TOYOTA CAMRY V20 1986 Service Information

No. 1 lock ball assembly lock nut
No. 2 lock ball assembly
Filler plug
Drain plug
Back±up light switch
Side bearing retainer
Clutch release bearing retainer
Straight screw plug (Shit fork shaft)
(Reverse restrict piny
Transaxle x Engine (10 mm bolt)
(12 mm bolt)
Left engine mounting
Drive shaft center bearing bracket
Drive shaft X Side gear shaft
Steering knuckle x Lower arm
Engine mounting center member x Body
Engine mounting center member x Engine Mounting
Engine mounting center member x Lower crossmember
Lower cross member x Body
Torque Specifications (Cont'd)
Part tightened
± SERVICE SPECIFICATIONSManual Transaxle (S51)A±5

TRANSMISSION ASSEMBLY
Input shaft
Roller bearing journal diameter
3rd gear journal diameter
4th gear journal diameter
Runout
Output shaft
1 st gear journal diameter
2nd gear bushing diameter
Runout
Gear thrust clearance
Shift fork to hub sleeve clearance
Synchronizer ring to gear clearance
Oil pump assembly
Rotor body clearance
MANUAL TRANSAXLE (E56F5)
Specifications
Input shaft snap ring thickness
No.2 clutch hub Gear oil clearance
1 st and 4th gear
Rotor tip clearance2nd and 3rd gear
Side clearance
5th gear
± SERVICE SPECIFICATIONSManual Transaxle (E56F5)A±6

DIFFERENTIAL ASSEMBLY
Differential side bearing preload (at starting)
New bearing
Reused bearing
No. 1 case bushing inner diameter
Differential No. 1 case backlash
Front differential case backlash
Differential No.2 case thrust clearance
Front differential case thrust clearance
Thrust washer thickness
For No. 1 case side gear Input shaft snap ring thickness (cont'd)
4th gear and rear bearing
Conical spring washer height
For No. 1 case Front case outer diameter
No. 1 case side
Specifications (Cont'd)
No±2 case bushing inner diameter
No.2 case side
For No.2 case
± SERVICE SPECIFICATIONSManual Transaxle (E56F5)A±7

Shim thickness
For differential side bearing preload Thrust washer thickness (cont'd)
For front case side gear
Specifications (Cont'd)
For No. 2 case and front case For No±2 case side gear
± SERVICE SPECIFICATIONSManual Transaxle (E56F5)A±8

TRANSFER ASSEMBLY
Ring gear runout
Ring gear mounting case runout
Ring gear backlash
Driven pinion preload (at starting)Shim thickness (cont'd)
For differential side bearing preload (cont'd)
Transfer total prreload (at starting)
(Add driven pinion preload)
Specifications (Cont'd)
Adjusting shim thickness
For ring gear backlash
± SERVICE SPECIFICATIONSManual Transaxle (E56F5)A±9

Oil pump x Cover
Ring gear x Differential case
Ring bearing retainer x Transmission case
Transmission case x Transaxfe case
Oil pump assembly x Transaxle case
Shift fork x Shaft
Oil pipe X Housing
Transmission case x Transmission case cover
Shift and select lever shaft assembly x
Transmission case
Belicrank x Transmission case
Back±up light switch X Transmission case
Driven pinion x Bearing cage
Ring gear x Ring gear mounting case
Driven pinion cage x Transfer case
Transfer left case x Transfer right case
Transfer left case x Inspection hole cover
Differential lock sleeve x Shift fork
Transfer right case x Transfer case cover
Driven pinion cage x Extension housing
Extension housing x Dynamic damper
Transaxle assembly x Transfer assembly
Differential lock indicator switch X Transfer left case
Output shaft assembly x Lock nut
Transfer left case x Plug (Large)
Transfer left case x Plug (Small)
Transmission case x Plug
Transfer left case X Drain plug
Reverse idler gear retaining bolt
Oil cooler pipe elbow X Transaxle
Oil cooler pipe x Elbow
Specifications (Cont'd)
Adjusting shim thickness (cont'd)
For tooth contact
Torque Specifications
Part tightened
± SERVICE SPECIFICATIONSManual Transaxie (E56F5)A±10

Shift and select lever X Transmission case
Lock bolt x Transmission case
Engine front mounting X Transaxle
Stiffener plate
Engine rear end plate
Engine mounting left bracket x Transaxle
Transfer right case x Actuator bracket
Transaxle assembly x Engine
Input shaft _
3rd and 4th gear journal diameter
5th gear journal diameter
Runout
Output shaft
Roller bearing journal diameter
1 st and 2nd gear journal diameter
Runout
Gear thrust clearance
MANUAL TRANSAXLE (E52)
Specifications
Shift fork to hub sleeve clearance
Synchronizer ring to gear clearane
Output shaft bearing preload (at starting)
Torque Specifications (Cont'd)
Gear oil clearance
1 st and 4thPart tightened
Reverse idler 2nd and 3rd
5th
± SERVICE SPECIFICATIONSManual Transaxle (E56F5)A±11

Shift and select lever X Transmission case
Lock bolt x Transmission case
Engine front mounting X Transaxle
Stiffener plate
Engine rear end plate
Engine mounting left bracket x Transaxle
Transfer right case x Actuator bracket
Transaxle assembly x Engine
Input shaft _
3rd and 4th gear journal diameter
5th gear journal diameter
Runout
Output shaft
Roller bearing journal diameter
1 st and 2nd gear journal diameter
Runout
Gear thrust clearance
MANUAL TRANSAXLE (E52)
Specifications
Shift fork to hub sleeve clearance
Synchronizer ring to gear clearane
Output shaft bearing preload (at starting)
Torque Specifications (Cont'd)
Gear oil clearance
1 st and 4thPart tightened
Reverse idler 2nd and 3rd
5th
± SERVICE SPECIFICATIONSManual Transaxle (E52)A±11

Tight plug drive in depth
Control shaft cover oil seal drive on depth
Input shaft snap ring thickness
No. 2 clutch hubSpeedometer driven gear oil seal drive in depth
Oil pump
Body clearance
Output shaft snap ring thickness
No. 1 clutch hub
Specifications (Cont'd)
Side bearing preload (at starting)
Input rear bearingSide clearance Tip clearance
± SERVICE SPECIFICATIONSManual Transaxle (E52)A±12

Differential pinion to side gear backlash
Differential runout
Differential side gear thrust washer thicknessOutput shaft snap ring thickness (cont'd)
No. 3 clutch hub
Output shaft rear bearing adjusting shim thickness
Specifications (Cont'd)
± SERVICE SPECIFICATIONSManual Transaxle (E52)A±13