engine oil TOYOTA LAND CRUISER 1996 J80 User Guide

BE4917
Test LED
Battery
BE1217
Warning Light
Ignition
Switch Battery
N01212
BE−38
−
BODY ELECTRICAL COMBINATION METER
1996 LAND CRUISER (RM451U)
(c) Ground terminal on the wire harness side through a 3.4
W test bulb.
(d) Turn the ignition switch ON, and check that the bulb lights
up and that the receiver gauge needle moves to the high
side.
If operation is not as specified, measure the receiver gauge re-
sistance.
14. INSPECT OIL PRESSURE RECEIVER GAUGE RESIS- TANCE
Measure the receiver gauge resistance between terminals. Resistance:
40 − 48 Ω
If resistance value is not as specified, replace the receiver
gauge.
15. INSPECT OIL PRESSURE SENDER GAUGE OPERA-
TION
(a) Disconnect the connector from the sender gauge.
(b) Apply battery positive voltage to the sender gauge termi- nal through a test LED.
(c) Check that the bulb does not light when the engine is stopped.
(d) Check that the LED flashes when the engine is running. The number of flashed should vary with engine speed.
If operation is not as specified, replace the sender gauge.
16. INSPECT BRAKE WARNING LIGHT
(a) Disconnect the connectors from the level warning switch and parking brake switch.
(b) Connect terminals on the wire harness side connector of
the level warning switch connector.
(c) Turn the ignition switch ON, and check that the warning light lights up.
17. INSPECT PARKING BRAKE SWITCH
(a) Check that there is continuity between terminal and the switch set nut with switch pin released (parking brake le-
ver pulled up).
(b) Check that there is no continuity between terminal and the switch set nut with switch pin pushed in. (parking
brake lever released)
If operation is not as specified, replace the switch.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE−40
−
BODY ELECTRICAL COMBINATION METER
1996 LAND CRUISER (RM451U)
23. INSPECT SEAT BELT WARNING RELAY CIRCUIT
Disconnect the connector from the relay and inspect the con-
nector on the wire harness side, as shown in the chart.
Tester connectionConditionSpecified condition
1 − GroundConstantContinuity
4 − GroundDriver’s seat belt position UNFASTENContinuity
4 − GroundDriver’s seat belt position FASTENNo continuity
7 − GroundIgnition key SETContinuity
7 − GroundIgnition key RemoveNo continuity
8 − GroundDriver’s door position OPENContinuity
8 − GroundDriver’s door position CLOSENo continuity
5 − GroundIgnition switch position ONBattery positive voltage
5 − GroundIgnition switch position LOCK or ACCNo voltage
9 − GroundConstantBattery positive voltage
If circuit is as specified, try another relay.
If the circuit is not as specified, check the circuits connected to
other parts.
24. INSPECT ENGINE OIL LEVEL WARNING SWITCH
(a) Check that there is continuity between terminal with the
switch each position.
(b) Heat the switch to above 60° C (140°F) in an oil bath.
(c) Check that there is continuity between terminals with the switch ON (float up).
(d) Check that there is no continuity between terminals with
the switch OFF (float down).
If operation is not as specified, replace the switch.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Z06300
BrightDark 2
3
Extinguished
1
−
BODY ELECTRICAL COMBINATION METER
BE−41
1996 LAND CRUISER (RM451U)
25. INSPECT ENGINE OIL LEVEL WARNING CIRCUIT
Disconnect the switch connector and inspect the connector on
wire harness side, as shown.
Tester connectionConditionSpecified condition
2 − GroundConstantContinuity
If continuity is not as specified, inspect the wire harness or
ground point.
26. INSPECT ENGINE OIL LEVEL WARNING LIGHT
(a) Disconnect the connector from the switch.
(b) Ground terminal 1 on the wire harness connector.
(c) Turn the ignition switch ON, and check that the warning
light lights up approximately 40 seconds later.
If the warning light does not light up, inspect bulb or wire har-
ness.
27. INSPECT LIGHT CONTROL RHEOSTAT
(a) Connect terminals 1 and 3 through a 3.4 W test bulb.
(b) Connect the positive (+) lead from the battery to terminal
1 and the negative ( −) lead to terminal 2.
(c) Turn the rheostat knob to fully counterclockwise, and
check that the test bulb goes out.
(d) Gradually turn the rheostat knob to clockwise, and check
that the test bulb brightness changes from dark to bright.
If operation is not as specified, replace the rheostat.
HINT:
Adjust the brightness of illumination lights by rheostat.
A/C Control Assembly
Antenna Switch
Ash Receptacle
Audio
Center Diff. Lock Switch
Cigarette Lighter
Defogger Switch
Hazard Warning Switch
Shift Lever
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P03788
CORRECT WRONG
Clearance
Z00038
Nippondenso Borroughs
−
CHARGING CHARGING SYSTEM
CH−3
1996 LAND CRUISER (RM451U)
(b) Check the fusible link and fuses for continuity.
Fusible link
MAIN 2.0 A
AM1 1.25 B
AM2 0.3 P
H−fuseAM1 50 A
FuseIGN 7.5 A
GAUGE 15 A
3. INSPECT DRIVE BELTS
(a) Visually check the drive belt for cracks, oiliness or wear.
Check that the belt does not touch the bottom of the pulley
groove.
If necessary, replace the drive belts as a set.
(b) Using a belt tension gauge, measure the belt tension. Belt tension gauge:
Nippondenso BTG−20 (95506 −00020)
Borroughts No. BT−33−73F
Drive belt tension:
New belt400 − 580 N (41.0 − 59.1 kgf, 90.4 − 130.2 lbf)
Used belt200 − 390 N (20.4 − 40.0 kgf, 45.0 − 88.2 lbf)
If the belt tension is not as specified, adjust it.
HINT:
”New belt” refers to a belt which has been used less than
5 minutes on a running engine.
”Used belt” refers to a belt which has been used on a run-
ning engine for 5 minutes or more.
After installing a new belt, run the engine for about 5 min-
utes and recheck the belt tension.
4. VISUALLY CHECK GENERATOR WIRING AND LIS- TEN FOR ABNORMAL NOISES
(a) Check that the wiring is in good condition.
(b) Check that there is no abnormal noise from the generator
while the engine is running.
5. INSPECT DISCHARGE WARNING LIGHT CIRCUIT
(a) Turn the ignition switch ”ON”. Check that the discharge warning light comes on.
(b) Start the engine. Check that the light goes off.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

CO0IO−04
−
COOLING COOLANT
CO−1
696
Author: Date:
1996 LAND CRUISER (RM451U)
COOLANT
INSPECTION
HINT:
Check the coolant level when the engine is cold.
1. CHECK ENGINE COOLANT LEVEL AT RADIATOR RESERVOIR
The engine coolant level should be between the ”LOW” and ”FULL”\
lines.
If low, check for leaks and add engine coolant up to the ”FULL” line.
2. CHECK ENGINE COOLANT QUALITY
(a) Remove the radiator cap.
CAUTION:
To avoid the danger of being burned, do not remove the radiator cap while the engine and radiator
are still hot, as fluid and steam can be blown out under pressure.
(b) There should not be any excessive deposits of rust or scale around the r\
adiator cap or radiator filler
hole, and the coolant should be free from oil.
If excessively dirty, replace the coolant.
(c) Reinstall the radiator cap.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

CO112−01
CO−4
−
COOLING WATER PUMP
1996 LAND CRUISER (RM451U)
REMOVAL
1. DRAIN ENGINE COOLANT
2. DISCONNECT NO.3 WATER BYPASS HOSE
3. DISCONNECT RADIATOR INLET HOSE
4. REMOVE DRIVE BELTS, FAN WITH FLUID COU- PLING, WATER PUMP PULLEY AND FAN SHROUD
(a) Stretch the belts and loosen the water pump pulley mounting nuts.
(b) Loosen the lock, pivot and adjusting bolts of the genera- tor, and remove the drive belts.
(c) Disconnect the oil cooler hose from the clamp on the fan shroud.
(d) Remove the 2 bolts holding the fan shroud to the radiator.
(e) Remove the 4 water pump pulley mounting nuts.
(f) Pull out the fan with fluid coupling, water pump pulley and
fan shroud.
(g) Remove the fan from the fluid coupling.
5. REMOVE WATER PUMP
Remove the 4 bolts, 2 nuts, water pump and gasket.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

CO114−02
CO−6
−
COOLING WATER PUMP
1996 LAND CRUISER (RM451U)
INSTALLATION
1. INSTALL WATER PUMP
Install a new gasket and the water pump with the 4 bolts and 2
nuts. Torque: 21 N·m (210 kgf·cm, 15 ft·lbf)
2. INSTALL WATER PUMP PULLEY, FAN SHROUD, FAN WITH FLUID COUPLING AND DRIVE BELTS
(a) Install fan to the fluid coupling.
(b) Place the fan with fluid coupling, water pump pulley and fan shroud in position.
(c) Temporarily install the fan pulley mounting nuts.
(d) Install the fan shroud with the 2 bolts. Torque: 5.0 N·m (50 kgf·cm, 43 in.·lbf)
(e) Connect the oil cooler hose to the clamp on the fan
shroud.
(f) Install the drive belts with the adjusting bolt and pivot bolt.
(g) Stretch the belts tight and tighten the 4 water pump pulley mounting nuts.
(h) Adjust the drive belts (See page CH−2 ).
3. CONNECT NO.3 WATER BYPASS HOSE
4. CONNECT RADIATOR INLET HOSE
5. FILL RADIATOR WITH ENGINE COOLANT
6. START ENGINE AND CHECK FOR LEAKS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

CO117−02
CO−14
−
COOLING RADIATOR
1996 LAND CRUISER (RM451U)
REMOVAL
1. DRAIN ENGINE COOLANT
2. REMOVE BATTERY AND BATTERY TRAY
(a) Disconnect the battery cables.
(b) Remove the nuts, hold −down clamp and battery.
(c) Remove the bolt and disconnect the ground strap.
(d) Remove the 5 bolts and battery tray.
3. REMOVE RADIATOR GRILLE
Remove the 5 screws, clip and radiator grille.
4. DISCONNECT NO.3 WATER BYPASS HOSE
5. DISCONNECT RADIATOR INLET HOSE
6. DISCONNECT RADIATOR RESERVOIR HOSE
7. REMOVE RADIATOR
(a) Stretch the belts and loosen the water pump pulley mounting nuts.
(b) Loosen the lock, pivot and adjusting bolts of the genera- tor, and remove the drive belts.
(c) Disconnect the oil cooler hose from the clamp on the fan shroud.
(d) Remove the 2 bolts holding the fan shroud to the radiator.
(e) Remove the 4 water pump pulley mounting nuts.
(f) Pull out the fan with fluid coupling, water pump pulley and
fan shroud.
8. DISCONNECT A/T OIL COOLER HOSES
9. DISCONNECT RADIATOR OUTLET HOSE
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

CO118−01
CO−16
−
COOLING RADIATOR
1996 LAND CRUISER (RM451U)
INSTALLATION
1. INSTALL RADIATOR
(a) Install the 2 radiator brackets with the 4 nuts. Torque: 12 N·m (120 kgf·cm, 9 ft·lbf)
(b) Install the radiator with the 2 bolts and 2 nuts. Torque:
Bolt: 18 N·m (185 kgf·cm, 13 ft·lbf)
Nut: 12 N·m (120 kgf·cm, 9 ft·lbf)
2. CONNECT A/T OIL COOLER HOSES
3. CONNECT RADIATOR OUTLET HOSE
4. INSTALL WATER PUMP PULLEY, FAN SHROUD, FAN WITH FLUID COUPLING AND DRIVE BELTS
(a) Place the fan with fluid coupling, water pump pulley and fan shroud in position.
(b) Temporarily install the fan pulley mounting nuts.
(c) Install the fan shroud with the 2 bolts. Torque: 5.0 N·m (50 kgf·cm, 43 in.·lbf)
(d) Connect the oil cooler hose to the clamp on the fan
shroud.
(e) Install the drive belts with the adjusting bolt and pivot bolt.
(f) Stretch the belts tight and tighten the 4 water pump pulley mounting nuts.
(g) Adjust the drive belts (See page CH−2 ).
5. CONNECT RADIATOR RESERVOIR HOSE
6. CONNECT RADIATOR INLET HOSE
7. CONNECT NO.3 WATER BYPASS HOSE
8. INSTALL RADIATOR GRILLE
Install the radiator grille with the 5 screws and clip.
9. INSTALL BATTERY AND BATTERY TRAY
(a) Install the battery tray with the 5 bolts.
(b) Connect the ground strap with the bolt.
(c) Install the battery with the hold−down clamp and nuts.
(d) Connect the battery cables.
10. FILL RADIATOR WITH ENGINE COOLANT
11. START ENGINE AND CHECK FOR LEAKS
12. CHECK AUTOMATIC TRANSMISSION FLUID LEVEL
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P04771
InsideOutside
DI−8
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
6. BASIC INSPECTION
When the malfunction code is not confirmed in the DTC check, troubleshooting\
should be performed in the
order for all possible circuits to be considered as the causes of the problem\
s. In many cases, by carrying
out the basic engine check shown in the following flow chart, the location \
causing the problem can be found
quickly and efficiently. Therefore, use of this check is essential in engine troubleshooting.
1 Is battery positive voltage 11 V or more when engine is stopped?
NO Charge or replace battery.
YES
2 Is engine cranked?
NO Proceed to page ST−16 , and continue to trouble-
shoot.
YES
3 Does engine start?
NO Go to step 7.
YES
4 Check air filter.
PREPARATION:
Remove air filter.
CHECK:
Visually check that the air cleaner element is not dirty or exces-
sive oily.
HINT:
If necessary, clean the element with compressed air. First blow
from inside thoroughly, then blow from outside of element.
NG Repair or replace
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010