Fuse a TOYOTA LAND CRUISER 1996 J80 Repair Manual

Q08580
R-W
J1
A
W 5BRY
IG3
O
Ignition Switch
Fuse Block
GAUGE
(*) Pattern Select Switch
(2nd Start Switch)
B
ECM
18
IH2 12
HI
1
113
9
E4
2
C12
Battery
FL AM1
Fuse Block
B-L
W
B-Y
2
4
F6
6 A
A
Y
3
1
E4HOLD
2
EA2
AM1
22
1
AM1 IG1
B
C12
IG3 IL2
O
R-W
2 2
3
42nd STRT Indicator Light
(Combination Meter)
12
Y
R/B No.2 R/B No.2
DI-185
-
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
Pattern Select Switch Circuit (2nd Start Switch) & 2nd Start
Switch Indicator Light Circuit
CIRCUIT DESCRIPTION
When 2nd start mode is selected with the pattern select switch, the ECM cont\
rols the solenoid valves and
the transmission starts from 2nd gear.
In D position, the transmission automatically shifts up through 3rd to O\
/D as usual.
In 2nd position, the transmission is held in 2nd gear.
WIRING DIAGRAM
(*) Pattern Select Switch (2nd Start Switch)
When the 2nd start switch is pushed, the switch is contacted and the 2nd\
mode is selected.
To cancel the 2nd start, push the 2nd start switch once again. The 2nd sta\
rt is automatically cancelled out
when the ignition switch is turned OFF.
DI5L8-02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

R01346
Normal Code
0.25 sec.
0.25 sec.
2 sec.
ON
OFF
ON
OFF 0.5 sec. 0.5 sec.
Code 11 and 21
4 sec.
1.5 sec.
2.5 sec.
Code 11 Code 21
BR1804
F00006DLC1 Short Pin
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
DI−191
1996 LAND CRUISER (RM451U)
As an example, the blinking patterns for normal code and
codes 11 and 21 are shown in the illustration.
(6) Code are explained in the code table on page
DI−196 .
(7) After completing the check, disconnect terminals Tc
and E
1, and turn off the display.
If 2 or more malfunctions are indicated at the same time the low-
est numbered DTC will be displayed 1st.
(c) Clear the DTC.
(1) Confirm that the center differential is free.
(2) Using SST, connect terminals Tc and E
1 of the
DLC1 and remove the short pin from the DLC1.
SST 09843−18020
(3) Turn the ignition switch ON.
(4) Clear the DTC stored in ECU by depressing the
brake pedal 8 or more times within 3 seconds.
(5) Check that the warning light shows the normal
code.
(6) Remove the SST from the terminals of the DLC1.
SST 09843−18020
(7) Connect the short pin to the DLC1.
HINT:
Cancellation can also be done by removing the ECU −B fuse,
but in this case, other memory systems will also be cancelled
out.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

W02206
Fuse BlockECU−IG
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
DI−217
1996 LAND CRUISER (RM451U)
4 Check ECU −IG fuse.
PREPARATION:
Remove the ECU−IG fuse from the Fuse block.
CHECK:
Check the continuity of the ECU −IG fuse.
OK:
Continuity
NG Check for short in all harness and components connected to ECU −IG fuse (See attached wiring
diagram).
OK
Check for open in harness and connector be-
tween ABS ECU and battery
(See page
IN−28).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−226
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
1 Is DTC output?
Check DTC on page DI−190 .
YES Repair circuit indicated by code output.
NO
2 Is normal code displayed?
YES Check ABS solenoid relay. Check for short in harness and connector between ABS solenoid
relay and DLC1 (See page IN−28 ).
NO
3 Is ABS warning light go off?
YES Check for open or short in harness and connec-
tor between ECU−IG fuse and ECU (See page
IN−28 ).
NO
4 Check battery positive voltage.
PREPARATION:
Start the engine.
CHECK:
Check the battery positive voltage.
OK:
Voltage: 10 − 16 V NG Check and repair charging system.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5Q5−02
W02056
1
2
3
4
567
8910 A
B
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
DI−245
1996 LAND CRUISER (RM451U)
TERMINALS OF ECM
No.SymbolTerminal Name
A−Electrical Connection Check Mechanism
B−Electrical Connection Check Mechanism
1P−Squib  (Passenger)
2P+Squib  (Passenger)
3D−Squib  (Driver)
4D+Squib  (Driver)
5E1Ground
6E2Ground
7TcDiagnosis
8LASRS Warning Light
9IG2Power Source (IGN Fuse)
10ACCPower Source (CIG Fuse)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

N14677
Fuse
DI−276
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
1996 LAND CRUISER (RM451U)
SRS Warning Light System Malfunction (Does not light up, when
ignition switch is turned to ACC or ON.)
CIRCUIT DESCRIPTION
The SRS warning light is located on the combination meter.
When the SRS is normal, the SRS warning light lights up for approx. 6 seconds after the \
ignition switch is
turned from LOCK position to ACC or ON position, and then turns off automatically.
If there is a malfunction in the SRS, the SRS warning light lights up to\
inform the driver of the abnormality.
When terminals Tc and E1 of the DLC1 are connected, the DTC is displayed by the blinking\
of the SRS warn-
ing light.
WIRING DIAGRAM
Refer to page DI−274 for the WIRING DIAGRAM.
INSPECTION PROCEDURE
1 Check ECU−B Fuse.
PREPARATION:
Remove ECU−B fuse.
CHECK:
Check continuity of ECU −B fuse.
OK:
Continuity
HINT:
Fuse may be burnt out even if it appears to be OK during
visual inspection.
If fuse is OK, install it.
NG Go to step 5.
OK
2 Preparation. (See step 1 on page DI−271)
DI5QE−03
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−278
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
1996 LAND CRUISER (RM451U)
5 Is new ECU−B fuse burnt out again?
NO Using simulation method, reproduce malfunc-
tion symptoms (See page IN−18 ).
YES
Check harness between ECU −B fuse and
SRS warning light.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE4032
BE4033I00021
Normal Code
0.25 sec.
0.25 sec.
ON
OFF
ON
OFF
4 sec. 1.5 sec.
0.5 sec.
2.5 sec.0.5 sec.1.5 sec.
Malfunction codes 11 and 21
Code 11 Code 21
N09348
TOYOTA hand-held tester
TOYOTA Break-out-box
N18670
Instrument Panel Junction Block ECU- B
Fuse
DI-287
-
DIAGNOSTICS CRUISE CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
HINT:
If the DTC is not output, inspect the diagnosis circuit (See page
DI-333 )
As an example, the blinking patterns for codes; normal, 11 and
21 are shown in the illustration.
2. ECU TERMINAL VALUES MEASUREMENT BY USING TOYOTA BREAK-OUT-BOX AND TOYOTA HAND-
HELD TESTER
(a) Hook up the TOYOTA break- out- box and TOYOTA hand-held tester to the vehicle.
(b) Read the ECU input/output values by following the prompts on the tester screen.
(c) Please refer to the TOYOTA hand-held tester has a ºSnapshotº function. This records the measured data and
is effective in the diagnosis of intermittent problems.
3. DTC CLEARANCE
(a) After completing repairs, the diagnostic trouble code re- tained in memory can be cleared by removing the ECU-B
fuse for 10 seconds or more, with the ignition switch off.
(b) Check that the normal code is displayed after connecting the fuse.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5O7−02
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
DI−291
1996 LAND CRUISER (RM451U)
DIAGNOSTIC TROUBLE CODE CHART
If a malfunction code is displayed during the DTC check, check the circuit listed for that cod\
e in the table
below and proceed to the appropriate page.
DTC No.
(See Page)Circuit inspectionTrouble Area
11
( DI−296 )Actuator Motor Circuit
Actuator motor
 Harness or connector between cruise control ECU and
actuator motor
 Cruise control ECU
12
( DI−298 )Actuator Magnetic Clutch Circuit
STOP Fuse
 Stop light switch
 Actuator magnetic clutch
 Harness or connector between cruise control ECU and
actuator magnetic clutch, actuator magnetic clutch and body
ground
 Cruise control ECU
13
( DI−301 )Actuator Position Sensor Circuit
Actuator position sensor
 Harness or connector between cruise control ECU and
actuator position sensor
 Cruise control ECU
14
( DI−304 )Actuator Mechanical Malfunction
Actuator motor (actuator lock: motor, arm)
 Harness or connector between cruise control ECU and
actuator motor
 Cruise control ECU
21
( DI−306 )Open in Vehicle Speed Sensor Circuit
Combination meter
 Harness or connector between cruise control ECU and com-
bination meter, combination meter and vehicle speed sensor
 Vehicle speed sensor
 Cruise control ECU
23
( DI−310 )Vehicle Speed Signal AbnormalVehicle speed sensor
 Cruise control ECU
32
( DI−311 )Control Switch Circuit
Cruise control switch
 Harness or connector between cruise control ECU and cruise
control switch, cruise control switch and body ground
 Cruise control ECU
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5O8−02
I00756
DLC1
Cruise Control Actuator
 Actuator Motor
 Actuator Magnetic Clutch
 Actuator Position Sensor
Cruise Control ECU
Cruise Control Switch
 Main Switch
 Control Switch
Stop Light Switch
No.1 V ehicle Speed Sensor
Park/Neutral Position Switch
Instrument Panel Fuse Block

GAUGE Fuse
 ECU−IG Fuse
 ECU− B Fuse
DI−292
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
PARTS LOCATION
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010