transaxle TOYOTA RAV4 2006 Service User Guide

PREPARATION – U140F AUTOMATIC TRANSAXLEPP–53
PP
EQUIPMENT
Straight edge -
Vernier calipers -
Dial indicator or dial indicator with magnetic base -
Torque wrench -
Feeler gauge -
Plastic-faced hammer -
Press -
Seal packing 2403, THREE BOND 2403 or equivalent -

PP–54PREPARATION – U140F AUTOMATIC TRANSAXLE
PP
LUBRICANT
Automatic transaxle fluid
Dry fill (w/ Warmer)8.1 liters (8.6 US qts, 7.2 Imp. qts) Toyota Genuine ATF WS
Automatic transaxle fluid
Drain and refill (w/ Warmer)3.5 liters (3.7 US qts, 3.1 Imp. qts)

PREPARATION – U140F AUTOMATIC TRANSAXLEPP–55
PP
SSM
Toyota Genuine Seal Packing 1281
Three Bond 1281 or Equivalent-
Toyota Genuine Adhesive 1344
Three Bond 1344 or Equivalent-

PREPARATION – U241E AUTOMATIC TRANSAXLEPP–59
PP
RECOMMENDED TOOLS
09011-12301 Socket Wrench 30 mm -
09031-00030 Pin Punch -
09040-00011 Hexagon Wrench Set -
(09043-20060) Socket Hexagon Wrench 6 -
(09043-20100) Socket Hexagon Wrench 10 -
09042-00010 Torx Socket T30 -
09904-00010 Expander Set -
09905-00012 Snap Ring No.1 Expander -
09905-00013 Snap Ring Pliers -

PP–60PREPARATION – U241E AUTOMATIC TRANSAXLE
PP
EQUIPMENT
Straight edge -
Vernier calipers -
Dial indicator or dial indicator with magnetic base -
To r q u e w r e n c h -
Feeler gauge -
Plastic-faced hammer -
Press -
Seal packing 2403, THREE BOND 2403 or equivalent -

PREPARATION – U241E AUTOMATIC TRANSAXLEPP–61
PP
LUBRICANT
Automatic transaxle fluid
Dry fill8.1 liters (8.6 US qts, 7.2 Imp. qts) Toyota Genuine ATF WS
Automatic transaxle fluid
Drain and refill3.5 liters (3.7 US qts, 3.1 Imp. qts)

PP–62PREPARATION – U241E AUTOMATIC TRANSAXLE
PP
SSM
Toyota Genuine Seal Packing 1281
Three Bond 1281 or Equivalent-
Toyota Genuine Adhesive 1344
Three Bond 1344 or Equivalent-

U140F AUTOMATIC TRANSAXLE – AUTOMATIC TRANSAXLE SYSTEMAX–3
AX
DEFINITION OF TERMS
Te r m D e f i n i t i o n
Monitor description Description of what the ECM monitors and how it detects malfunctions (monitoring purpose and its details).
Related DTCs Diagnostic code.
Typical enabling conditionPreconditions that allow the ECM to detect malfunctions.
With all preconditions satisfied, the ECM sets the DTC when the monitored value(s) exceeds the
malfunction threshold(s).
Sequence of operationThe priority order that is applied to monitoring, if multiple sensors and components are used to detect the
malfunction.
While another sensor is being monitored, the next sensor or component will not be monitored.
Required sensor/Components The sensors and components that are used by the ECM to detect malfunctions.
Frequency of operationThe number of times that the ECM checks for malfunctions per driving cycle.
"Once per driving cycle" means that the ECM detects malfunction only 1 time during a single driving cycle.
"Continuous" means that the ECM detects a malfunction every time the enabling condition is met.
DurationThe minimum time that the ECM must sense a continuous deviation in the monitored value(s) before
setting a DTC. This timing begins after the "typical enabling conditions" are met.
Malfunction thresholds Beyond this value, the ECM will conclude that there is a malfunction and set a DTC.
MIL operationMIL illumination timing after a defect is detected.
"Immediate" means that the ECM illuminates the MIL the instant the ECM determines that there is a
malfunction.
"2 driving cycle" means that the ECM illuminates the MIL if the same malfunction is detected again in the
2nd driving cycle.
Component operating rangeNormal operation range of sensors and solenoids under normal driving conditions.
Use these ranges as a reference.
They cannot be used to judge if a sensor or solenoid is defective or not.

AX–4U140F AUTOMATIC TRANSAXLE – AUTOMATIC TRANSAXLE SYSTEM
AX
PARTS LOCATION
C127571E01

U140F AUTOMATIC TRANSAXLE – AUTOMATIC TRANSAXLE SYSTEMAX–5
AX
C127581E01