1) stuck on
P0756 Shift solenoid-B (No.2) performance or stuck off
P0757 Shift solenoid-B (No.2) stuck on
P0787 Shift/Timing solenoid control circuit low
P0788 Shift/Timing solenoid control circuit high
P0961 Pressure control solenoid “A” control circuit range/performance
P0962 Pressure control solenoid control circuit low
P0963 Pressure control solenoid control circuit high
P0973 Shift solenoid-A (No.1) control circuit low
P0974 Shift solenoid-A (No.1) control circuit high
P0976 Shift solenoid-B (No.2) control circuit low
P0977 Shift solenoid-B (No.2) control circuit high
P1702 Internal control module memory check sum error
P1723 Range select switch malfunction
P1878 Torque converter clutch shudder
P2762Torque converter clutch (TCC) pressure control solenoid control
circuit range/performance
P2763Torque converter clutch pressure control solenoid control circuit
high
P2764Torque converter clutch pressure control solenoid control circuit
low
U0100 Lost communication with ECM/PCM “A”
DTC No. Detected item Fail-safe operation
) P0102 Mass air flow circuit low input • ECM controls injector drive time (fuel injection
volume) according to throttle valve opening
(closed throttle position or not).
• ECM stops EGR control. ) P0103 Mass air flow circuit high input
) P0112 Intake air temperature sensor circuit low ECM controls actuators assuming that intake air
temperature is 20 °C (68 °F). ) P0113 Intake air temperature sensor circuit high
) P0117 Engine coolant temperature circuit low • ECM controls actuators assuming that engine
coolant temperature is 80 °C (176 °F).
• ECM operates radiator cooling fan. ) P0118 Engine coolant temperature circuit high

Downloaded from www.Manualslib.com manuals search engine Engine General Information and Diagnosis: 1A-37
) P0122 Throttle position sensor (main) circuit low• ECM turns off throttle actuator control relay and
throttle valve is fixed at the opening of about 7°
from its completely closed position (default
opening).
• ECM controls fuel cut at specified engine speed.
• ECM stops air/fuel ratio control.
) P0123 Throttle position sensor (main) circuit high• ECM turns off throttle actuator control relay and
throttle valve is fixed at the opening of about 7°
from its completely closed position (default
opening).
• ECM controls fuel cut at specified engine speed.
• ECM stops air/fuel ratio control. ) P0222 Throttle position sensor (sub) circuit low
) P0223 Throttle position sensor (sub) circuit high
) P0335 Crankshaft position sensor circuit • Ignition timing is fixed.
) P0340 Camshaft position sensor circuitECM changes injection control system from
sequential injection to simultaneous one.
) P0500 Vehicle speed sensor• ECM controls actuators assuming that vehicle
speed is 0 km/h (0 mile/h).
• ECM stops IAC feedback control.
) P2101Throttle actuator control motor circuit range
/ performance)• ECM turns off throttle actuator control relay and
throttle valve is fixed at the opening of about 7°
from its completely closed position (default
opening).
• ECM controls fuel cut at specified engine speed. ) P2102 Throttle actuator control motor circuit low
) P2103 Throttle actuator control motor circuit highECM controls fuel cut at specified engine speed.
) P 2 111Throttle actuator control system – stuck
open)• ECM turns off throttle actuator control relay and
throttle valve is fixed at the opening of about 7°
from its completely closed position (default
opening).
• ECM controls fuel cut at specified engine speed.
) P2119Throttle actuator control throttle body range
/ performance)• ECM turns off throttle actuator control relay and
throttle valve is fixed at the opening of about 7°
from its completely closed position (default
opening).
• ECM controls fuel cut at specified engine speed.
) P2122Pedal position sensor (main) circuit low
input)
• ECM turns off throttle actuator control relay and
throttle valve is fixed at the opening of about 7°
from its completely closed position (default
opening).
• ECM controls fuel cut at specified engine speed. ) P2123Pedal position sensor (main) circuit high
input)
) P2127 Pedal position sensor (sub) circuit low input)
) P2128Pedal position sensor (sub) circuit high
input)
) P2135Throttle position sensor (main) / (sub)
voltage correlation)
) P2138Pedal position sensor (main) / (sub) voltage
correlation)
) P2228 Barometric pressure circuit low ECM controls actuators assuming that barometric
pressure is 101.33 kPa (762 mmHg). ) P2229 Barometric pressure circuit high DTC No. Detected item Fail-safe operation

Downloaded from www.Manualslib.com manuals search engine 1A-38 Engine General Information and Diagnosis:
Scan Tool DataS6RW0D1104007
As the data values are standard values estimated on the basis of values obtained from the normally operating vehicles
by using a scan tool, use them as reference values. Even when the vehicle is in good condition, there may be cases
where the checked value does not fall within each specified data range. Therefore, judgment as abnormal should not
be made by checking with these data alone.
Also, conditions that can be checked by the scan tool are those detected by ECM and output from ECM as commands
and there may be cases where the engine or actuator is not operating (in the condition) as indicated by the scan tool.
Be sure to use the timing light to check the ignition timing.
NOTE
• There are two types of OBD system depending on the vehicle specification.
For identification, refer to “Precaution on On-Board Diagnostic (OBD) System”.
• With the CAN communication generic scan tool, only star (*) marked data in the following table can
be read.
• When checking the data with the engine running at idle or racing, be sure to shift M/T gear to the
neutral position and A/T gear to the “Park” position and pull the parking brake fully. Also, if nothing
or “no load” is indicated, turn OFF A/C (if equipped with A/C), all electric loads, P/S and all the other
necessary switches.

Scan tool data Vehicle conditionNormal condition /
reference values
*) COOLANT TEMP
(ENGINE COOLANT TEMP.)At specified idle speed after warming up 80 – 100 °C, 176 – 212 °F
*) INTAKE AIR TEMP. At specified idle speed after warming up–5 °C (23 °F) + environmental
temp. to 40 °C (104 °F) +
environmental temp.
*) ENGINE SPEED It idling with no load after warming up Desired idle speed ± 50 rpm
) DESIRED IDLE
(DESIRED IDLE SPEED)It idling with radiator cooling fan stopped and all
electrical parts turned OFF after warming up, M/T at
neutral700 rpm
*) MAF
(MASS AIR FLOW RATE)At specified idle speed with no load after warming up1.0 – 4.0 g/s 0.14 – 0.52 lb/
min.
At 2500 r/min. with no load after warming up4.0 – 9.0 g/s 0.53 – 1.58 lb/
min.
*) CALC LOAD
(CALCULATED LOAD
VA L U E )At specified idle speed with no load after warming up 16 – 36%
At 2500 r/min. with no load after warming up 10 – 30%
*) MAP
(INTAKE MANIFOLD
ABSOLUTE PRESSURE) (if
equipped)At specified idle speed with no load after warming up 24 – 38 kPa, 7.1 – 11.2 in.Hg
*) THROTTLE POSITION
(RELATIVE THROTTLE
POSITION)Ignition switch ON /
warmed up engine
stoppedAccelerator pedal released 0 – 12%
Accelerator pedal depressed
fully90 – 100%
*) BAROMETRIC PRES —Barometric pressure is
displayed
) FUEL TANK LEVEL Ignition switch ON 0 – 100%
*) BATTERY VOLTAGE Ignition switch ON / engine at stop 10 – 14 V
) BRAKE SWITCH Ignition switch ONBrake pedal is released OFF
Brake pedal is depressed ON
*) FUEL SYSTEM B1
(FUEL SYSTEM STATUS)At specified idle speed after warming up CLSD (closed loop)
*) O2S B1 S1
(HEATED OXYGEN
SENSOR-1)At specified idle speed after warming up 0.1 – 0.95 V
*)
O2S B1 S2
(HEATED OXYGEN
SENSOR-2) (if equipped)At 2000 r/min. for 3 min. or longer after warming up 0.1 – 0.95 V

Downloaded from www.Manualslib.com manuals search engine Engine General Information and Diagnosis: 1A-39
*) SHORT FT B1
(SHORT TERM FUEL TRIM)At specified idle speed after warming up –20 – +20%
*) LONG FT B1
(LONG TERM FUEL TRIM)At specified idle speed after warming up –20 – +20%
) TOTAL FUEL TRIM B1 At specified idle speed after warming up –35 – +35%
) FUEL CUTEngine at fuel cut condition ON
Engine at other than fuel cut condition OFF
) O2S B1 S2 ACT
(HEATED OXYGEN
SENSOR-2) (if equipped)At specified idle speed after warming up ACTIVE
) O2S B1 S1 ACT
(HEATED OXYGEN
SENSOR-1)At specified idle speed after warming up ACTIVE
*) CANIST PRG DUTY
(EVAP CANISTER PURGE
FLOW DUTY)At specified idle speed after warming up 0%
*) IGNITION ADVANCE
(IGNITION TIMING
ADVANCE FOR NO.1
CYLINDER)At specified idle speed with no load after warming up 5 – 15° BTDC
*) EGR VALVE OPENING (if
equipped) At specified idle speed after warming up 0%
) VVT GAP
(TARGET-ACTUAL
POSITION) (VVT model)At specified idle speed after warming up 0 – 3°
) FUEL PUMPWithin 2 seconds after ignition switch ON or engine
runningON
Engine at stop with ignition switch ON OFF
) STARTER SW
(STARTER SWITCH)Ignition switch is turned to ST (engine cranking)
positionON
) A/C PRESSURE
(A/C REFERIGERANT
ABSOLUTE PRESSURE)Engine runningA/C ON (A/C is operating) at
ambient temperature: 30 °C
(86 °F) and humidity: 50%1350 – 1650 kPa For more
details, refer to pressure of
high pressure gage under “A/C
System Performance
Inspection in Section 7B”.
A/C OFF (A/C is not
operating) at ambient
temperature: 30 °C (86 °F)
and engine coolant
temperature: 90 – 100 °C
(194 – 212 °F)600 – 1000 kPa After longer
than 10 min from A/C switch
turned off
) A/C SWITCHEngine running after warming up, A/C not operating OFF
Engine running after warming up, A/C operating ON
) A/C COMP RELAY Engine runningA/C switch and blower motor
switch turned ONON
A/C switch and blower motor
switch turned OFFOFF
) BLOWER FAN Ignition switch ON
Blower fan switch: 2nd
speed position or moreON
Blower fan switch: under 1st
speed positionOFF
) ELECTRIC LOADIgnition switch ON / Headlight, small light, all turned
OFFOFF
Ignition switch ON / Headlight, small light, all turned
ONON Scan tool data Vehicle conditionNormal condition /
reference values

Downloaded from www.Manualslib.com manuals search engine 1A-40 Engine General Information and Diagnosis:
) RADIATOR FAN
(RADIATOR COOLING FAN
CONTROL RELAY)Ignition switch ONEngine coolant temp.: lower
than 97.5 °C (207.5 °F)OFF
Engine coolant temp.: 100
°C (212 °F)ON
) A/C COND FAN
(A/C CONDENSER
COOLING FAN CONTROL
RELAY)Engine runningBlower motor switch and A/C
switch turned ON/ECT over
102.5 °C (216.5 °F)ON
Blower motor switch and/or
A/C switch turned OFFOFF
) TP SENSOR 1 VOLT
(THROTTLE POSITION
SENSOR (MAIN) OUTPUT
VOLTAGE)Ignition switch ON
after warmed up
engineAccelerator pedal released 0.48 – 0.90 V
Accelerator pedal depressed
fully3.37 – 4.55 V
) TP SENSOR 2 VOLT
(THROTTLE POSITION
SENSOR (SUB) OUTPUT
VOLTAGE)Ignition switch ON
after warmed up
engineAccelerator pedal released 1.36 – 1.75 V
Accelerator pedal depressed
fully3.58 – 4.76 V
) APP SENSOR 1 VOLT
(ACCELERATOR PEDAL
POSITION (APP) SENSOR
(MAIN) OUTPUT VOLTAGE)Ignition switch ON
after warmed up
engineAccelerator pedal released 0.69 – 0.81 V
Accelerator pedal depressed
fully3.43 – 4.56 V
) APP SENSOR 2 VOLT
(ACCELERATOR PEDAL
POSITION (APP) SENSOR
(SUB) OUTPUT VOLTAGE)Ignition switch ON
after warmed up
engineAccelerator pedal released 0.31 – 0.44 V
Accelerator pedal depressed
fully1.71 – 2.29 V
*) ACCEL POSITION
(RELATIVE ACCELERATOR
PEDAL POSITION)Ignition switch ON
after warmed up
engineAccelerator pedal released 0 – 3%
Accelerator pedal depressed
fully90 – 100%
*) TARGET THROTTLE
POSI
(TARGET THROTTLE
VALVE POSITION)Ignition switch ON
after warmed up
engineAccelerator pedal released 0 – 3%
Accelerator pedal depressed
fully90 – 100%
) IAC THROTTLE
OPENING
(IDLE AIR CONTROL
THROTTLE VALVE
OPENNING)It idling with no load after warming up 5 – 25%
) THROTTLE MOTOR
VOLTIgnition switch ON / engine at stop 10.0 – 14.0 V
) CLOSED THROTTLE
POS
(CLOSED THROTTLE
POSITION)Throttle valve at idle position ON
Throttle valve opens larger than idle position OFF
) THROTTLE MOTOR
RELAYAt specified idle speed after warming up ON
*) VEHICLE SPEED At stop 0 km/h (0 mph)
) INJ PULSE WIDTH
(FUEL INJECTION PULSE
WIDTH)At specified idle speed with no load after warming up 1.5 – 3.5 msec.
At 2500 r/min. no load after warming up 1.5 – 3.0 msec. Scan tool data Vehicle conditionNormal condition /
reference values