TOYOTA C-HR 2018 1.G Owners Manual

912. Instrument cluster
2
Instrument cluster
C-HR_OM_USA_OM10526U
●Distance (driving range/after start)*1
Displays the estimated maximum distance that can be driven with the
quantity of fuel remaining and the distance driven after the engine was
started, respectively
• This distance is computed based on your average fuel consumption. As a result, the actual distance that can be driven may differ from that dis-
played.
• When only a small amount of fuel is added to the tank, the display may not be updated.
When refueling, turn the engine switch off. If the vehicle is refueled with-
out turning the engine switch off, the display may not be updated.
● Eco Driving Indicator Zone Display
→P. 9 4
●Speedometer
Displays the vehicle speed.
●G Monitor
→P. 9 5
●Sway warning (if equipped)
Detects the sway of the vehicle within a lane, which is often associated
with a decrease in the driver’s attention level, and displays the decrease in
attention using a bar display.
The shorter the bar length, the more the driver may need to rest.
This display is a part of the LDA (Lane Departure Alert with steering con-
trol). The display is enabled when the operating conditions of the vehicle
sway warning are met. ( →P. 226)
●Display off
A blank screen is displayed.
*1: Can be registered to Drive information 1 and 2. ( →P. 92)
*2: Resetting procedures:
• Select a function to be reset using the meter control switches and then press and hold to reset.
• If there is more than one function that can be reset, check boxes will be displayed next to those functions.

922. Instrument cluster
C-HR_OM_USA_OM10526U
The settings of the following items can be changed, refer to P. 474.
For functions that can be enabled or disabled, the function switches
between on and off each time is pressed.
● LDA (Lane Departure Alert) ( →P. 226)
Select to set up the following items. • Steering Assist on/off
• Alert sensitivity
• Sway Alert on/off
• Sway sensitivity
● PCS (Pre-Collision System) ( →P. 2 11 )
Select to set up the following items. • PCS on/off
• PCS sensitivity
● BSM (Blind Spot Monitor) ( →P. 253)
*
Select to set up the following items.
• BSM function on/off
• RCTA function on/off
*
*
: The RCTA function can be enabled/disabled only when the BSM func- tion is enabled.
● Driving mode select ( →P. 251)
Settings display

932. Instrument cluster
2
Instrument cluster
C-HR_OM_USA_OM10526U
●Vehicle Settings
Select the menu to set up the following item.
• (Tire pressure warning system) setup ( →P. 355)
Select to initialize the tire pressure warning system.
● Meter settings
Select the menu to set up the following items.
• Language
Select to change the language on the display.
•Units
Select to change the unit of measure for fuel consumption.
• (Eco Driving Indicator Light) setup
Select to activate/deactivate the Eco Driving Indicator Light
• Drive information 1 and 2
Select to select up to 2 items that will be displayed on a Drive informa-
tion screen, up to 2 Drive information screens can be set.
• Default settings
Registered or changed meter settings will be deleted or returned to their
default setting.
*: If equipped

942. Instrument cluster
C-HR_OM_USA_OM10526U
■Setting items
●“Meter Settings” and “Vehicle Settings” setting items are not selectable
during driving and cannot be operated.
Also, the settings screen is temporarily canceled in the following situations.
• A warning message is displayed.
• The vehicle starts off.
● Settings for functions not equipped to the vehicle are not displayed.
● When a function is turned off, the related settings for that function are not
selectable.
■ Pop-up display
In some situations, such as when a switch operation is performed, a pop-up
display will be temporarily displayed on the multi-information display.
■ Liquid crystal display
Small spots or light spots may appear on the display. This phenomenon is
characteristic of liquid crystal displays, and there is no problem continuing to
use the display.
■ When disconnecting and reco nnecting battery terminals
The drive information will be reset.
■ Eco Driving Indicator Zone Display
Suggests Zone of Eco driving and Eco
driving ratio based on acceleration.
Zone of Eco driving
Eco driving ratio based on accelera-
tion
If the vehicle exceeds Zone of Eco
driving, the green area disappears
and Eco Driving Indicator Light will
turn off. ( →P. 85)

952. Instrument cluster
2
Instrument cluster
C-HR_OM_USA_OM10526U■
G Monitor
■ Ending display
When the engine switch is turned off, each of the following will be displayed
on the multi-information display, and will extinguish after approximately
30 seconds.
●Elapsed time
● Distance
● Average fuel consumption
The following item is displayed.
G-force display
Displays the current G-force state.

962. Instrument cluster
C-HR_OM_USA_OM10526U
WARNING
■Caution for use while driving
● When operating the multi-information display while driving, pay extra
attention to the safety of the area around the vehicle.
● Do not look continuously at the multi-information display while driving as
you may fail to see pedestrians, objects on the road, etc. ahead of the
vehicle.
■ The information display at low temperatures
Allow the interior of the vehicle to warm up before using the liquid crystal
information display. At extremely low temperatures, the information display
monitor may respond slowly, and display changes may be delayed.
For example, there is a lag between the driver’s shifting and the new gear
number appearing on the display. This lag could cause the driver to down-
shift again, causing rapid and excessive engine braking and possibly an
accident resulting in death or injury.
■ Cautions during setting up the display
As the engine needs to be running during setting up the display, ensure that
the vehicle is parked in a place with adequate ventilation. In a closed area
such as a garage, exhaust gases including harmful carbon monoxide (CO)
may collect and enter the vehicle. This may lead to death or a serious
health hazard.
NOTICE
■While setting up the display
To prevent battery discharge, ensure that the engine is running while setting
up the display features.

97
3
Operation of
each component
C-HR_OM_USA_OM10526U 3-1. Key information
Keys .................................... 98
3-2. Opening, closing and locking the doors
Side doors ......................... 105
Back door .......................... 112
Smart key system ............. 118
3-3. Adjusting the seats Front seats ........................ 127
Rear seats......................... 128
Head restraints.................. 130
3-4. Adjusting the steering wheel and mirrors
Steering wheel .................. 133
Inside rear view mirror ...... 135
Outside rear view mirrors ............................. 137
3-5. Opening and closing the windows
Power windows ................. 140

983-1. Key information
C-HR_OM_USA_OM10526U
Keys
The following keys are provided with the vehicle.
Vehicles without a smart key system (type A)
Key (with a wireless remote
control function)
Operating the wireless remote con-
trol function (→P. 99)
Key (without a wireless remote
control function)
Key number plate
Vehicles without a smart key system (type B)
Key (with a wireless remote
control function)
Operating the wireless remote con-
trol function (→P. 99)
Key number plate
Vehicles with a smart key system
Electronic keys
• Operating the smart key system
(→P. 118)
• Operating the wireless remote
control function ( →P. 99)
Mechanical keys
Key number plate
The keys

993-1. Key information
3
Operation of each component
C-HR_OM_USA_OM10526U
Vehicles without a smart key system
Locks all the doors
(→P. 105)
Sounds the alarm ( →P. 1 0 0)
Unlocks the door (→P. 105)
Pressing the button unlocks the
driver’s door. Pressing the button
again within 3 seconds unlocks the
other doors.
Opens the windows* ( →P. 1 0 5)
*: These settings must be customized at your Toyota dealer.
Vehicles with a smart key system
Locks all the doors
(→P. 105)
Sounds the alarm ( →P. 1 0 0)
Unlocks the door (→P. 105)
Pressing the button unlocks the
driver’s door. Pressing the button
again within 3 seconds unlocks the
other doors.
Opens the windows* ( →P. 1 0 5)
*: These settings must be customized at your Toyota dealer.
Press the button to open the key.
To stow, press the button then fold
the key.
Wireless remote control
Using the key (vehicles without a smart key system)

1003-1. Key information
C-HR_OM_USA_OM10526U
To take out the mechanical key,
slide the release lever and take
the key out.
The mechanical key can only be
inserted in one direction, as the
key only has grooves on one side.
If the key cannot be inserted in a
lock cylinder, turn it over and re-
attempt to insert it.
After using the mechanical key, store it in the electronic key. Carry the
mechanical key together with the electronic key. If the electronic key bat-
tery is depleted or the entry function does not operate properly, you will
need the mechanical key. (→P. 436)
■Panic mode
■ If you lose your keys
New genuine keys can be made by your Toyota dealer using the other key
(vehicles without a smart key system) or mechanical key (vehicles with a
smart key system) and the key number stamped on your key number plate.
Keep the plate in a safe place such as your wallet, not in the vehicle.
Using the mechanical key (vehic les with a smart key system)
When is pressed for longer than
about one second, an alarm will sound
intermittently and the vehicle lights will
flash to deter any person from trying to
break into or damage your vehicle.
To stop the alarm, press any button on the
key (with a wireless remote control func-
tion) or electronic key.