brake sensor TOYOTA LAND CRUISER 1996 J80 User Guide
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 1996, Model line: LAND CRUISER, Model: TOYOTA LAND CRUISER 1996 J80Pages: 1399, PDF Size: 41.35 MB
Page 398 of 1399
BR1DP−02
−
BRAKE REAR SPEED SENSOR
BR−65
1047
Author: Date:
1996 LAND CRUISER (RM451U)
REAR SPEED SENSOR
COMPONENTS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 399 of 1399
BR1DQ−02
BR−66
−
BRAKE REAR SPEED SENSOR
1996 LAND CRUISER (RM451U)
REMOVAL
HINT:
When replacing the sensor or sensor harness, replace the sen-
sor and sensor harness together as a set.
1. DISCONNECT SPEED SENSOR CONNECTOR
(a) Disconnect the speed sensor connector.
(b) Remove the 3 clamp bolts and 2 clips holding the sensor wire harness from the suspension arm and frame.
2. REMOVE SPEED SENSOR
Remove the installation bolt and speed sensor from the axle
end. Torque: 18 N·m (185 kgf·cm, 13 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 400 of 1399
BR1NO−01
R04775
−
BRAKE REAR SPEED SENSOR
BR−67
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT SPEED SENSOR
(a) Disconnect the speed sensor connector.
(b) Measure the resistance between terminals.
Resistance: 0.5 − 1.6 kΩ
If resistance value is not specified, replace the sensor.
(c) Check there is no continuity between each terminal and sensor body.
If there is continuity, replace the sensor.
(d) Connect the speed sensor connector.
2. INSPECT SENSOR INSTALLATION
Check the sensor installation bolt is tightened properly and
there is no clearance between the sensor and axle end.
If not, tighten the bolt. Torque: 18 N·m (185 kgf·cm, 13 ft·lbf)
3. VISUALLY INSPECT SENSOR ROTOR SERRATIONS
(a) Remove the brake disc (See page BR−40).
(b) Inspect the sensor rotor serrations for scratches, cracks,
warping or missing teeth.
(c) Install the brake disc.
NOTICE:
To prevent damage to the serrations, do not strike the axle
hub.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 401 of 1399
BR−68
−
BRAKE REAR SPEED SENSOR
1996 LAND CRUISER (RM451U)
4. CHECK THAT THERE IS NO FOREIGN OBJECT ON
SENSOR
5. CHECK SPEED SENSOR SIGNAL (See page DI−210 )
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 402 of 1399
BR1DR−01
−
BRAKE REAR SPEED SENSOR
BR−69
1996 LAND CRUISER (RM451U)
INSTALLATION
Installation is in the reverse order of removal (See page BR−66 ).
HINT:
After installation, check the speed sensor signal (see page DI−190).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 625 of 1399
DI5LT−02
Vehicle Brought to Workshop
Customer Problem Analysis
P. DI−189
Check and Clear DTC (Pre−check)
P.
DI−190
Items inside are titles of pages in this manual,
with the page number in the bottom portion. See
the indicated pages for detailed explanations.
Problem Symptom ConfirmationSymptom Simulation
P. IN−18
Symptom
does not occur
Symptom
occurs
DTC Check
P. DI−190
Sensor CheckCircuit Inspection
P. DI−201 − DI−235
DTC Chart
P. DI−196
Malfunction codeProblem Symptoms Table
P. DI−200
Check for Fluid Leakage
P. DI−237
Identification of Problem
Normal code
Repair
Confirmation Test
End
1
2
3
4
5
6 7
8 9
10 11 Step 8: Diagnostic steps permitting the use of the
TOYOTA hand−held tester or TOYOTA
breake −out−box.
DI−188
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
355
Author: Date:
1996 LAND CRUISER (RM451U)
ANTI−LOCK BRAKE SYSTEM
HOW TO PROCEED WITH TROUBLESHOOTING
Troubleshoooting in accordance with the procedure on the following pages.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 629 of 1399
N09348
Interface BoxHarness VehicleTOYOTA
Tester
Hand
−held
TOYOTA Break −out− box
F00007
DLC1
Ts Tc
E
1
BR3904
0.25 sec. 0.25 sec.
ON
OFF
DI−192
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
1996 LAND CRUISER (RM451U)
(d) Using TOYOTA break −out− box and TOYOTA hand− held
tester, measure the ECU terminal values.
(1) Hook up the T OYOTA hand−held tester and TOYO-
TA break−out−box to the vehicle.
(2) Read the ECU input/output values by following the prompts on the tester screen.
HINT:
TOYOTA hand −held tester has a ”Snapshot ” function. This re-
cords the measured values and is effective in the diagnosis of
intermittent problems.
Please refer to the TOYOTA hand−held tester/TOYOTA break
out−box operators manual for further details.
2. SPEED SENSOR SIGNAL AND DECELERATION SEN-
SOR CHECK
(a) Check the speed sensor signal. (1) Conform that the center differential is free.
(2) Turn the ignition switch OFF.
(3) Using SST, connect terminals Ts and E
1 of the
DLC1.
SST 09843−18020
(4) Start the engine.
(5) Check that the ABS warning light blinks.
HINT:
If the ABS warning light does not blink, inspect the ABS warning
light circuit (See page DI−230).
(6) Drive vehicle straight forward.
HINT:
Drive vehicle faster than 45 km/h (28 mph) for several seconds.
(7) Stop the vehicle.
(8) Using SST, connect terminals Tc and E
1 of the
DLC1.
SST 09843−18020
(9) Read the number of blinks of the ABS warning light.
HINT:
See the list of DTC on page DI−190 .
If every sensor is normal, a normal code is output (A cycle of
0.25 sec. ON and 0.25 sec. OFF is repeated).
If 2 or more malfunction are indicated at the same time, the low-
est numbered code will be displayed 1st.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 630 of 1399
BR3893
Malfunction Code (Example Code 72, 76)
72 6
7
ON
OFF
0.5 sec.
0.5 sec.
0.5 sec.
0.5 sec. 1.5 sec.
2.5 sec. 4 sec.
Repeat
F00007
E1
Ts
DLC1
R05599
0.13 sec.
0.13 sec.
3 sec.
ON
OFF
R05037
860
30 mm
33.86 1.18 in.
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
DI−193
1996 LAND CRUISER (RM451U)
(10) After doing the check, disconnect terminals Ts and
E
1, Tc and E1 of the DLC1, and turn the ignition
switch OFF.
(b) Deceleration sensor detection point check. (1) Confirm that the center differential is free.
(2) Turn the ignition switch OFF.
(3) Using SST, connect terminals Ts and E
1 of the
DLC1.
SST 09843−18020
(4) Start the engine.
(5) Check that the ABS warning light blinks.
HINT:
If the ABS warning light does not blink, inspect the ABS warning
light circuit (See page DI−230).
(6) Jack up the rear side of the vehicle slowly.
HINT:
When measuring the height, measure at the center of the lower
body of the vehicle. (7) Check that the warning light blinks.
If the warning light turns on, inspect the deceleration sensor
installation. If the sensor installation is OK, replace the decel-
eration sensor. (8) Jack down the vehicle slowly.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 631 of 1399
R05038
780 30 mm
30.71 1.18 in.
BR1865
0.13 sec.
0.13 sec.
ON
OFF
R05596
0.13 sec.
Braking
0.13 sec.
R05597
0.13 sec. 0.13 sec.
Braking
DI−194
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
1996 LAND CRUISER (RM451U)
(9) Jack up the front side of the vehicle slowly, as
shown.
HINT:
When measuring the height, measure at the center of the lower
body of the vehicle. (10) Check that the warning light blinks.
If the warning light turns on, inspect the deceleration sensor
installation. If the sensor installation is OK, replace the decel-
eration sensor.
(11) Jack down the vehicle slowly.
(c) Deceleration sensor operation check. (1) Drive the vehicle straight ahead at about 20 km/h
(12.4 mph) or more, lightly depress the brake pedal.
(2) Check that there is no change in the warning light pattern.
(3) Drive the vehicle straight ahead at about 20 km/h (12.4 mph) or more, and depress the brake pedal
moderately.
(4) Check that the warning light turns on while braking.
(5) Drive the vehicle straight ahead at about 20 km/h (12.4 mph) or more, and depress the brake pedal
strongly.
(6) Check that the warning light pattern changes while braking, as shown.
If the operation is not as specified, inspect the deceleration sen-
sor installation. If the sensor installation is OK, replace the de-
celeration sensor. (7) Stop the vehicle and turn the ignition switch OFF.
(8) Remove SST from the terminals Ts and E
1 of the
DLC1.
SST 09843−18020
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 632 of 1399
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
DI−195
1996 LAND CRUISER (RM451U)
(d) Check the DTC of speed sensor function.
Code No.DiagnosisTrouble Area
71Low output voltage of right front speed sensor
Right front speed sensor
Sensor installation
Sensor rotor
Sensor wire harness
72Low output voltage of left front speed sensor
Left front speed sensor
Sensor installation
Sensor rotor
Sensor wire harness
73Low output voltage of right rear speed sensor
Right rear speed sensor
Sensor installation
Sensor rotor
Sensor wire harness
74Low output voltage of left rear speed sensor
Left rear speed sensor
Sensor installation
Sensor rotor
Sensor wire harness
75Abnormal change in output voltage of right front speed sen-
sorRight front speed sensor rotor
Sensor wire harness
76Abnormal change in output voltage of left front speed sen-
sorLeft front speed sensor rotor
Sensor wire harness
77Abnormal change in output voltage of right rear speed sen-
sorRight rear speed sensor rotor
Sensor wire harness
78Abnormal change in output voltage of left rear speed sensorLeft rear speed sensor rotor
Sensor wire harness
79Deceleration sensor is faultyDeceleration sensor
Sensor installation
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010