Setting TOYOTA BZ4X 2022 (in English) Workshop Manual

293
5
Owners Manual_Europe_M42D76_en
5-4. Using the driving support systems
Driving
• When a detectable object is too close
to the vehicle • When there is insufficient space to perform evasive steering maneuvers
or an obstruction exists in the evasion direction• When there is an oncoming vehicle
 The pre-collision system can be
enabled/disabled through a cus-
tomize setting. ( P.568)
The system is enabled each time the
power switch is turned to ON.
 When the system is disabled, the
PCS warning light will illuminate
and a message will be displayed
on the multi-information display.
“Pre-Collision System OFF”
 The pre-collision setting can be
changed on the customize set-
tings. ( P.568)
 When the pre-collision warning
timing is changed, the emer-
gency steering assist (excluding
the active steering function) tim-
ing will also be changed. When
“Later” is selected, the emer-
gency steering assist (excluding
the active steering function) will
not operate in most cases.
 Vehicles with a driver monitor
camera: When the system deter-
mines that the driver is not facing
forward, the pre-collision warning
and emergency steering assist
will operate at the “Earlier” tim-
ing, regardless of the user set-
ting.
 When the dynamic radar cruise
control is operating, the pre-colli-
sion warning will operate at the
“Earlier” timing, regardless of the
user setting.
Changing the pre-collision
setting

301
5
Owners Manual_Europe_M42D76_en
5-4. Using the driving support systems
Driving
• The steering wheel is not being turned
sufficiently to perform a lane change.*: Boundary between the asphalt and
grass, soil, etc., or structures, such as
a curb, guardrail, etc.
●Break suggestion function
This function is operable when all of the
following conditions are met:
• The vehicle speed is approximately 50 km/h (32 mph) or more.• The lane width is approximately 3 m
(9.8 ft.) or more.
■Temporary cancelation of functions
When the operating conditions are no longer met, a function may be temporar-
ily canceled. However, when the opera- tion conditions are met again, operation of the function will automatically be
restored. ( P.300)
■Operation of the lane departure alert function/lane departure pre-vention function
●Depending on the vehicle speed, road conditions, lane departure angle, etc.,
operation of the lane departure pre- vention function may not be felt or the function may not operate.
●Depending on the conditions, the warning buzzer may operate even if
vibration is selected through a cus- tomize setting.
●If a course* is not clear or straight, the
lane departure alert function or lane
departure prevention function may not operate.
●The lane departure alert function or lane departure prevention function may not operate if the system judges
that the vehicle is intentionally being steered to avoid a pedestrian or parked vehicle.
●It may not be possible for the system to judge if there is danger of a collision
with a vehicle in an adjacent lane.
●The steering assist operation of the
lane departure prevention function can be overridden by the steering
wheel operation of the driver.*: Boundary between the asphalt and
grass, soil, etc., or structures, such as
a curb, guardrail, etc.
■Hands off steering wheel warning
operation
In the following situations, a message urging the driver to operate the steering
wheel and an icon will be displayed and a buzzer will sound to warn the driver. When using the system, make sure to
grip the steering wheel firmly, regardless of whether the warning is operating or not.
●When the system determines that the driver is not securely holding the
steering wheel, or the steering wheel is not being operated when the steer-ing assist operation of the lane depar-
ture prevention function is operating
The length of time that the warning buzzer operates will become longer as
the frequency of the steering assist operating increases. Even if the system judges that the steering wheel has been
operated, the warning buzzer will sound for a certain amount of time.
■Break suggestion function
If the vehicle is swaying, a message will
be displayed and a warning buzzer will sound to urge the driver to take a break.

302
Owners Manual_Europe_M42D76_en
5-4. Using the driving support systems
Depending on the condition of the vehi-
cle and road surface, the break sugges- tion function may not operate.
 The LDA system can be
enabled/disabled through a cus-
tomize setting. ( P.568)
 The settings of the LDA can be
changed through on the custom-
ize settings. ( P.568)
The operating state of the lane departure alert function and st eering assist
operation of the lane departure prevention function are indicat ed.
Changing LDA settings
WARNING
■Situations in which the LDA should not be used
In the following situations, disable the LDA system. Failure to do so may lead to an accident.
●When it is necessary to disable the system: P.275
■Situations in which the system may not operate properly
In the following situations, the system
may not operate properly and the vehicle may depart from its lane. Do not overly rely on these functions. The
driver is solely responsible for paying attention to their surroundings and operating the steering wheel as nec-
essary to ensure safety.
●When the boundary between the
asphalt and grass, soil, etc., or structures, such as a curb, guard-rail, etc. is not clear or straight
●When the vehicle is struck by a crosswind or the turbulence of other
nearby vehicles
●Situations in which the lane may not
be detected: P. 2 8 1
●Situations in which the sensors may
not operate properly: P.279
●Situations in which some or all of
the functions of the system cannot operate: P. 2 8 1
Displays and system operation

307
5
Owners Manual_Europe_M42D76_en
5-4. Using the driving support systems
Driving
*1: Displayed simultaneously with a
speed limit sign.
*2: Content not recognized.
*3: If the turn signal indicators are not
operated when changing lanes, this
mark will not be displayed.
 Depending on the specifications
of the vehicle, signs may be dis-
played overlapping.
The following settings of the RSA
can be changed through customize
settings. ( P. 5 6 9 )
Ice
Supplemental mark
exists*2
Exit ramp on right*3
Exit ramp on left*3
Time
Duplicate display example
Changing RSA settings
Dynamic radar cruise
control
This dynamic radar cruise con-
trol detects the presence of
vehicles ahead, determines the
current vehicle-to -vehicle dis-
tance, and operates to main-
tain a suitable distance from
the vehicle ahead. The desired
vehicle-to-vehicle distance can
be set by operating the vehi-
cle-to-vehicle distance switch.
Use the dynamic radar cruise
control only on highways and
expressways.
WARNING
■For safe use
●Driving safely is solely the responsi- bility of the driver. Do not overly rely
on this system, and pay careful attention to the surrounding condi-tions in order to ensure safe driving.
●The dynamic radar cruise control provides driving assistance to
reduce the driver’s burden. How- ever, there are limitations to the assistance provided. Read the fol-
lowing items carefully. Do not overly rely on this system and always drive carefully.
Conditions under which the system may not operate correctly: P.313
●Set the speed appropriately accord- ing to the speed limit, traffic flow,
road conditions, weather condi- tions, etc. The driver is responsible for confirming the set speed.

310
Owners Manual_Europe_M42D76_en
5-4. Using the driving support systems
trolled stop will continue.
■Meter display
Multi-information display
Set vehicle speed
Indicators
■Switches
Driving assist switch
Driving assist mode select
switch
Cancel switch
Vehicle-to-vehicle distance
switch
“-” switch
“+” switch/“RES” switch
1 Press the driving assist mode
select switch to select dynamic
radar cruise control.
The dynamic radar cruise control indi- cator will illuminate.
2 Using the accelerator pedal,
accelerate or decelerate to the
desired vehicle speed (approxi-
mately 30 km/h [20 mph] or
more), and press the driving
assist switch to set the set vehi-
cle speed.
The set vehicle speed will be displayed on the multi-information display.
The vehicle speed at the moment the switch is released will be the set vehicle speed.
System components Setting the vehicle speed

311
5
Owners Manual_Europe_M42D76_en
5-4. Using the driving support systems
Driving
■Adjusting the set vehicle
speed using the switches
To change the set vehicle speed,
press the “+” or “-” switch until the
desired speed is displayed.
1 Increase set vehicle speed
2 Decrease set vehicle speed
Short press adjustment: Press the
switch
Long press adjustment: Press and hold
the switch until the desired set vehicle
speed is reached.
The set vehicle speed will increase
or decrease as follows:
Short press adjustment: By 1 km/h (0.6
mph) or 1 mph (1.6 km/h) each time the
switch is pressed
Long press adjustment: Increases or
decreases in 5 km/h (3.1 mph) or 5
mph (8 km/h) increments continuously
while the switch is pressed and held
The set vehicle speed adjustment
increment can be changed through a
customize setting.
■Increasing the set vehicle
speed using the accelerator
pedal
1 Depress the accelerator pedal
to accelerate the vehicle to the
desired vehicle speed.
2 Press the “+” switch.
1 Press the cancel switch or driv-
ing assist switch to cancel con-
trol.
Control will also be canceled if the brake pedal is depressed. (If the vehi-
cle has been stopped by system con- trol, depressing the brake pedal will not cancel control.)
2 Press the “RES” switch to
resume control.
Each time the switch is pressed,
the vehicle-to-vehicle distance set-
ting will change as follows:
If a preceding vehicle is detected, the
preceding vehicle mark will be dis-
played.
Adjusting the set vehicle
speed
Canceling/resuming control
Changing the vehicle-to-
vehicle distance

312
Owners Manual_Europe_M42D76_en
5-4. Using the driving support systems
The actual vehicle-to-vehicle distance
varies in accordance with the vehicle
speed. Also, when the vehicle is
stopped by system control, it will be
stopped at a certain distance from the
preceding vehicle, depending on the
situation, regardless of the setting.
■Operating conditions
●D shift position is selected.
●The desired set speed can be set when the vehicle speed is approxi-
mately 30 km/h (20 mph) or more. (If the vehicle speed is set while driving at below approximately 30 km/h [20
mph], the set speed will be set to approximately 30 km/h [20 mph].)
■Accelerating after setting the vehi-cle speed
As with normal driving, acceleration can
be performed by depressing the acceler-
ator pedal. After accelerating, the vehi- cle will return to the set vehicle speed. However, while in vehicle-to-vehicle dis-
tance control mode, the vehicle speed may decrease to below the set vehicle speed in order to maintain the distance
from the preceding vehicle.
■When the vehicle is stopped by system control during follow-up cruising
●When the “RES” switch is pressed while the vehicle is stopped by system
control, if the preceding vehicle starts off within approximately 3 seconds, follow-up cruising will resume.
●If the preceding vehicle starts off within approximately 3 seconds of the
vehicle being stopped by system con- trol, follow-up cruising will resume.
■Automatic cancelation of vehicle-to-vehicle distance control mode
In the following situations, vehicle-to- vehicle distance control mode will be canceled automatically:
●When the brake control or output restriction control of a driving support
system operates (For example: Pre- Collision System, drive-start control)
●When the parking brake has been operated
●When the vehicle is stopped by sys-tem control on a steep incline
●When any of the following are detected while the vehicle is stopped by system control:
• The driver’s seat belt is unfastened • The driver’s door is opened• Approximately 3 minutes have
elapsed since the vehicle was stopped
The parking brake may be actived auto-
matically.
The shift position may automatically change to P. ( P.250)
●Situations in which some or all of the functions of the system cannot oper-
ate: P. 2 8 1
Illustra-
tion
Number
Ve hi cl e -
to-vehi-
cle dis-
tance
Approximate Dis-
tance (Vehicle
Speed: 100 km/h
[60mph])
1Extra
long
Approximately 60
m (200 ft.)
2LongApproximately 45
m (145 ft.)
3MediumApproximately 30
m (100 ft.)
4ShortApproximately 25
m (85 ft.)

315
5
Owners Manual_Europe_M42D76_en
5-4. Using the driving support systems
Driving
system is operating, if a speed limit
sign is detected, the detected
speed limit will be displayed with an
up/down arrow. The set speed can
be increased/reduced to the
detected speed limit by pressing
and holding the “+” switch or “-”
switch.
Press and hold the “+” switch.
Press and hold the “-” switch.
■The dynamic radar cruise control with road sign assist may not oper-
ate properly when
As the dynamic radar cruise control with road sign assist may not operate prop-
erly in situations where the RSA may not operate or cannot detect signs correctly ( P.304), when using this function,
make sure to confirm the actual speed limit.
In the following situations, the set speed
may not change to the detected speed limit by pressing and holding the “+” switch or “-” switch:
●When speed limit information is not available
●When the detected speed limit is the same as the set speed
●When the detected speed limit is out-side of the speed range which the
dynamic radar cruise control system can operate
The settings of Dynamic radar
cruise control can be changed
through customize settings.
( P.568)
When the set speed is lower
than the detected speed
limit
When the set speed is
higher than the detected
speed limit
Changing Dynamic radar
cruise control settings

316
Owners Manual_Europe_M42D76_en
5-4. Using the driving support systems
■Meter display
Set vehicle speed
Cruise control indicator
■Switches
Driving assist switch
Driving assist mode select
switch
Cancel switch
“-” switch
“+” switch/“RES” switch
1 Press the driving assist mode
select switch to select cruise
control.
Cruise control
The vehicle can be driven at a
set speed even if the accelera-
tor pedal is not depressed.
Use the cruise control only on
highways and expressways.
WARNING
■For safe use
●Driving safely is solely the responsi-
bility of the driver. Therefore, do not overly rely on this system. The driver is solely responsible for pay-
ing attention to the vehicle’s sur- roundings and driving safely.
●Set the speed appropriately accord-ing to the speed limit, traffic flow, road conditions, weather condi-
tions, etc. The driver is responsible for confirming the set speed.
■Situations in which cruise con-trol should not be used
Do not use the cruise control in the
following situations. As the system will not be able to provide appropriate control, using it may lead to an acci-
dent resulting in death or serious injury.
●On roads with sharp bends
●On winding roads
●On slippery roads, such as those covered with rain, ice or snow
●On steep downhills, or where there are sudden changes between sharp
up and down gradients Vehicle speed may exceed the set speed when driving down a steep hill.
●When it is necessary to disable the system: P.275
System components
Setting the vehicle speed

319
5
Owners Manual_Europe_M42D76_en
5-4. Using the driving support systems
Driving
■Switches
Driving assist switch
Driving assist mode select
switch
Cancel switch
“-” switch
“+” switch/“RES” switch
1 Press the driving assist mode
select switch to select the speed
limiter.
The speed limiter indicator will illumi- nate in white.
2 Accelerate or decelerate to the
desired vehicle speed, and
press the driving assist switch to
set the maximum vehicle speed.
The speed limiter indicator will change
from illuminated in white to green.
The set vehicle speed will be displayed on the multi-information display in
green.If the vehicle speed is set while driving at below approximately 30 km/h (20 mph), the set vehicle speed will be
set to approximately 30 km/h (20 mph).
Press the cancel switch or driving assist switch to cancel control.
The system does not start when the shift position is R.
The system does not start when the driving assist switch is pressed continu-ously.
To change the set vehicle speed,
press the “+” or “-” switch until the
desired speed is displayed.
1 Increase set vehicle speed
Setting the maximum vehi-
cle speed
Adjusting the set vehicle
speed