lock TOYOTA AYGO 2012 (in English) Manual Online

296 4-3. Do-it-yourself maintenance
AYGO_WE_99E96ETurn and secure the bulb base.
Shake the bulb base gently to
check that it is not loose, turn the
front fog lights on once and visu-
ally confirm that no light is leaking
through the mounting.
Front position lights
Turn the bulb base counterclock-
wise.
Remove the light bulb.

297 4-3. Do-it-yourself maintenance
4
Maintenance and care
AYGO_WE_99E96EFront turn signal lights
Turn the bulb base counterclock-
wise.
Remove the light bulb.
Back-up light, stop/tail lights, rear turn signal lights and rear
fog light
Open the back door and remove
the cover using a Phillips-head
screwdriver.

298 4-3. Do-it-yourself maintenance
AYGO_WE_99E96ERemoving the clip
Installing the clip
Remove the nut.
Unplug the connector while
depressing the lock release.
Remove the rear combination
lights assembly.

301 4-3. Do-it-yourself maintenance
4
Maintenance and care
AYGO_WE_99E96ETurn the bulb base counterclock-
wise and remove the cover.
Remove the light bulb.
Lights other than the above
If any of the lights listed below has burnt out, have it replaced by
any authorized Toyota dealer or repairer, or another duly qualified
and equipped professional.
Side turn signal lights
Daytime running lights (if equipped)
When installing the rubber cover of the headlight
Ensure the rubber cover is securely attached.
Fit the rubber cover outer circumfer-
ence in firmly.
Fit the rubber cover around the light
bulb in until the light bulb plug can be
seen.

302 4-3. Do-it-yourself maintenance
AYGO_WE_99E96E
LED light bulbs
The daytime running lights (if equipped) consist of a number of LEDs. If any
of the LEDs burn out, take your vehicle to any authorized Toyota dealer or
repairer, or another duly qualified and equipped professional to have the
light replaced.
Condensation build-up on the inside of the lens
Contact any authorized Toyota dealer or repairer, or another duly qualified
and equipped professional for more information in the following situations.
Temporary condensation build-up on the inside of the headlight lens does
not indicate a malfunction.
Large drops of water have built up on the inside of the lens.
Water has built up inside the headlight.
When replacing the license plate lights
Be careful not to drop the connector into the installation opening when dis-
connecting it. If the connector drops into the opening, please contact any
authorized Toyota dealer or repairer, or another duly qualified and equipped
professional, because disassembly is required to pick it up.
CAUTION
Replacing light bulbs
Turn off the lights. Do not attempt to replace the bulb immediately after
turning off the lights.
The bulbs become very hot and may cause burns.
Do not touch the glass portion of the light bulb with bare hands. Hold the
bulb by the plastic or metal portion.
If the bulb is scratched or dropped, it may blow out or crack.
Fully install light bulbs and any parts used to secure them. Failure to do so
may result in heat damage, fire, or water entering the headlight unit. This
may damage the headlights or cause condensation to build up on the lens.
To prevent damage or fire
Make sure bulbs are fully seated and locked.

5
309 5-1. Essential information
When trouble arises
AYGO_WE_99E96E
CAUTION
Caution while towing
Use extreme caution when towing the vehicle.
Avoid sudden starts or erratic driving maneuvers which place excessive
stress on the emergency towing eyelets and the cables or chains. Always
be cautious of the surroundings and other vehicles while towing.
If the engine is not running, the power assist for the brakes and steering
will not function, making steering and braking more difficult.
Installing towing eyelet to the vehicle
Make sure that towing eyelet is installed securely.
If not securely installed, towing eyelet may come loose during towing. This
may lead to accidents that cause serious injury or even death.
NOTICE
To prevent damage to the vehicle when towing using a wheel-lift type
truck
Do not tow the vehicle from the rear when the engine switch is in the
“LOCK” position or the key is removed. The steering lock mechanism is
not strong enough to hold the front wheels straight.
When raising the vehicle, ensure adequate ground clearance for towing at
the opposite end of the raised vehicle. Without adequate clearance, the
vehicle could be damaged while being towed.
To prevent body damage when towing with a sling-type truck
Do not tow with a sling-type truck, either from the front or rear.

5
311
5-1. Essential information
When trouble arises
AYGO_WE_99E96E
Fuel pump shut off system
Follow the procedure below to restart the engine after the system is
activated.
Turn the engine switch to the “ACC” or “LOCK” position.
Restart the engine.
NOTICE
Before starting the engine
Inspect the ground under the vehicle.
If you find that fuel has leaked onto the ground, the fuel system has been
damaged and is in need of repair. Do not restart the engine.
To minimize the risk of fuel leakage when the engine stalls or when
an airbag inflates upon collision, the fuel pump shut off system
stops the supply of fuel to the engine.

330
5-2. Steps to take in an emergency
AYGO_WE_99E96E
If the shift lever cannot be shifted (vehicles with a multi-mode manual transmission)
If the shift lever cannot be shifted with your foot on the brake pedal,
there may be a problem with the shift lock system (a system to pre-
vent accidental operation of the shift lever). Have the vehicle
inspected by any authorized Toyota dealer or repairer, or another
duly qualified and equipped professional immediately.
The following steps may be used as an emergency measure to
ensure that the shift lever can be shifted:
Set the parking brake.
Turn the engine switch to the “ACC” position.
Depress the brake pedal.
Press the shift lock override
button with a flathead screw-
driver or equivalent.
The shift lever can be shifted
while the button is pressed.

342 5-2. Steps to take in an emergency
AYGO_WE_99E96E
CAUTION
If the engine has to be turned off while driving
Power assist for the brakes and steering wheel will be lost, making the
brake pedal harder to depress and the steering wheel heavier to turn.
Decelerate as much as possible before turning off the engine.
Never attempt to remove the key, as doing so will lock the steering wheel.

345 6-1. Specifications
6
Vehicle specifications
AYGO_WE_99E96E3-door models
This number is also on the man-
ufacturer’s label on the right-
hand side center pillar.
5-door models
This number is also on the man-
ufacturer’s label on the right-
hand side rear pillar.
Engine number
The engine number is stamped
on the engine block as shown.