ignition TOYOTA LAND CRUISER 1996 J80 Manual Online

P24677
32
4
10 98 6
51
7
A00188
ON
NSW
(+)
(−)
BE6653
P24678
−
DIAGNOSTICS ENGINE
DI−109
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
1 Check park/neutral position switch.
PREPARATION:
Disconnect park/neutral position switch connector.
CHECK:
Check continuity between each terminal shown below when the
shift lever is positioned to each range.
OK:
Shift PositionTerminal No. to continuityTerminal No. to continuity
P4 − 75 − 6
R4 − 8−
N4 − 105 − 6
D4 − 9−
22 − 4−
L3 − 4−
NG Replace park/neutral position switch.
OK
2 Check voltage between terminal NSW of ECM connector and body ground.
PREPARATION:
Remove instrument panel speaker No.1 panel
(See page SF−65 ).
CHECK:
(a) Turn ignition switch ON.
(b) Measure voltage between terminal NSW of ECM connec-
tor and body ground when the shift lever is positioned to
the following positions.
OK:
Shift lever positionP or NL, 2, D or R
Voltage0 V9 − 14 V
OK Check and replace ECM (See page IN−28 ).
NG
Check for open and short in harness and
connector between ECM and park/neutral
position switch (See page IN−28).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

S00816
BatteryFusible
Link
F8F7
11
W−R
3EA2
W−R11 6
IG Switch B−R
Fuse BlockIGN B−L
22
22 2
2
EFI Main Relay
1
2
3 4
EFI R
−Y
EC
EB
B−R
1EB1
R
Y−R
Y−REA2IH1
22 7
BR−B E4
E7 E7 E7
IGSW
MRLY
+B
E1 B+
ECM
1
3
12
24FL AM2
FL MAIN
W R
R/B No.2 Y
DI−11 0
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
ECM Power Source Circuit
CIRCUIT DESCRIPTION
When the ignition switch is turned ON, battery positive voltage is applied t\
o the coil, closing the contacts of
the EFI main relay (Marking: EFI) and supplying power to the terminals +B\
of the ECM.
WIRING DIAGRAM
DI5PX−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00189
ON
E1 +B
(−) (+)
BE6653
P24679
A00190
ON
IGSW
(+)
(−)
BE6653
P24680
−
DIAGNOSTICS ENGINE
DI−111
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
1 Check voltage between terminals +B and E1 of the ECM connector.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel
(See page SF−65 ).
(b) Turn ignition switch ON.
CHECK:
Measure voltage between terminals +B and E1 of the ECM con-
nector.
OK:
Voltage: 9 − 14 V
OK Proceed to next circuit inspection shown on matrix chart (See page DI−19 ).
NG
2 Check for open in harness and connector between terminal E1 of ECM conne\
ctor and body ground (See page IN−28).
NG Repair or replace harness or connector.
OK
3 Check voltage between terminal IGSW of ECM connector and body ground.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel (See page SF−65 ).
(b) Turn ignition switch ON.
CHECK:
Measure voltage between terminals IGSW of ECM and body
ground.
OK:
Voltage: 9 − 14 V
OK Go to step 6.
NG
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P24681
DI−11 2
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
4 Check IGN fuse from fuse block.
NG Check for short in all the harness and
components connected to IGN fuse.
OK
5 Check ignition switch.
PREPARATION:
(a) Remove instrument lower finish panel.
(b) Remove instrument cluster finish center panel No.2.
CHECK:
Check continuity between terminals.
OK:
Shift PositionTerminal No. to continuityTerminal No. to continuity
LOCK−−
ACC3 − 4−
ON2 − 3 − 46 − 11
START1 − 2 − 45 − 6 − 11
NG Replace ignition switch.
OK
Check for open and short in harness and
connector between battery and ignition
switch and ECM.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00191
ONMRLY(+)
(−)
BE6653
P24682
−
DIAGNOSTICS ENGINE
DI−11 3
1996 LAND CRUISER (RM451U)
6 Check voltage between terminal MREL of ECM connector and body ground.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel
(See page SF−65 ).
(b) Turn ignition switch ON.
CHECK:
Measure voltage between terminal MREL of ECM and body
ground.
OK:
Voltage: 9 − 14 V
NG Check and replace ECM.
OK
7 Check EFI fuse (Marking: EFI) (See page DI−105).
NG Check for short in all the harness and
components connected to EFI fuse.
OK
8 Check EFI main relay (Marking: EFI) (See page SF−54).
NG Replace EFI main relay (Marking: EFI).
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P09401
−
DIAGNOSTICS ENGINE
DI−11 7
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
TOYOTA hand −held tester
1 Connect the TOYOTA hand −held tester and check operation of fuel pump.
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect the TOYOTA hand−held tester to the DLC3.
(c) Turn ignition switch ON and TOYOTA hand −held tester
main switch ON.
(d) Use ACTIVE TEST mode to operate the fuel pump.
CHECK:
Check for fuel pressure in the fuel return hose when it is pinched
off.
OK:
There is pressure in the fuel return hose.
HINT:
At this time, you will hear a fuel flowing noise.
OK Go to step 4.
NG
2 Check circuit opening relay (See page SF−56 ).
NG Replace circuit opening relay.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00192
ONFC
(+)
(−)
BE6653
P24684
DI−11 8
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
3 Check voltage between terminal FC of ECM connector and body ground.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel (See page
SF−65 ).
(b) Turn ignition switch ON.
CHECK:
Measure voltage between terminal FC of ECM and body
ground.
OK:
Voltage: 9 − 14 V
OK Go to step 5.
NG
Check for open and short in harness and connector between terminal FC of ECM a\
nd circuit open-
ing relay and fuse block (See page IN−28).
4 Connect the TOYOTA hand−held tester and check operation of fuel pump relay.
PREPARATION:
(a) Connect the TOYOTA hand−held tester to the DLC3.
(b) Start the engine.
(c) Turn TOYOTA hand−held tester main switch ON.
(d) Select the ACTIVE TEST mode on the TOYOTA hand−held tester.
CHECK:
Check operation of fuel pump relay when it is switched ON and OFF by the\
TOYOTA hand −held tester.
OK:
Operating noise can be heard from the relay.
OK Go to step 8.
NG
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00194
HighLowFPR
P22900
P09401
DI−120
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
7 Check for open and short in harness and connector between terminal FPR of
ECM connector and fuel pump relay (See page IN−28).
NG Repair or replace harness or connector.
OK
8 Check operation of fuel pump.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel (See page
SF−65 ).
(b) Connect the TOYOTA hand − held tester to the DLC3.
(c) Turn ignition switch ON and TOYOTA hand −held tester
main switch ON.
(d) Use ACTIVE TEST mode to operate the fuel pump.
CHECK:
Check operation of fuel pump, when it is operated by the TOYO-
TA hand− held tester and terminal FPR of ECM is grounded and
is not grounded.
OK:
There is pressure in the inlet hose.
HINT:
At this time, you will hear a fuel flowing noise.
FPR is grounded
(Low speed)FPR is not grounded (High speed)
NGNGGo to step 9
NGOKGo to step 10
OKNG
Repair or replace
harness or connector between fuel pump
relay and fuel pump.
9 Check fuel pump (See page SF−6 ).
NG Repair or replace fuel pump.
OK
Check for open or short in harness and connector between EFI main relay (Mark\
ing: EFI) and cir-
cuit opening relay and fuel pump relay and fuel pump and body ground (See p\
age IN−28).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00195
ONFC
BE6653
P22178
P09401
−
DIAGNOSTICS ENGINE
DI−121
1996 LAND CRUISER (RM451U)
10 Check fuel pump resistor. (See page SF−58).
NG Replace fuel pump resistor.
OK
Check for open and short in harness and connector between fuel pump relay and fuel\
pump resis-
tor and fuel pump (See page IN−28).
OBD II scan tool (excluding TOYOTA hand −held tester)
1 Check fuel pump operation.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel (See page
SF−65 ).
(b) Turn ignition switch ON.
CHECK:
(a) Connect between terminal FC of ECM and body ground.
(b) Check for fuel pressure in the fuel inlet hose when it is pinched off.
OK:
There is pressure in the fuel inlet hose.
HINT:
At this time, you will hear a fuel flowing noise.
OK Go to step 4.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00196
ONFC
High LowFPR
BE6653
P22901
P09401
−
DIAGNOSTICS ENGINE
DI−123
1996 LAND CRUISER (RM451U)
7 Check operation of fuel pump.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel (See page
SF−65 ).
(b) Turn ignition switch ON.
CHECK:
(a) Connect terminal FC of ECM and body ground.
(b) Check operation of fuel pump when terminal FPR of ECM
is grounded and is not grounded.
OK:
There is pressure in the inlet hose.
HINT:
At this time, you will hear a fuel flowing noise.
FPR is grounded
(Low speed)FPR is not grounded (High speed)
NGNGGo to step 8
NGOKGo to step 9
OKNG
Repair or replace
harness or connecter between fuel pump
relay and fuel pump.
8 Check fuel pump (See page SF−6 ).
NG Repair or replace fuel pump.
OK
Check for open or short in harness and connector between EFI main relay (Mark\
ing: EFI) and cir-
cuit opening relay and fuel pump relay and fuel pump and body ground (See p\
age IN−28).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010