display TOYOTA LAND CRUISER 1996 J80 Owner's Manual

DI5LW−03
DI−196
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
1996 LAND CRUISER (RM451U)
DIAGNOSTIC TROUBLE CODE CHART
NOTICE:
When removing the part, turn the ignition switch OFF.
HINT:
Using SST 09843 −18020, connect the terminals Tc and E1, and remove the short pin.
If any abnormality is not found when inspection parts, inspect the ECU.
If a malfunction code is displayed during the DTC check, check the circu\
it listed that the code. For details
of each code, turn to the page referred to under the ”See page” for respective ”DTC N\
o.” in the DTC chart.
DTC No.
(See page)Detection Item Trouble Area
11
( DI−201 )Open circuit in ABS control (solenoid) relay circuitABS control (solenoid) relay
 Open or short in ABS control (solenoid) relay circuit
12
( DI−201 )Short circuit in ABS control (solenoid) relay circuitABS control (solenoid) relay
 B+ short in ABS control (solenoid) relay circuit
13
( DI−204 )Open circuit in ABS control (motor) relay circuitABS control (motor) relay
 Open or short in ABS control (motor) relay circuit
14
( DI−204 )Short circuit in ABS control (motor) relay circuitABS control (motor) relay
 B+ short in ABS control (motor) relay circuit
21
( DI−207 )Open or short circuit in 3 −position solenoid circuit for right front
wheel ABS actuator
 Open or short in SFR circuit
22
( DI−207 )Open or short circuit in 3− position solenoid circuit for left front
wheel ABS actuator
 Open or short in SFLcircuit
23
( DI−207 )Open or short circuit in 3− position solenoid circuit for rear
wheel ABS actuator
 Open or short in SRR circuit
31
( DI−210 )Right front wheel speed sensor signal malfunction
Right front, left front, right rear and left rear speed sensor
 Open or short in each speed sensor circuit
 Senser rotor32
( DI−210 )Left front wheel speed sensor signal malfunction
33
( DI−210 )Right rear wheel speed sensor signal malfunction
34
( DI−210 )Left rear wheel speed sensor signal malfunction
35
( DI−210 )Open circuit in left front or right rear speed sensor circuitOpen in left front or right rear speed sensor circuit
36
( DI−210 )Open circuit in right front or left rear speed sensor circuitOpen in right front or left rear speed sensor circuit
41
( DI−215 )Low battery positive voltage or abnormally high battery
positive voltageBattery
 IC regulator
 Open or short in power source circuit
43
( DI−218 )Malfunction in deceleration sensorDeceleration sensor
 Wire harness for deceleration sensor circuit
44
( DI−219 )Open or short in deceleration sensor circuitDeceleration sensor
 Open or short in deceleration sensor circuit
48
( DI−221 )Open or short circuit in center differential lock circuit
Center differential is lockingCenter differential lock
 Center differential lock circuit
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5LZ−03
DI−200
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
1996 LAND CRUISER (RM451U)
PROBLEM SYMPTOMS TABLE
If a normal code is displayed during the DTC check but the problem still o\
ccurs, check the circuits for each
problem symptom in the order given in the table below and proceed to the releva\
nt troubleshooting page.
SymptomsSuspected AreaSee page
ABS does not operate
Only when 1 − 4 are all normal and the problem is still occurring, replace the ABS
ECU
2. Check the DTC reconfirming that the normal code is output
3. IG power source circuit
4. Speed sensor circuit
5. Check the ABS actuator with a checker
If abnormal, check the hydraulic circuit for leakage (See page DI−237)
DI−190
DI−215
DI−210
BR−53
ABS does not operate effi-
ciently
Only when 1 − 4 are all normal and the problem is still occurring, replace the ABS
ECU
1. Check the DTC reconfirming that the normal code is output
2. Speed sensor circuit
3. Stop light switch circuit
4. Check the ABS actuator with a checker
If abnormal, check the hydraulic circuit for leakage (See page DI−237)
DI−190
DI−210
DI−228
BR−53
ABS warning light abnormal1. ABS warning light circuit
2. ABS ECUDI−230 −
DTC check cannot be done
Only when 1 and 2 are all normal and the problem is still occurring, rep\
lace the
ABS ECU
1. ABS warning light circuit
2. Tc terminal circuit
DI−230
DI−233
Speed sensor signal check
cannot be done1. Ts terminal circuit
2. ABS ECUDI−235−
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−226
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
1 Is DTC output?
Check DTC on page DI−190 .
YES Repair circuit indicated by code output.
NO
2 Is normal code displayed?
YES Check ABS solenoid relay. Check for short in harness and connector between ABS solenoid
relay and DLC1 (See page IN−28 ).
NO
3 Is ABS warning light go off?
YES Check for open or short in harness and connec-
tor between ECU−IG fuse and ECU (See page
IN−28 ).
NO
4 Check battery positive voltage.
PREPARATION:
Start the engine.
CHECK:
Check the battery positive voltage.
OK:
Voltage: 10 − 16 V NG Check and repair charging system.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

W02200
BR−BE1Tc
3 11
DLC1
B−YIH1 ABS ECU
Tc 12 VA13
5
EC
B−Y
11
F00007
Tc
DLC1
E1
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
DI−233
1996 LAND CRUISER (RM451U)
Tc Terminal Circuit
CIRCUIT DESCRIPTION
Connecting terminals Tc and E1 of the DLC1 causes the ECU to display the DTC by flashing the ABS warni\
ng
light.
WIRING DIAGRAM
INSPECTION PROCEDURE
1 Check voltage between terminals Tc and E1 of DLC1.
CHECK:
(a) Turn the ignition switch ON.
(b) Measure the voltage between terminals Tc and E
1 of the
DLC1.
OK:
Voltage: 10 − 14 V
OK If ABS warning light does not blink even after Tc and E
1 are connected, ECU may be defective.
NG
DI5ML−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5Q3−02
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
DI−243
1996 LAND CRUISER (RM451U)
DIAGNOSTIC TROUBLE CODE CHART
If a malfunction code is displayed during the DTC check, the circuit listed for that code in t\
he table below
(Proceed to the page given for that circuit.).
DTC No.
(See Page)Detection ItemTrouble AreaSRS
Warning Light
Normal
( DI−271 )System normal−OFF
Source voltage dropBattery
 Airbag sensor assemblyON
11
( DI−247 )
Short in squib circuit (to ground)Steering wheel pad (D squib)
 Front passenger airbag assembly (P squib )
 Spiral cable
 Airbag sensor assembly
 Wire harness
ON
12
( DI−254 )
Short in squib circuit (to B+)Steering wheel pad (D squib)
 Front passenger airbag assembly (P squib)
 Spiral cable
 Airbag sensor assembly
 Wire harness
ON
14
( DI−260 )
Open in D squib circuitSteering wheel pad (D squib)
 Spiral cable
 Airbag sensor assembly
 Wire harness
ON
31
( DI−265 )Airbag sensor assembly malfunctionAirbag sensor assemblyON
54
( DI−267 )Open in P squib circuitFront passenger airbag assembly (P squib)
 Airbag sensor assembly
 Wire harness
ON
HINT:
When the SRS warning light remains lit up and the DTC is the normal code\
, this means a source drop
voltage.
This malfunction is not stored in memory by the airbag sensor assembly a\
nd if the power source volt-
age returns to normal, the SRS warning light will automatically go out.
When 2 or more codes are indicated, the codes will be displayed in numer\
al order starting from the
lowest numbered code.
If a code not listed on the chart is displayed, the airbag sensor assemb\
ly is faulty.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5Q6−01
DI−246
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
1996 LAND CRUISER (RM451U)
PROBLEM SYMPTOMS TABLE
Proceed with troubleshooting of each circuit in the table below.
SymptomSuspect AreaSee page
With the ignition switch at ACC or ON, the SRS warning light
sometimes lights up after approx. 6 seconds have elapsed.
 SRS warning light lights up even when ignition switch is in the
LOCK position.
SRS warning light system malfunction
(Always lit up when ignition switch is in LOCK position.)DI−274
With the ignition switch at ACC or ON, the SRS warning lights
does not light up.SRS warning light system malfunction
(Does not light up when ignition switch is turned to ACC or
ON.)
DI−276
DTC not displayed.
 SRS warning light is always lit up with a DTC check procedure.
 DTC displayed without Tc and E1 terminal connection.
Tc terminal circuitDI−279
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

R14285 AB0119H00021
Airbag Sensor Assembly
ON
IG2
ACC
(+)
(−)
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
DI−265
1996 LAND CRUISER (RM451U)
DTC 31 Airbag Sensor Assembly Malfunction
CIRCUIT DESCRIPTION
The airbag sensor assembly consists of a airbag sensor, safing sensor, drive circuit, diagnosis circuit and
ignition control, etc.
It receives signals from the airbag sensors, judges whether or not the SRS must be activated, and diagnosis
system malfunction.
DTC 31 is recorded when occurrence of a malfunction in the airbag sensor\
assembly is detected.
DTC No.DTC Detection ConditionTrouble Area
31 Airbag sensor assembly malfunctionAirbag sensor assembly
INSPECTION PROCEDURE
HINT:
When a malfunction code other than code 31 is displayed at the same time, fi\
rst repair the malfunction indi-
cated by the malfunction code other than code 31.
1 Preparation (See step 1 on page DI−271).
2 Check voltage at IG2 and ACC of airbag sensor assembly.
PREPARATION:
Turn ignition switch ON.
CHECK:
Measure voltage between terminals IG2 and ACC of airbag
sensor assembly and body ground.
OK:
Voltage: Below 16 V
NG Check battery and charging system (See page CH−2).
OK
DI5QA−03
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

R13678
Airbag Sensor
Assembly
Battery F/B
R/B No.2
2
2
1
1
36 4
6 10
9
S4
GR
B
W
L−R
B−L
B−R ACC
IG2
A
IGN
AM1
AM2
FL BLOCK
W−R
B−L
W−R
Ignition
Switch
B
EA2
EA2
4
11 3
CIG
J3 Junction
Connector
GR 4
33
S5 S5
S4
A
2 2
50A AM1
2
2
Short ConnectorGR
B−W
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
DI−271
1996 LAND CRUISER (RM451U)
DTC Normal Source Voltage Drop
CIRCUIT DESCRIPTION
The SRS is equipped with a voltage −increase circuit (DC−DC converter) in the airbag sensor assembly in
case the source voltage drops.
When the battery voltage drops, the voltage −increase circuit (DC−DC converter) functions to increase the
voltage of the SRS to normal voltage.
The diagnosis system malfunction display for this circuit is different to other circuits −when the SRS warning
light remains lit up and the DTC is a normal code, source voltage drop is ind\
icated.
Malfunction in this circuit is not recorded in the airbag sensor assembly, and the source voltage returns to
normal, the SRS warning light automatically goes off.
DTC No.DTC Detection ConditionTrouble Area
NormalSource voltage dorp Battery
 Airbag sensor assembly
WIRING DIAGRAM
DI5QC−03
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

R13679
BatteryFL BLOCK 2
MAIN
W
W
ECU−B
1
F/B
S7
B−R
2
3
SRS Warning
Light
8LA
Tc
B−Y8
IH1 Airbag Sensor
Assembly
DLC1
5 W−L
11
GENERATOR
(ALTERNATOR)
W
Cruise Control ECU
W−L
W−L
B−Y
B−Y
IH1 S7 S6
S6
Short Connector
Short Connector W−L
B−L
11
12
3
EA3 11
22
7
DI−274
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
1996 LAND CRUISER (RM451U)
SRS Warning Light System Malfunction (Always lit up, when igni-
tion switch is in LOCK position.)
CIRCUIT DESCRIPTION
The SRS warning light is located on the combination meter.
When the SRS is normal, the SRS warning light lights up for approx. 6 seconds after the \
ignition switch is
turned from LOCK position to ACC or ON position, and then turns off automatically.
If there is a malfunction in the SRS, the SRS warning light lights up to\
inform the driver of the abnormality.
When terminals Tc and E1 of the DLC1 are connected, the DTC is displayed by the blinking\
of the SRS warn-
ing light.
WIRING DIAGRAM
DI5QD−03
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

N14677
Fuse
DI−276
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
1996 LAND CRUISER (RM451U)
SRS Warning Light System Malfunction (Does not light up, when
ignition switch is turned to ACC or ON.)
CIRCUIT DESCRIPTION
The SRS warning light is located on the combination meter.
When the SRS is normal, the SRS warning light lights up for approx. 6 seconds after the \
ignition switch is
turned from LOCK position to ACC or ON position, and then turns off automatically.
If there is a malfunction in the SRS, the SRS warning light lights up to\
inform the driver of the abnormality.
When terminals Tc and E1 of the DLC1 are connected, the DTC is displayed by the blinking\
of the SRS warn-
ing light.
WIRING DIAGRAM
Refer to page DI−274 for the WIRING DIAGRAM.
INSPECTION PROCEDURE
1 Check ECU−B Fuse.
PREPARATION:
Remove ECU−B fuse.
CHECK:
Check continuity of ECU −B fuse.
OK:
Continuity
HINT:
Fuse may be burnt out even if it appears to be OK during
visual inspection.
If fuse is OK, install it.
NG Go to step 5.
OK
2 Preparation. (See step 1 on page DI−271)
DI5QE−03
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010