ECU TOYOTA AVALON 2001 Service Service Manual
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 2001, Model line: AVALON, Model: TOYOTA AVALON 2001Pages: 1897, PDF Size: 26.61 MB
Page 324 of 1897
BE1DZ-02
I20800
Driver Side Junction Block
Door No.1 Fuse
Body ECU Engine Room Junction Block
Door No.2 Fuse
Front Door Lock Assembly
Rear Door Lock Assembly
Transmitter
Wireless Door Lock Control Receiver
- BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
BE-89
1693 Author: Date:
2001 AVALON (RM808U)
WIRELESS DOOR LOCK CONTROL SYSTEM
LOCATION
Page 329 of 1897
- BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
BE-99
1703 Author: Date:
2001 AVALON (RM808U)
Within
3 secs.
Turn the ignition switch from ON to LOCK at approx. 1 sec. interval 1 to 5 times to select the mode.
Pull out the key plate from the ignition key cylinder.
When add mode or rewrite mode
is selected.When confirmation
mode is selected.
ON
ONON
LOCK
LOCKLOCK
Approx.
1 sec.Approx.
1 sec. Approx. 1 sec.Approx.
1 sec.Approx.
1 sec.
Add mode
Rewrite modeConfirmation mode
ON - LOCK change occurs 1 time
ON - LOCK change occurs 2 timesON - LOCK change occurs 3 times
MPX body ECU automatically performs
the LOCK-UNLOCK operation once
or twice at 1 sec, interval to inform the
operator that either the add mode or
rewrite mode has been selected.
LOCK-UNLOCK occurs once
LOCK-UNLOCK occurs twice
Indicates that add mode has been selected.
Indicates that rewrite mode has been
selected.
1 sec.
LOCK
1 sec.1 sec.
LOCK
UNLOCK
UNLOCK
LOCK
2 secs.2 secs.
UNLOCK MPX body ECU automatically performs the
LOCK-UNLOCK operation 1 to 4 times at
2 sec. interval to inform the operator of
the number of the registered codes.
HINT:
When the number of the registered code
is 0, the operation is automatically
performed 5 times.
Example:
When the operation is performed twice, it
directs that 2 type of recognition code
have been registered.
1st time 2nd time
Registration of recognition code (Confirmation
mode and probation mode) is completed.
ON
LOCK
Approx.
1 sec.Approx.
1 sec.
Prohibition mode
ON - LOCK change occurs 5 times
When prohibition
mode is selected.
Page 330 of 1897
BE-100
- BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
1704 Author: Date:
2001 AVALON (RM808U)
MPX body performs operates LOCK-UNLOCK operation 5 times at a 1 sec.
interval to inform the operator that prohibition mode has been selected.
Press again either of switches on the transmitter.
MPX body ECU automatically performs LOCK-UNLOCK operation once or
twice at a 1 sec. interval to inform the operator that it has received the signal
from the transmitter.
LOCK-UNLOCK occurs once
LOCK-UNLOCK occurs twice Registration of recognition code is completed
Registration of recognition code has not been completed.
Recognition code received first time and second time did not match.
Proceed to continue registration
If even one of the following conditions is satisfied, registration of recognition
codes in completed.
40 secs. elapses since the MPX body ECU response.
The driver's door is closed.
The key plate is inserted in the ignition key cylinder.
4 types recognition codes are registration at one time.
Registration of recognition codes (add mode or rewrite mode) is completed.
Within
3 secs. Within
40 secs.
ON
LOCK
Approx.
1 sec.Approx.
1 sec.
When prohibition
mode is selected.
Press the lock and unlock switches on the transmitter simultaneously within 1.5 sec.
If they are not performed, the mode returns to the normal mode, then start with
ºStart registration of recognition codeº.
Proceed to finish registration
Within 40 secs.
Within 3 secs.
Page 339 of 1897
H08966
BO-76
- BODYBACK WINDOW GLASS
1861 Author: Date:
2001 AVALON (RM808U)
HINT:
Confirm that the moulding is attached to the body panel as
shown in the illustration.
(b) Hold the back window glass in place securely with a pro-
tective tape or equivalent until the adhesive hardens.
NOTICE:
Take care not to drive the vehicle during the time described
in the table below.
TemperatureMinimum time prior to driving the vehicle
35 °C (95 °F)1.5 hours
20 °C (68 °F)5 hours
5 °C (41 °F)24 hours
12. INSPECT FOR LEAK AND REPAIR
NOTICE:
Conduct a leak test after hardening time has elapsed.
13. CONNECT DEFOGGER WIRE CONNECTOR
14. INSTALL ROOF HEADLINING
15. w/ Rear personal light:
INSTALL REAR PERSONAL LIGHT
16. INSTALL UPPER BACK SILENCER
17. INSTALL PACKAGE TRAY TRIM
18. INSTALL HIGH-MOUNTED STOP LIGHT
19. INSTALL ROOF SIDE INNER GARNISH
20. INSTALL REAR SEAT (See page BO-123)
Page 419 of 1897
H12160
a
b
c
b - b a - a
c - ca
b
c
B
AB
AB BO-68
- BODYQUARTER WINDOW GLASS
1853 Author: Date:
2001 AVALON (RM808U)
5. APPLY ADHESIVE
(a) Cut off the tip of the cartridge nozzle.
Part No. 08850-00801 or equivalent
HINT:
After cutting off the tip, use all adhesive within the time de-
scribed in the table below.
TemperatureTackfree time
35 °C (95 °F)15 minutes
20 °C (68 °F)100 minutes
5 °C (41 °F)8 hours
(b) Load the cartridge into the sealer gun.
(c) Coat the glass with adhesive as shown in the illustration.
A: 8.0 mm (0.315 in.)
B: 13.5 mm (0.531 in.)
6. INSTALL QUARTER WINDOW GLASS
(a) Install the glass to the body.
(b) Hold the glass in place securely with a protective tape or
equivalent until the adhesive hardens.
NOTICE:
Take care not to drive the vehicle during the time described
in the table below.
TemperatureMinimum time prior to driving the vehicle
35 °C (95 °F)1.5 hours
20 °C (68 °F)5 hours
5 °C (41 °F)24 hours
7. INSPECT FOR LEAKS AND REPAIR
NOTICE:
Conduct a leak test after hardening time has elapsed.
8. INSTALL ROOF SIDE INNER GARNISH
9. INSTALL REAR DOOR OPENING TRIM
10. INSTALL REAR SEAT (See page BO-123)
Page 480 of 1897
BO2821
H00679
H12153
w/o Rain gutter:
H12154
a
b
b - b a - aa
b w/ Rain gutter: BO-62
- BODYWINDSHIELD
1847 Author: Date:
2001 AVALON (RM808U)
12. INSTALL WINDSHIELD GLASS AND MOULDING
(a) Install the glass, aligning the reference marks using a suc-
tion rubber.
HINT:
Check to see that the stoppers are attached to the body correct-
ly.
(b) Lightly press the glass front surface for close contact.
(c) Correct insufficient or protruded adhesive agent using a
spatula.
HINT:
Apply adhesive agent up to the windshield glass edge.
(d) Install a new windshield moulding to the windshield glass
before the adhesive agent hardens.
HINT:
Install the moulding, aligning the center of moulding with the
center of body.
(e) Remove any excessive adhesive agent before it hardens.
(f) Hold the glass and moulding in place securely with a pro-
tective tape or equivalent until the adhesive hardens.
NOTICE:
Take care not to drive the vehicle during the time described
in the table below.
TemperatureMinimum time prior to driving the vehicle
35 °C (95 °F)1.5 hours
20 °C (68 °F)5 hours
5 °C (41 °F)24 hours
13. INSPECT FOR LEAK AND REPAIR
NOTICE:
Conduct a leak test after the hardening time has elapsed.
14. w/ Sliding roof:
INSTALL SLIDING ROOF OPENING TRIM
15. INSTALL ASSIST GRIP
16. INSTALL COWL TOP VENTILATOR LOUVER
17. INSTALL HOOD TO COWL TOP SEAL
18. INSTALL WIPER ARMS
(a) Operate the wiper motor once and turn the wiper switch
OFF.
(b) Install the wiper arms and tighten nuts by hand.
Page 485 of 1897
BR0LL-05
F09731
ABS Actuator
Actuator Bracket
N´m (kgf´cm, ft´lbf) : Specified torqueCushion
CushionHolder
15 (155, 11)
15 (155, 11)
13 (130, 9)
Holder
19 (195, 14)
19 (195, 14)
Air Cleaner Assembly
W03328
ECU
Spring Plate
Actuator
N´m (kgf´cm, ft´lbf)
: Specified torque
Non-reusable part
3.0 (31, 27 in.´lbf)
- BRAKEABS ACTUATOR
BR-47
1446 Author: Date:
2001 AVALON (RM808U)
ABS ACTUATOR
COMPONENTS
Page 486 of 1897
BR0LN-03
W03326
- BRAKEABS ACTUATOR
BR-49
1448 Author: Date:
2001 AVALON (RM808U)
DISASSEMBLY
1. DISCONNECT CONNECTOR
2. REMOVE ECU
(a) Using a T20 torx wrench, loosen the 6 screws.
Torque: 3.0 N´m (31 kgf´cm, 27 in.´lbf)
NOTICE:
At the time of reassembly, tighten the screws according to
the order shown on the left.
(b) Remove the ECU and spring plate from the actuator.
NOTICE:
Protect the actuator in order to prevent sealing surface
from getting dirty and causing damage on the valve body.
If the dirt and the like are stuck to the sealing surface, use
plastic tools or soft objects to remove the dirt. Do not use
chemical solvents.
Page 508 of 1897
BR150-01
F09720
Brake Pedal Bracket Lower LH Panel Insert
Lower No. 1 Instrument Panel
Stop Light Switch
Cruise Control ECU
Pedal Pad
Clip
Return Spring
Collar
Wave Washer
Clevis Pin
Cushion Plate
Bushing
Bushing
Brake Pedal
Lithium soap base glycol grease
Non-reusable part
Brake Pedal Assembly
N´m (kgf´cm, ft´lbf) : Specified torque
13 (130, 9)
39 (400, 29)
13 (130, 9)
5.0 (51, 44 in.´lbf)
BR-8
- BRAKEBRAKE PEDAL
1407 Author: Date:
2001 AVALON (RM808U)
COMPONENTS
Page 517 of 1897
BR0L3-04
R02840
- BRAKEFRONT BRAKE CALIPER
BR-29
1428 Author: Date:
2001 AVALON (RM808U)
REMOVAL
1. REMOVE FRONT WHEEL
Remove the wheel and temporarily fasten the disc with hub
nuts.
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
2. DISCONNECT FLEXIBLE HOSE
(a) Remove the union bolt and 2 gaskets from the caliper,
then disconnect the flexible hose from the caliper.
Torque: 29 N´m (300 kgf´cm, 22 ft´lbf)
HINT:
At the time of installation, install the flexible hose lock securely
in the lock hole in the caliper.
(b) Use a container to catch the brake fluid as it drains out.
3. REMOVE CALIPER
(a) Remove the 2 installation bolts.
Torque: 34 N´m (350 kgf´cm, 25 ft´lbf)
(b) Remove the caliper from the torque plate.
4. REMOVE 2 BRAKE PADS WITH ANTI- SQUEAL
SHIMS
5. REMOVE 2 PAD SUPPORT PLATES