oil TOYOTA LAND CRUISER 1996 J80 Workshop Manual
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 1996, Model line: LAND CRUISER, Model: TOYOTA LAND CRUISER 1996 J80Pages: 1399, PDF Size: 41.35 MB
Page 1386 of 1399
TR0BE−01
Z18836
Front Output Shaft
Dust Deflector
Oil Seal Housing Ball Bearing
Snap Ring Drive Clutch Hub
Snap Ring
Snap Ring
−
TRANSFER FRONT EXTENSION HOUSING
TR−25
835
Author: Date:
1996 LAND CRUISER (RM451U)
FRONT EXTENSION HOUSING
COMPONENTS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 1387 of 1399
TR0BF−01
Q07133
SST
TF0938
TF0940
SST
TR−26
−
TRANSFER FRONT EXTENSION HOUSING
1996 LAND CRUISER (RM451U)
DISASSEMBLY
1. REMOVE DRIVE CLUTCH HUB
(a) Using a snap ring expander, remove the snap ring.
(b) Using SST, remove the drive clutch hub. SST 09950−40010
2. REMOVE FRONT OUTPUT SHAFT
Using a plastic hammer, drive out the front output shaft.
3. REMOVE DUST DEFLECTOR
(a) Using SST and a press, remove the dust deflector. SST 09950−00020
(b) Using a screwdriver and hammer, tap the dust deflector
and remove it from the extension housing.
4. REMOVE OIL SEAL
Using a screwdriver, pry out the oil seal from the front extension
housing.
5. REMOVE BALL BEARING
(a) Using a screwdriver, remove the snap ring.
(b) Using SST and a press, remove the ball bearing. SST 09316−60011 (09316 −00011, 09316−00071)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 1388 of 1399
TR0BG−01
TF0967
SST
TF0943
SST
TF0939
TF0945
SST
−
TRANSFER FRONT EXTENSION HOUSING
TR−27
1996 LAND CRUISER (RM451U)
REASSEMBLY
HINT:
Coat all of the sliding and rotating surfaces with gear oil before
assembly.
1. INSTALL DUST DEFLECTOR
(a) Using SST and a press, install a new dust deflector to the
front extension housing.
SST 09223−15020, 09950 −70010 (09951−07150)
(b) Using SST and a press, install a new dust deflector to the
front output shaft.
SST 09316−20011, 09316 −60011 (09316−00011)
2. INSTALL BALL BEARING
(a) Using SST and a press, install the ball bearing to the front
extension housing.
SST 09316−60011 (09316 −00011, 09316−00031)
(b) Select a snap ring that will allow minimum axial play.
MarkThickness mm (in.)
A1.7 (0.0669)
B1.8 (0.0709)
(c) Using a screwdriver, install a new snap ring.
3. INSTALL OIL SEAL
Using SST and a hammer, drive in a new oil seal to the front ex-
tension housing.
SST 09316−60011 (09316 −00011, 09316−00061)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 1390 of 1399
TR0BH−01
Q08383
Center Differential Control
Couping Assembly
Snap ring Vehicle Speed sensor
Drive Gear Ball Bearing
Snap Ring
Snap Ring
Oil Pump Plate
Drive Rotor
Oil Pump Cover
Rear Extension housing
Oil Pump Drive Shaft Ball
Spring
Screw Plug
Valve Seat
Dust Deflector
Oil Seal Seal Ring
Rear Output Shaft
Non− reusable Part
Precoated part Separator
Driven Rotor
−
TRANSFER REAR EXTENSION HOUSING
TR−29
839
Author: Date:
1996 LAND CRUISER (RM451U)
REAR EXTENSION HOUSING
COMPONENTS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 1391 of 1399
TR0BI−01
Q00530
Q08384
Q02549
Q07138
TR−30
−
TRANSFER REAR EXTENSION HOUSING
1996 LAND CRUISER (RM451U)
DISASSEMBLY
1. REMOVE OIL PUMP DRIVE SHAFT
2. REMOVE OIL PUMP COVER
(a) Using a torx socket wrench (T30), remove the 3 screws.
(b) Install the 2 suitable bolts to the pump cover.
(c) Remove the pump cover from the rear extension housing.
3. REMOVE DRIVE ROTOR FROM DRIVEN ROTOR
4. REMOVE DRIVEN ROTOR FROM REAR EXTENSION HOUSING
5. REMOVE SCREW PLUG, SPRING, BALL AND VALVE SEAT
(a) Using a hexagon wrench, remove the screw plug.
(b) Using a magnetic finger, remove the spring, ball and valve
seat from the rear extension housing.
6. REMOVE CENTER DIFFERENTIAL CONTROL COU- PLING ASSEMBLY
(a) Using a snap ring expander, remove the snap ring.
(b) Remove the coupling assembly from the rear extension housing.
7. REMOVE SEPARATOR AND OIL PUMP PLATE
Remove the 3 bolts, separator and oil pump plate.
8. REMOVE VEHICLE SPEED SENSOR DRIVE GEAR
(a) Using a snap ring expander, remove the snap ring.
(b) Remove the vehicle speed sensor drive gear.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 1392 of 1399
TF0959
SST
Q08385
Q08481
SST
−
TRANSFER REAR EXTENSION HOUSING
TR−31
1996 LAND CRUISER (RM451U)
9. REMOVE REAR OUTPUT SHAFT
(a) Using a snap ring expander, remove the snap ring.
(b) Using SST and a hammer, remove the rear output shaft.
SST 09325−12010
(c) Remove the 2 seal rings from the rear output shaft.
10. REMOVE DUST DEFLECTOR
(a) Using a screwdriver and hammer, remove the rear exten-
sion housing dust deflector.
(b) Using a screwdriver and hammer, remove the rear output
shaft dust deflector.
11. REMOVE OIL SEAL
Using a screwdriver, pry out the oil seal from the rear extension
housing.
12. REMOVE BALL BEARING
(a) Using a screwdriver, remove the snap ring.
(b) Using SST and a press, remove the ball bearing to the rear extension housing.
SST 09316−60011 (09316 −00011, 09316−00021)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 1393 of 1399
TR0BJ−01
Q02615
Q02616
Q02617
TR−32
−
TRANSFER REAR EXTENSION HOUSING
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT DRIVEN ROTOR BODY CLEARANCE
(a) Install the drive rotor to the driven rotor.
(b) Using a feeler gauge, measure the body clearance be- tween the drive rotor and extension housing.
Standard body clearance:
0.08−0.17 mm (0.0031 −0.0067 in.)
Maximum body clearance: 0.17 mm (0.0067 in.)
If the body clearance exceeds the maximum, replace the drive
rotor or driven rotor.
2. INSPECT DRIVEN ROTOR TIP CLEARANCE
Using a feeler gauge, measure the tip clearance between the
driver rotor and driven rotor. Standard tip clearance:
0.05−0.15 mm (0.0020 −0.0059 in.)
Maximum tip clearance: 0.15 mm (0.0059 in.)
If the tip clearance exceeds the maximum, replace the drive ro-
tor or driven rotor.
3. INSPECT OIL PUMP SIDE CLEARANCE
Using a steel straight edge and feeler gauge, measure the side
clearance of oil pump. Standard side clearance:
0.03−0.10 mm (0.0012 −0.0039 in.)
Maximum side clearance: 0.10 mm (0.0039 in.)
If the side clearance exceeds the maximum, replace the drive
rotor or driven rotor.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 1394 of 1399
TR0CO−01
TF0964
SST
TF0962
Q08482
SST
TF0967
SST
Q08482
SST
−
TRANSFER REAR EXTENSION HOUSING
TR−33
1996 LAND CRUISER (RM451U)
REASSEMBLY
HINT:
Coat all of the sliding and rotating surfaces with gear oil before
assembly.
1. INSTALL BALL BEARING
(a) Using SST and a press, install the ball bearing.
SST 09316−60011 (09316 −00011, 09316−00031)
(b) Select a snap ring that will allow minimum axial play.
MarkThickness mm (in.)
A1.7 (0.0669)
B1.8 (0.0709)
(c) Using a screwdriver, install a new snap ring.
2. INSTALL DUST DEFLECTOR
(a) Using SST and a hammer, install a new rear extension housing dust deflector.
SST 09316−60011 (09316 −00011, 09316−00041)
(b) Using SST and a press, install a new rear output shaft dust deflector.
SST 09316−20011, 09316 −60011 (09316−00011)
3. INSTALL OIL SEAL
Using SST and a hammer, drive in a new oil seal. SST 09316−60011 (09316 −00011, 09316−00031)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 1395 of 1399
TF0969
SST
TF0958
Q07138
Q02549
Q08384
TR−34
−
TRANSFER REAR EXTENSION HOUSING
1996 LAND CRUISER (RM451U)
4. INSTALL REAR OUTPUT SHAFT
(a) Using SST and a press, install the rear output shaft.
SST 09316−20011, 09316 −60011 (09316−00011,
09316 −00031)
(b) Install the 2 seal rings to the rear output shaft.
(c) Select a snap ring that will allow minimum axial play.
MarkThickness mm (in.)
11.95 (0.0768)
22.05 (0.0807)
32.15 (0.0847)
42.25 (0.0886)
(d) Using a snap ring expander, install a new snap ring.
5. INSTALL VEHICLE SPEED SENSOR DRIVE GEAR
(a) Install the vehicle speed sensor drive gear.
(b) Using a snap ring expander, install the snap ring.
6. INSTALL OIL PUMP PLATE AND SEPARATOR
(a) Install the oil pump plate.
(b) Install the separator.
(c) Install and torque the 3 bolts. Torque: 4.9 N·m (50 kgf·cm, 43 in.·lbf)
7. INSTALL CENTER DIFFERENTIAL CONTROL COU- PLING ASSEMBLY
(a) Install the coupling assembly to the output shaft.
(b) Using a snap ring expander, install the snap ring.
8. INSTALL VALVE SEAT, BALL, SPRING AND SCREW PLUG
(a) Apply gear oil to the ball.
(b) Install the valve seat, ball and spring.
(c) Apply liquid sealer to the screw plug.
Sealant: Part No. 08833−00080, THREE BOND 1344,
LOCTITE 242 or equivalent
(d) Using a hexagon wrench, install and torque the screw plug.
Torque: 29 N·m (300 kgf·cm, 22 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 1396 of 1399
TF0977
Q00529
−
TRANSFER REAR EXTENSION HOUSING
TR−35
1996 LAND CRUISER (RM451U)
9. INSTALL DRIVEN ROTOR
(a) Apply gear oil to the driven rotor.
(b) Install the driven rotor.
10. INSTALL DRIVE ROTOR
(a) Apply gear oil to the drive rotor.
(b) Install the drive rotor.
HINT:
Align the alignment marks.
11. INSTALL OIL PUMP COVER
(a) Install the oil pump cover.
(b) Using a torx socket wrench (T30), install and torque the
3 screws.
Torque: 4.9 N·m (50 kgf·cm, 43 in.·lbf)
NOTICE:
Align the oil hole of the rear extension housing and oil
groove end of the oil pump cover.
12. INSTALL OIL PUMP DRIVE SHAFT
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010