high beam TOYOTA COROLLA iM 2018 Owners Manual (in English)

3
1
8 7
6
5
4
3
2
9
COROLLA iM_U (OM12M42U)4-1. Before driving
Driving the vehicle ............. 110
Cargo and luggage............ 120
Vehicle load limits ............. 123
Trailer towing..................... 124
Dinghy towing (vehicles with a
continuously variable
transmission)................... 125
Dinghy towing (vehicles with a manual
transmission)................... 126
4-2. Driving procedures Engine (ignition) switch ..... 128
Continuously variable transmission .................... 131
Manual transmission ......... 137
Turn signal lever................ 139
Parking brake .................... 140
4-3. Operating the lights and wipers
Headlight switch ................ 141
Windshield wipers and washer ............................ 145
Rear window wiper and washer ............................ 147
4-4. Refueling Opening the fuel tank cap .......................... 149 4-5. Using the driving
support systems
Toyota Safety Sense C...... 153
PCS (Pre-Collision System)..... 159
LDA (Lane Departure Alert)..... 172
Automatic High Beam ........ 177
4-6. Using the driving support systems
Cruise control .................... 181
Driving assist systems ........................... 186
4-7. Driving tips Winter driving tips .............. 192
5-1. Using the air conditioning system
and defogger
Automatic air conditioning system ......... 196
5-2. Using the interior lights Interior lights list................. 203
• Front interior light/front personal lights ............... 204
• Rear interior light ........... 205
• Vanity lights ................... 205
4Driving
5Interior features

722. Instrument cluster
COROLLA iM_U (OM12M42U)
The indicators inform the driver of the operating state of the vehicle’s
various systems.
*1: These lights turn on when the engine switch is turned to the “ON” position to indicate that a system check is being performed. They will turn off after
the engine is started, or after a few seconds. There may be a malfunction
in a system if a light does not come on, or turn off. Have the vehicle
inspected by your Toyota dealer.
*2: The light flashes to indicate that the system is operating.
*3: The light does not turn on when the system is disabled.
*4: This light illuminates on the center panel.
Indicators
Turn signal indicator
(→P. 139)*1VSC OFF indicator
(→P. 188)
(U.S.A.)
Headlight indicator
(→P. 141)*1, 3, 6Eco Driving Indicator
Light ( →P. 81)
(Canada)
Tail light indicator
(→P. 141) *4Security indicator
(→P. 66)
Headlight high beam
indicator ( →P. 141)
*6Sport mode indicator
(→P. 132)
*1, 6Automatic High Beam
indicator ( →P. 177)*5Low outside tempera-
ture indicator ( →P. 74)
Cruise control indicator
( →P. 181)
*1, 4“AIR BAG ON/OFF” indi-
cator ( →P. 45)
Cruise control “SET”
indicator ( →P. 181)
*6LDA (Lane Departure
Alert) indicator
(→P. 172)
*1, 2
Slip indicator ( →P. 187)*1, 6, 7PCS warning light
(→P. 159)

109
4Driving
COROLLA iM_U (OM12M42U)4-1. Before driving
Driving the vehicle ............. 110
Cargo and luggage ........... 120
Vehicle load limits ............. 123
Trailer towing..................... 124
Dinghy towing (vehicles with a
continuously variable
transmission)................... 125
Dinghy towing (vehicles with a manual
transmission)................... 126
4-2. Driving procedures Engine (ignition) switch ..... 128
Continuously variable transmission .................... 131
Manual transmission ......... 137
Turn signal lever................ 139
Parking brake .................... 140 4-3. Operating the lights
and wipers
Headlight switch ................ 141
Windshield wipers and washer ............................ 145
Rear window wiper and washer ............................ 147
4-4. Refueling Opening the fuel tank cap .......................... 149
4-5. Using the driving support systems
Toyota Safety Sense C ..... 153
PCS (Pre-Collision System) .... 159
LDA (Lane Departure Alert) .... 172
Automatic High Beam ....... 177
4-6. Using the driving support systems
Cruise control .................... 181
Driving assist systems ...... 186
4-7. Driving tips Winter driving tips ............. 192

1424-3. Operating the lights and wipers
COROLLA iM_U (OM12M42U)
Ty p e BThe headlights, day-
time running lights ( →P.
143) and all the lights
listed below turn on and
off automatically.
(When the engine
switch is in the “ON”
position)
The side marker, park-
ing, tail, license plate,
instrument panel lights,
and daytime running
lights ( →P. 143) turn
on.
The headlights and all
the lights listed above
(except daytime run-
ning lights) turn on.
The daytime running lights turn on. ( →P. 143)
With the headlights on, push
the lever away from you to turn
on the high beams.
Pull the lever toward you to the
center position to turn the high
beams off.
Pull the lever toward you and
release it to flash the high
beams once.
You can flash the high beams with the headlights on or off.
1
2
3
Turning on the high beam headlights
4
1
2

153
4
Driving
COROLLA iM_U (OM12M42U)
4-5. Using the driving support systems
◆PCS (Pre-Collision System)
→P. 1 5 9
◆LDA (Lane Departure Alert)
→P. 1 7 2
◆Automatic High Beam
→P. 1 7 7
Toyota Safety Sense C∗
∗: If equipped
The Toyota Safety Sense C consists of the following drive assist
systems and contributes to a safe and comfortable driving expe-
rience:
WARNING
■Toyota Safety Sense C
The Toyota Safety Sense C is designed to operate under the assumption
that the driver will drive safely, and is designed to help reduce the impact to
the occupants and the vehicle in the case of a collision or assist the driver in
normal driving conditions.
As there is a limit to the degree of recognition accuracy and control perfor-
mance that this system can provide, do not overly rely on this system. The
driver is always responsible for paying attention to the vehicle's surround-
ings and driving safely.

1774-5. Using the driving support systems
4
Driving
COROLLA iM_U (OM12M42U)
Push the lever away from you with
the headlight switch in
position.
The Automatic High Beam indica-
tor will come on when the head-
lights are turned on automatically
to indicate that the system is
active.
Automatic High Beam∗
∗: If equipped
The Automatic High Beam uses an in-vehicle front sensor to
assess the brightness of streetlights, the lights of vehicles
ahead etc., and automatically turns the high beam on or off as
necessary.
WARNING
■ Limitations of the Automatic High Beam
Do not rely on the Automatic High Beam. Always drive safely, taking care to
observe your surroundings and turning the high beam on or off manually if
necessary.
■ To prevent incorrect operation of the Automatic High Beam system
Do not overload the vehicle.
Activating the Automatic High Beam system

1784-5. Using the driving support systems
COROLLA iM_U (OM12M42U)■
Switching to low beam
Pull the lever to original posi-
tion.
The Automatic High Beam indi-
cator will turn off.
Push the lever away from you to
activate the Automatic High
Beam system again.
■
Switching to high beam
Turn the light switch to
position.
The Automatic High Beam indi-
cator will turn off and the high
beam indicator will turn on.
Turning the high beam on/off manually

1794-5. Using the driving support systems
4
Driving
COROLLA iM_U (OM12M42U)
■When “Headlight System Malfunction Vi sit Your Dealer” is displayed on
the multi-information display
The system may be malfunctioning. Have the vehicle inspected by your
Toyota dealer immediately.
■ High beam automatic turning on or off conditions
●When all of the following conditions are fulfilled, the high beam will be auto-
matically turned on (after approximately 1 second):
• Vehicle speed is approximately 21 mph (33 km/h) or more.
• The area ahead of the vehicle is dark.
• There are no vehicles ahead with headlights or tail lights turned on.
• There are few streetlights on the road ahead.
● If any of the following conditions is met, the high beams will turn off automat-
ically:
• Vehicle speed is below approx imately 17 mph (27 km/h).
• The area ahead of the vehicle is not dark.
• Vehicles ahead have their headlights or tail lights turned on.
• There are many streetlights on the road ahead.
■ Front sensor detection information
●The high beam may not be automatically turned off in the following situa-
tions:
• When vehicles ahead suddenly appear from a curve
• When the vehicle is cut in front of by another vehicle
• When vehicles ahead are hidden from sight due to repeated curves, road
dividers or roadside trees
• When vehicles ahead appear from the faraway lane on wide road
• When vehicles ahead have no lights
● The high beam may be turned off if a vehicle ahead that is using fog lights
without using the headlights is detected.
● House lights, street lights, traffic signals, and illuminated billboards or signs
may cause the high beam to switch to the low beams, or the low beams to
remain on.
● The following factors may affect the amount of time taken to turn the high
beam on or off:
• The brightness of headlights, fog lights, and tail lights of vehicles ahe\
ad
• The movement and direction of vehicles ahead
• When a vehicle ahead only has operational lights on one side
• When a vehicle ahead is a two-wheeled vehicle
• The condition of the road (gradient, curve, condition of the road surface,
etc.)
• The number of passengers and amount of luggage
● The high beam may be turned on or off when the driver does not expect it.
● Bicycles or similar objects may not be detected.

1804-5. Using the driving support systems
COROLLA iM_U (OM12M42U)●
In the situations shown below, the system may not be able to accurately
detect surrounding brightness levels. This may cause the low beams to
remain on or the high beams to cause problems for pedestrians, vehicles
ahead or other parties. In these cases, manually switch between the high
and low beams.
• In bad weather (rain, snow, fog, sandstorms, etc.)
• The windshield is obscured by fog, mist, ice, dirt, etc.
• The windshield is cracked or damaged.
• The front sensor is deformed or dirty.
• The front sensor temperature is extremely high.
• Surrounding brightness levels are equal to those of headlights, tail lights
or fog lights.
• Vehicles ahead have headlights or tail lights that are either switched off,
dirty, are changing color, or are not aimed properly.
• When driving through an area of in termittently changing brightness and
darkness.
• When frequently and repeatedly driving ascending/descending roads, or roads with rough, bumpy or uneven surfaces (such as stone-paved
roads, gravel tracks, etc.).
• When frequently and repeatedly taking curves or driving on a winding road.
• There is a highly reflective object ahead of the vehicle, such as a sign or
a mirror.
• The back of a vehicle ahead is highly reflective, such as a container on a truck.
• The vehicle’s headlights are damaged or dirty, or are not aimed properly.
• The vehicle is listing or titling due to a flat tire, a trailer being towed, etc.
• The high beam and low beam are repeatedly being switched between in an abnormal manner.
• The driver believes that the high beam may be causing problems or dis-
tress to other drivers or pedestrians nearby.

3027-2. Steps to take in an emergency
COROLLA iM_U (OM12M42U)
Take the appropriate actions as instructed in the message displayed.
If any of the following messages are displayed, also refer to this
Owner’s Manual.
■If “Front Camera Unavailable” or “Front Camera Vision
Blocked Clean and Demist Windshield” is displayed (if
equipped)
The following systems may be suspended until the problem shown
in the message is resolved.
● PCS (Pre-Collision system)
● LDA (Lane Departure Alert)
● Automatic High Beam
■If “Maintenance Required Soon” is displayed (U.S.A. only)
Indicates that all maintenance according to the driven distance on
the maintenance schedule
* should be performed soon.
Comes on approximately 4500 miles (7200 km) after the message
has been reset.
If necessary, perform maintenance.
*: Refer to the separate “Scheduled Maintenance Guide” or “Owner’s Manual Supplement” for the maintenance interval applicable to your vehicle.
■
If “Maintenance Required Visit Your Dealer” is displayed
(U.S.A. only)
Indicates that all maintenance is required to correspond to the
driven distance on the maintenance schedule
*.
Comes on approximately 5000 miles (8000 km) after the message
has been reset.
(The indicator will not work pro perly unless the message has been
reset.)
Perform the necessary maintenance. Please reset the message
after the maintenance is performed. ( →P. 227)
*: Refer to the separate “Scheduled Maintenance Guide” or “Owner’s Manual
Supplement” for the maintenance interval applicable to your vehicle.
■ Warning buzzer
In some cases, the buzzer may not be heard because of noisy place or an
audio sound.
Other messages displayed on th e multi-information display