display TOYOTA LAND CRUISER 1996 J80 Owner's Guide

R13680
Airbag Sensor
AssemblyTc7
B−L
IH1B−Y
11
3
Tc E 1
DLC1 BR−B
EC
S6
S7 11
B−Y
Short Connector 2
2
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
DI−279
1996 LAND CRUISER (RM451U)
Tc Terminal Circuit
CIRCUIT DESCRIPTION
By connecting terminals Tc and E1 of the DLC1 the airbag sensor assembly is set in the DTC output mode.
The DTCs are displayed by the blinking of the SRS warning light.
WIRING DIAGRAM
DI5QF−03
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AB0117 AB0118 AB0119H00258
LOCKACCON
or
AB0118
R14305 AB0119
H00030
ACCON
or E1Tc
(+)
(−)
DLC1
DI−280
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
If the DTC is not displayed, perform the following troubleshooting.
1 Does SRS warning light light up for approx. 6 seconds?
PREPARATION:
Check operation of SRS warning light after ignition switch is
turned from LOCK position to ACC or ON position.
NO Check SRS warning light system. (See page DI−240 )
YES
2 Check voltage between terminals Tc and E1 of DLC1.
PREPARATION:
Turn ignition switch to ACC or ON.
CHECK:
Measure voltage between terminals Tc and E1 of DLC1.
OK:
Voltage: 10 − 14 V
OK Go to step 4.
NG
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AB0117
R14303H00033
LOCK
Airbag Sensor Assembly
Tc
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
DI−283
1996 LAND CRUISER (RM451U)
If the DTC is displayed without a DTC check procedure, perform the followi\
ng
troubleshooting.
1 Check resistance between terminal Tc of airbag sensor assembly and body
ground.
PREPARATION:
(a) Turn ignition switch to LOCK.
(b) Disconnect negative ( −) terminal cable from the battery,
and wait at least 90 seconds.
(c) Disconnect airbag sensor assembly connector.
CHECK:
Check resistance between terminal Tc of airbag sensor assem-
bly connector and body ground.
OK:
Resistance: 1 MΩ or Higher
NG Repair or replace harness or connector.
OK
Replace airbag sensor assembly.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE4032
BE4033I00021
Normal Code
0.25 sec.
0.25 sec.
ON
OFF
ON
OFF
4 sec. 1.5 sec.
0.5 sec.
2.5 sec.0.5 sec.1.5 sec.
Malfunction codes 11 and 21
Code 11 Code 21
N09348
TOYOTA hand-held tester
TOYOTA Break-out-box
N18670
Instrument Panel Junction Block ECU- B
Fuse
DI-287
-
DIAGNOSTICS CRUISE CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
HINT:
If the DTC is not output, inspect the diagnosis circuit (See page
DI-333 )
As an example, the blinking patterns for codes; normal, 11 and
21 are shown in the illustration.
2. ECU TERMINAL VALUES MEASUREMENT BY USING TOYOTA BREAK-OUT-BOX AND TOYOTA HAND-
HELD TESTER
(a) Hook up the TOYOTA break- out- box and TOYOTA hand-held tester to the vehicle.
(b) Read the ECU input/output values by following the prompts on the tester screen.
(c) Please refer to the TOYOTA hand-held tester has a ºSnapshotº function. This records the measured data and
is effective in the diagnosis of intermittent problems.
3. DTC CLEARANCE
(a) After completing repairs, the diagnostic trouble code re- tained in memory can be cleared by removing the ECU-B
fuse for 10 seconds or more, with the ignition switch off.
(b) Check that the normal code is displayed after connecting the fuse.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

N14305
(1)
(1) (2)
No.
Operation Method CRUISE MAIN Indicator Light
Blinking Pattern Diagnosis
1 Turn SET/COAST switch ON
2 Turn RES/ACC switch ON
3 Turn CANCEL switch ON
Turn stop light switch ON
Depress brake pedal
Turn PNP switch OFF
(Shift to except D position)
4 Drive at about 40 km/h
(25 mph)or higher
Drive at about 40 km/h
(25 mph) or below
Light
ON
OFF
Light ON
OFF
Light ON
OFF Switch ON
Switch OFF
LightON
OFF Switch OFF
Switch ONSET/COAST switch circuit
is normal
RES/ACC switch circuit
is normal
CANCEL switch circuit
is normalStop light switch circuit
is normal
PNP switch circuit is
normal
Vehicle Speed Sensor is
normal
Light ON
OFF
Light
ON
OFF
1sec.
0.25 sec. 0.25 sec.
-
DIAGNOSTICS CRUISE CONTROL SYSTEM
DI-290
1996 LAND CRUISER (RM451U)
5. INPUT SIGNAL CHECK
HINT:
(1) For check No.1 - No.3

Turn ignition switch ON.
(2) For check No.4

Jack up the vehicle.

Start the engine.

Shift to D position.
(a) Press the control switch to SET/COAST or RES/ACC position and hold it down or hold it up º1º.
(b) Push the main switch ON º2º.
(c) Check that the CRUISE MAIN indicator light blinks twice or 3 times repeatedly after 3 seconds.
(d) Turn the SET/COAST or RES/ACC switch OFF.
(e) Operate each switch as listed in the table below.
(f) Read the blinking pattern of the CRUISE MAIN indicator light.
(g) After performing the check, turn the main switch OFF.
HINT:
When 2 or more signals are input to the ECU, the lowest num-
bered code will be displayed first.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5O7−02
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
DI−291
1996 LAND CRUISER (RM451U)
DIAGNOSTIC TROUBLE CODE CHART
If a malfunction code is displayed during the DTC check, check the circuit listed for that cod\
e in the table
below and proceed to the appropriate page.
DTC No.
(See Page)Circuit inspectionTrouble Area
11
( DI−296 )Actuator Motor Circuit
Actuator motor
 Harness or connector between cruise control ECU and
actuator motor
 Cruise control ECU
12
( DI−298 )Actuator Magnetic Clutch Circuit
STOP Fuse
 Stop light switch
 Actuator magnetic clutch
 Harness or connector between cruise control ECU and
actuator magnetic clutch, actuator magnetic clutch and body
ground
 Cruise control ECU
13
( DI−301 )Actuator Position Sensor Circuit
Actuator position sensor
 Harness or connector between cruise control ECU and
actuator position sensor
 Cruise control ECU
14
( DI−304 )Actuator Mechanical Malfunction
Actuator motor (actuator lock: motor, arm)
 Harness or connector between cruise control ECU and
actuator motor
 Cruise control ECU
21
( DI−306 )Open in Vehicle Speed Sensor Circuit
Combination meter
 Harness or connector between cruise control ECU and com-
bination meter, combination meter and vehicle speed sensor
 Vehicle speed sensor
 Cruise control ECU
23
( DI−310 )Vehicle Speed Signal AbnormalVehicle speed sensor
 Cruise control ECU
32
( DI−311 )Control Switch Circuit
Cruise control switch
 Harness or connector between cruise control ECU and cruise
control switch, cruise control switch and body ground
 Cruise control ECU
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010