Axle TOYOTA LAND CRUISER 1996 J80 Workshop Manual

SA1VS−01
SA−11 6
−
SUSPENSION AND AXLE COIL SPRING AND REAR SHOCK ABSORBER
1996 LAND CRUISER (RM451U)
DISPOSAL
DISCARD SHOCK ABSORBER
Before discarding the shock absorber, drill a hole 2 − 3 mm
(0.079 − 0.118 in.) in diameter at the location shown in the il-
lustration to release the gas inside.
NOTICE:
When drilling, chips may fly out, work carefully. The gas is
colorless, odorless and non −poisonous.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1VT−01
−
SUSPENSION AND AXLE COIL SPRING AND REAR SHOCK ABSORBER
SA−11 7
1996 LAND CRUISER (RM451U)
INSTALLATION
Installation is in the reverse order of removal (See page SA−11 3 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1VU−01
SA−11 8
−
SUSPENSION AND AXLE REAR LATERAL CONTROL ROD
975
Author: Date:
1996 LAND CRUISER (RM451U)
REAR LATERAL CONTROL ROD
REMOVAL
1. REMOVE REAR WHEEL
Torque:
Steel wheel: 147 N·m (1,500 kgf·cm, 109 ft·lbf)
Aluminum wheel: 103 N·m (1,050 kgf·cm, 76 ft·lbf)
2. REMOVE LATERAL CONTROL ROD
(a) Remove the bolt, nut and plate washer, and disconnect the lateral control rod.
Torque: 177 N·m (1,800 kgf·cm, 130 ft·lbf)
HINT:
After stabilizing the suspension, torque the bolt.
(b) Remove the bolt and lateral control rod from the axle housing.
Torque: 245 N·m (2,500 kgf·cm, 181 ft·lbf)
HINT:
After stabilizing the suspension, torque the bolt.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1VV−01
R13240
SST
SST
R13241
SST
SST
−
SUSPENSION AND AXLE REAR LATERAL CONTROL ROD
SA−11 9
1996 LAND CRUISER (RM451U)
REPLACEMENT
REPLACE LATERAL CONTROL ROD BUSHING
(a) Using SST and a press, remove the bushing.
SST 09550−10012 (09553 −10010),
09710 −22021 (09710 −01071)
(b) Using SST and a press, install a new bushing. SST 09550−10012 (09553 −10010),
09710 −22021 (09710 −01071)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1VW−01
SA−120
−
SUSPENSION AND AXLE REAR LATERAL CONTROL ROD
1996 LAND CRUISER (RM451U)
INSTALLATION
Installation is in the reverse order of removal (See page SA−11 8 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1VX−01
−
SUSPENSION AND AXLE REAR UPPER AND LOWER CONTROL ARM
SA−121
978
Author: Date:
1996 LAND CRUISER (RM451U)
REAR UPPER AND LOWER
CONTROL ARM
REMOVAL
1. REMOVE REAR WHEEL
Torque:
Steel wheel: 147 N·m (1,500 kgf·cm, 109 ft·lbf)
Aluminum wheel: 103 N·m (1,050 kgf·cm, 76 ft·lbf)
2. REMOVE UPPER CONTROL ARM
Remove the 2 bolts, plate washers, nuts and upper control arm
from the frame. Torque: 177 N·m (1,800 kgf·cm, 130 ft·lbf)
HINT:
After stabilizing the suspension, torque the bolt.
3. REMOVE LOWER CONTROL ARM
Remove the 2 bolts, plate washers, nuts and lower control arm
from the frame. Torque: 177 N·m (1,800 kgf·cm, 130 ft·lbf)
HINT:
After stabilizing the suspension, torque the bolt.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1VY−01
R13242
SST
R13243
SSTSST
R13244
SST
W02078
SST
SA−122
−
SUSPENSION AND AXLE REAR UPPER AND LOWER CONTROL ARM
1996 LAND CRUISER (RM451U)
REPLACEMENT
1. REPLACE UPPER CONTROL ARM BUSHING
(a) Using SST and a press, remove the bushing. SST 09226 −10010, 09950 −60010 (09951 −00490),
09950 −70010 (09951 −07100)
(b) Using SST and a press, install a new bushing. SST 09226−10010, 09506 −35010
2. REPLACE LOWER CONTROL ARM BUSHING
(a) Using SST and a press, remove the bushing. SST 09506 −35010, 09950 −60010 (09951 −00540),
09950 −70010 (09951 −07100)
(b) Using SST and a press, install a new bushing, as shown.
SST 09316−20011, 09506 −35010
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1VZ−01
−
SUSPENSION AND AXLE REAR UPPER AND LOWER CONTROL ARM
SA−123
1996 LAND CRUISER (RM451U)
INSTALLATION
Installation is in the reverse order of removal (See page SA−121 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1W0−01
SA−124
−
SUSPENSION AND AXLE REAR STABILIZER BAR
981
Author: Date:
1996 LAND CRUISER (RM451U)
REMOVAL
REMOVE STABILIZER BAR
(a) Loosen the 2 bolts and nuts.
Torque: 25 N·m (260 kgf·cm, 19 ft·lbf)
HINT:
After stabilizing the suspension, torque the nut.
(b) Remove the nuts and disconnect the stabilizer bar with the links from the bracket.
Torque: 15 N·m (153 kgf·cm, 11 ft·lbf)
HINT:
After stabilizing the suspension, torque the nut.
(c) Remove the 2 bolts, nuts and links from the stabilizer bar.
(d) Remove the 4 bolts and stabilizer bar from the axle hous- ing with the covers.
Torque: 18 N·m (185 kgf·cm, 13 ft·lbf)
HINT:
After stabilizing the suspension, torque the bolt.
(e) Remove the 2 covers and cushions from the stabilizer bar.
HINT:
Install the cushions and brackets touching the line painted on
the stabilizer bar.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1W1−01
−
SUSPENSION AND AXLE REAR STABILIZER BAR
SA−125
1996 LAND CRUISER (RM451U)
INSTALLATION
Installation is in the reverse order of removal (See page SA−124 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010