warning light TOYOTA CAMRY 1999 Service Owners Manual

DI15Z±07
Supplemental Restraint System Check Sheet
Date Problem Occurred
Customer 's Name
Registration No.
Registration Year
Frame No.
Odometer Reading
Weather
Temperature
Vehicle Operation
Road Conditions
Details Of Problem
Vehicle Inspection, Repair Histo-
ry Prior to Occurrence of Mal-
function (Including Supplemen-
tal Restraint System)
Diagnosis System Inspection
SRS Warning Light
Inspection
DTC Inspection1st Time
2nd Time
1st Time
2nd TimeInspector 's
Name
Fine Cloudy Rainy Snowy Other
Approx.
Starting Idling
Driving [ Constant speed Acceleration Deceleration
Other ]
Remains ON Sometimes Light Up Does Not Light Up
Remains ON Sometimes Light Up
Does Not Light Up
Normal Code Malfunction Code
Normal Code Malfunction Code[ Code. ]
[ Code. ]km
Miles //
//
// Date Vehicle Brought In
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±625
860 Author: Date:
CUSTOMER PROBLEM ANALYSIS CHECK

DI4L1±01
H02309
R13006
DLC1
E1 Tc
DI±626
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
861 Author: Date:
PRE±CHECK
1. SRS WARNING LIGHT CHECK
(a) Turn the ignition switch to the ACC or ON position and
check that the SRS warning light lights up.
(b) Check that the SRS warning light goes out after approx.
6 seconds.
HINT:

When the ignition switch is at ACC or ON and the SRS
warning light remains on or flashes, the airbag sensor as-
sembly has detected a malfunction code.

If, after approx. 6 seconds have elapsed, the SRS warn-
ing light sometimes lights up or the SRS warning light
lights up even when the ignition switch is OFF, a short in
the SRS warning light circuit can be considered likely.
Proceed to ºSRS warning light circuit malfunctionº on
page DI±790, DI±792.
2. DTC CHECK (Using diagnosis check wire)
(a) Present troubles codes:
Output the DTC.
(1) Turn the ignition switch to the ACC or ON position
and wait for approx. 20 seconds.
(2) Using SST, connect terminals Tc and E1 of the
DLC1.
SST 09843±18020
NOTICE:
Pay due attention to the terminal connecting position to
avoid a malfunction.
(b) Past troubles codes:
Output the DTC.
(1) Using service wire, connect Terminals Tc and E1 of
the DLC1.
SST 09843±18020
(2) Turn the ignition switch to the ACC or ON position
and wait for approx. 20 seconds.
NOTICE:
Pay due attention to the terminal connecting position to
avoid a malfunction.

AT0716AB0056H08231
Normal Code
ON
OFF0.25
0.25
Code 11 and 31
ON
OFF
0.5 2.54.0
1.5 0.5
DTC 11
DTC 31Repeat
H08398S05331H08323
TOYOTA Hand±Held Tester
DLC1
DLC3
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±627
862 Author: Date:
(c) Read the DTC.
Read the 2±digit DTC as indicated by the number of times
the SRS warning light blinks. As an example, the blinking
patterns, normal, 11 and 31 are shown in the illustration.

Normal code indication
The light will blink 2 times per second.

Malfunction code indication
The first blinking output indicates the first digit
of a 2±digit DTC. After a 1.5±second pause,
the second blinking output will indicate the
second digit.
If there are 2 or more codes, there will be a 2.5±second pause
between each code. After all the codes have been output, there
will be a 4.0±second pause and they will all be repeated.
HINT:

In the event of a number of trouble codes, indication will
start from the smallest numbered code.

If a DTC is not output or a DTC is output without terminal
connection, proceed to the Tc terminal circuit inspection
on page DI±796.
3. DTC CHECK (Using TOYOTA hand±held tester)
(a) Hook up the TOYOTA hand±held tester to the DLC1 or
the DLC3.
(b) Read the DTCs by following the prompts on the tester
screen.
HINT:
Please refer to the TOYOTA hand±held tester operator's manu-
al for further details.
4. DTC CLEARANCE (Not using service wire)
When the ignition switch is turned off, the diagnostic trouble
code is cleared.
HINT:
DTC might not be cleared by turning the ignition switch OFF.
In this case, proceed to the next step.
5. DTC CLEARANCE (Using service wire)
(a) Connect the 2 service wires to terminals Tc and AB of
DLC1.
(b) Turn the ignition switch to ACC or ON and wait for approx.
6 seconds.

H01461
H02309
H02271
ABTerminal
Tc
ABOFF
Body
Ground
OFF
ON
OFF
Several
Seconds50 m sec.
50 m sec.
1 seconds
(± 0.5 sec.)
Tc
Body
Ground
1 seconds
(± 0.5 sec.)
1
23
45
DI±628
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
863 Author: Date:
(c) Starting with the Tc terminal, ground alternately terminal
Tc and terminal AB twice each in cycles of 1.0 seconds.
Make sure that the terminals are grounded. Ensure the
terminal Tc remain grounded.
HINT:
When alternately grounding terminals Tc and AB, release
ground from one terminal and immediately ground the other ter-
minal within an interval of 0.2 seconds.
If DTCs are not cleared, repeat the above procedure until the
codes are cleared.
(d) Several seconds after doing the clearing procedure, the
SRS warning light will blink in a 50 m sec. cycle to indicate
the codes which have been cleared.
6. Past troubles codes:
DTC CLEARANCE
(See step 5.)

DI1AZ±04
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±633
868 Author: Date:
DIAGNOSTIC TROUBLE CODE CHART
If a malfunction code is displayed during the DTC check, check the circuit listed for that code in the table
below (Proceed to the page given for that circuit.).
DTC No.
(See Page)Detection ItemTrouble AreaSRS
Warning Light
B0100/13
(DI±640)

Short in D squib circuit
Steering wheel pad (squib)

Spiral cable

Airbag sensor assembly

Wire harness
ON
B0101/14
(DI±645)

Open in D squib circuit
Steering wheel pad (squib)

Spiral cable

Airbag sensor assembly

Wire harness
ON
B0102/11
(DI±649)

Short in D squib circuit (to Ground)
Steering wheel pad (squib)

Spiral cable

Airbag sensor assembly

Wire harness
ON
B0103/12
(DI±653)

Short in D squib circuit (to B+)
Steering wheel pad (squib)

Spiral cable

Airbag sensor assembly

Wire harness
ON
B0105/53
(DI±657)
Short in P squib circuit
Front passenger airbag assembly (squib)

Airbag sensor assembly

Wire harness
ON
B0106/54
(DI±661)
Open in P squib circuit
Front passenger airbag assembly (squib)

Airbag sensor assembly

Wire harness
ON
B0107/51
(DI±664)
Short in P squib circuit (to Ground)
Front passenger airbag assembly (squib)

Airbag sensor assembly

Wire harness
ON
B0108/52
(DI±667)
Short in P squib circuit (to B+)
Front passenger airbag assembly (squib)

Airbag sensor assembly

Wire harness
ON
TMC made:
B0110/43
(DI±670)
Short in side squib (RH) circuit
Side airbag assembly RH (squib)

Airbag sensor assembly

Wire harness
Blink
TMMK made:
B0110/43
(DI±674)
Short in side squib (RH) circuit
Side airbag assembly RH (squib)

Airbag sensor assembly

Wire harness

Sub wire harness
Blink
TMC made:
B0111/44
(DI±679)
Open in side squib (RH) circuit
Side airbag assembly RH (squib)

Airbag sensor assembly

Wire harness
Blink
TMMK made:
B0111/44
(DI±682)
Open in side squib (RH) circuit
Side airbag assembly RH (squib)

Airbag sensor assembly

Wire harness

Sub wire harness
Blink
TMC made:
B0112/41
(DI±686)
Short in side squib (RH) circuit
(to Ground)
Side airbag assembly RH (squib)

Airbag sensor assembly

Wire harness
Blink

DI±634
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
869 Author: Date:
DTC No.
(See Page)Detection ItemTrouble AreaSRS
Warning Light
TMMK made:
B0112/41
(DI±689)
Short in side squib (RH) circuit
(to Ground)
Side airbag assembly RH (squib)

Airbag sensor assembly

Wire harness

Sub wire harness
Blink
TMC made:
B0113/42
(DI±693)
Short in side squib (RH) circuit
(to B+)
Side airbag assembly RH (squib)

Airbag sensor assembly

Wire harness
Blink
TMMK made:
B0113/42
(DI±696)
Short in side squib (RH) circuit
(to B+)
Side airbag assembly RH (squib)

Airbag sensor assembly

Wire harness

Sub wire harness
Blink
TMC made:
B0115/47
(DI±700)
Short in side squib (LH) circuit
Side airbag assembly LH (squib)

Airbag sensor assembly

Wire harness
Blink
TMMK made:
B0115/47
(DI±704)
Short in side squib (LH) circuit
Side airbag assembly LH (squib)

Airbag sensor assembly

Wire harness

Sub wire harness
Blink
TMC made:
B0116/48
(DI±709)
Open in side squib (LH) circuit
Side airbag assembly LH (squib)

Airbag sensor assembly

Wire harness
Blink
TMMK made:
B0116/48
(DI±712)
Open in side squib (LH) circuit
Side airbag assembly LH (squib)

Airbag sensor assembly

Wire harness

Sub wire harness
Blink
TMC made:
B0117/45
(DI±716)
Short in side squib (LH) circuit
(to Ground)
Side airbag assembly LH (squib)

Airbag sensor assembly

Wire harness
Blink
TMMK made:
B0117/45
(DI±719)
Short in side squib (LH) circuit
(to Ground)
Side airbag assembly LH (squib)

Airbag sensor assembly

Wire harness

Sub wire harness
Blink
TMC made:
B0118/46
(DI±723)
Short in side squib (LH) circuit
(to B+)
Side airbag assembly LH (squib)

Airbag sensor assembly

Wire harness
Blink
TMMK made:
B0118/46
(DI±726)
Short in side squib (LH) circuit
(to B+)
Side airbag assembly LH (squib)

Airbag sensor assembly

Wire harness

Sub wire harness
Blink
B0130/63
(DI±730)
Short in P/T squib (RH) circuit
Seat belt pretensioner RH (squib)

Airbag sensor assembly

Wire harness
Blink
B0131/64
(DI±734)
Open in P/T squib (RH) circuit
Seat belt pretensioner RH (squib)

Airbag sensor assembly

Wire harness
Blink
B0132/61
(DI±737)
Short in P/T squib (RH) circuit
(to Ground)
Seat belt pretensioner RH (squib)

Airbag sensor assembly

Wire harness
Blink
B0133/62
(DI±740)
Short in P/T squib (RH) circuit
(to B+)
Seat belt pretensioner RH (squib)

Airbag sensor assembly

Wire harness
Blink

± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±635
870 Author: Date:
DTC No.
(See Page)Detection ItemTrouble AreaSRS
Warning Light
B0135/73
(DI±743)
Short in P/T squib (LH) circuit
Seat belt pretensioner LH (squib)

Airbag sensor assembly

Wire harness
Blink
B0136/74
(DI±747)
Open in P/T squib (LH) circuit
Seat belt pretensioner LH (squib)

Airbag sensor assembly

Wire harness
Blink
B0137/71
(DI±750)
Short in P/T squib (LH) circuit
(to Ground)
Seat belt pretensioner LH (squib)

Airbag sensor assembly

Wire harness
Blink
B0138/72
(DI±753)
Short in P/T squib (LH) circuit
(to B+)
Seat belt pretensioner LH (squib)

Airbag sensor assembly

Wire harness
Blink
B1100/31
(DI±756)
Airbag sensor assembly malfunction
Airbag sensor assemblyON
B1140/32
(DI±758)
Side airbag sensor assembly (RH)
malfunction
Side airbag sensor assembly (RH)

Wire harnessBlink
B1141/33
(DI±766)
Side airbag sensor assembly (LH)
malfunction
Side airbag sensor assembly (LH)

Wire harnessBlink
B1156/B1157/
15
(DI±774)
Front airbag sensor (RH) malfunction
Front airbag sensor (RH)

Wire harness

Engine room main wire harness
ON
B1158/B1159/
16
(DI±782)
Front airbag sensor (LH) malfunction
Front airbag sensor (LH)

Wire harness
ON
Nl
System normal±OFFNormal
(DI±787)
Voltage source drop
Battery

Airbag sensor assemblyON
HINT:

When the SRS warning light remains lit up and the DTC is the normal code, this means a voltage source
drops.
This malfunction is not stored in memory by the airbag sensor assembly and if the power source volt-
age returns to normal, the SRS warning light will automatically go out.

When 2 or more codes are indicated, the codes will be displayed in numeral order starting from the
lowest numbered code.

If a code not listed on the chart is displayed, the airbag sensor assembly is faulty.

DI1B0±04
H08283
Combination Meter
(Warning Light)Steering Wheel Pad
(with Airbag)
Airbag Sensor AssemblyFront Passenger
Airbag Assembly
Side Airbag Assembly
(LH)
Side Airbag Sensor
Assembly (LH)
Seat Belt
Pretensioner (LH)Side Airbag Assembly (RH)
Side Airbag Sensor Assembly (RH)
Seat Belt
Pretensioner (RH) Front Airbag
Sensor (LH)Front Airbag Sensor (RH)
Spiral Cable
DI±636
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
871 Author: Date:
PARTS LOCATION

DI1B1±08
H01357
C18
C17C19
287 8 9 10 16 17
18A B12 3 4 5 6
11 12 15 14 13
AABB
19 20 21 22 23 24 25 26 27 1 2 3 4 5 6
7 8 9 10 11 121 2 3 4 5 6
7 8 9 10 11 12
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±637
872 Author: Date:
TERMINALS OF ECU
No.SymbolTerminal Name
A±Electrical Connector Check Mechanism
B±Electrical Connector Check Mechanism
C18 ± 3LASRS Warning Light
C18 ± 5IG2Power Source (IGN Fuse)
C18 ± 6ACCPower Source (CIG Fuse)
C18 ± 9SR+Front Airbag Sensor (RH)
C18 ± 10P+Squib (Passenger)
C18 ± 11P±Squib (Passenger)
C18 ± 12SILDiagnosis
C18 ± 13D±Squib (Driver)
C18 ± 14D+Squib (Driver)
C18 ± 15SL+Front Airbag Sensor (LH)
C18 ± 19TcDiagnosis
C18 ± 20SR±Front Airbag Sensor (RH)
C18 ± 26SL±Front Airbag Sensor (LH)
C18 ± 27E1Ground
C18 ± 28E2Ground
C17 ± 1PL±Squib (Seat Belt Pretensioner, LH)
C17 ± 2PL+Squib (Seat Belt Pretensioner, LH)
C17 ± 5SFL+Squib (Side, LH)
C17 ± 6SFL±Squib (Side, LH)
C17 ± 7VUPLSide Airbag Sensor (LH)
C17 ± 9SSL+Side Airbag Sensor (LH)
C17 ± 10FSLSide Airbag Sensor (LH)
C17 ± 12ESLSide Airbag Sensor (LH)

DI164±18
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±639
874 Author: Date:
PROBLEM SYMPTOMS TABLE
Proceed with troubleshooting of each circuit in the table below.
SymptomSuspect AreaSee page

With the ignition switch in ACC or ON position, the SRS warning
light sometimes lights up after approx. 6 seconds have elapsed.
SRS warning light circuit
(Al li ht h i iti it h i i LOCK iDI 790
SRS warning light is always lit up even when ignition switch is in
the LOCK position.(Always lights up when ignition switch is in LOCK posi-
tion.)DI±790

With the ignition switch in ACC or ON position, the SRS warning
light does not light up.
SRS warning light circuit
(Does not light up when ignition switch is turned to ACC or
ON.)
DI±792

DTC is not displayed.

SRS warning light is always lit up at the time of DTC check pro-
cedure.
Tc terminal circuitDI±796

DTC is displayed without Tc and E1 terminal connection.