torque TOYOTA RAV4 2006 Service Repair Manual

SB–40SEAT BELT – REAR SEAT INNER BELT ASSEMBLY
SB
12. REMOVE REAR SEAT INNER BELT ASSEMBLY RH
(for 60/40 Split Seat Type LH Side)
(a) Remove the bolt and the seat belt.
13. REMOVE REAR NO. 1 SEAT ASSEMBLY RH (See
page SE-84)
14. REMOVE REAR SEAT INNER BELT ASSEMBLY RH
(for 60/40 Split Seat Type RH Side)
(a) Remove the bolt and the seat belt.
15. REMOVE NO. 2 SEAT HINGE COVER LH (w/ Rear No.
2 Seat) (See page SE-109)
16. REMOVE NO. 2 SEAT LEG COVER (w/ Rear No. 2
Seat) (See page SE-109)
17. REMOVE REAR NO. 2 SEAT ASSEMBLY LH (w/ Rear
No. 2 Seat) (See page SE-110)
18. REMOVE REAR NO. 2 SEAT RECLINING COVER LH
(w/ Rear No. 2 Seat) (See page S E - 111)
19. REMOVE REAR NO. 2 SEAT INNER BELT ASSEMBLY
LH (w/ Rear No. 2 Seat)
(a) Remove the bolt and seat belt.
INSTALLATION
1. INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY
LH (w/ Rear No. 2 Seat)
(a) Install the seat belt with the bolt.
Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
2. INSTALL REAR NO. 2 SEAT RECLINING COVER LH
(w/ Rear No. 2 Seat) (See page SE-121)
3. INSTALL REAR NO. 2 SEAT ASSEMBLY LH (w/ Rear
No. 2 Seat) (See page SE-121)
B138224
B138223
B135675E01
B135676E01

SEAT BELT – REAR SEAT INNER BELT ASSEMBLYSB–41
SB
4. INSTALL NO. 2 SEAT LEG COVER (w/ Rear No. 2
Seat) (See page SE-123)
5. INSTALL NO. 2 SEAT HINGE COVER (w/ Rear No. 2
Seat) (See page SE-123)
6. INSTALL REAR SEAT INNER BELT ASSEMBLY RH
(for 60/40 Split Seat Type RH Side)
(a) Install the belt with the bolt.
Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
7. INSTALL REAR NO. 1 SEAT ASSEMBLY RH (See
page SE-97)
8. INSTALL REAR SEAT INNER BELT ASSEMBLY RH
(for 60/40 Split Seat Type LH Side)
(a) Install the belt with the bolt.
Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
9. INSTALL REAR SEAT LAP TYPE BELT ASSEMBLY
CENTER LH
(a) Install the belt with the bolt.
Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
10. INSTALL REAR SEAT REAR BRACKET COVER LH
(See page SE-60)
11. INSTALL REAR NO. 1 SEAT ASSEMBLY LH (See
page SE-64)
B138223
B138224
B130992

SB–42SEAT BELT – REAR SEAT INNER BELT ASSEMBLY
SB
12. INSTALL REAR SEAT LAP TYPE BELT ASSEMBLY
CENTER RH (w/o Rear No. 2 Seat)
(a) Install the belt with the bolt.
Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
NOTICE:
The anchor part of the seat belt must not overlap
the protruding part.
13. INSTALL REAR SEAT LAP TYPE BELT ASSEMBLY
CENTER RH (w/ Rear No. 2 Seat)
(a) Install the belt with the bolt.
Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
NOTICE:
The anchor part of the seat belt must not overlap
the protruding part.
14. INSTALL REAR NO. 5 SEAT LEG SIDE COVER
15. INSTALL REAR NO. 4 SEAT LEG SIDE COVER
16. INSTALL REAR NO. 3 SEAT LEG SIDE COVER (w/
Rear No. 2 Seat) (See page SE-72)
17. INSTALL REAR NO. 3 SEAT LEG SIDE COVER (w/o
Rear No. 2 Seat) (See page SE-72)
18. INSTALL REAR NO. 2 SEAT LEG SIDE COVER
19. INSTALL REAR SEAT LEG COVER
B138225E01
B131622E01

CRUISE CONTROL – CRUISE CONTROL MAIN SWITCHCC–37
CC
INSTALLATION
1. INSTALL CRUISE CONTROL MAIN SWITCH
(a) Install the switch with the 2 screws.
Torque: 1.7 to 3.0 N*m (17.34 to 30.60 kgf*cm,
15.04 to 26.55 in.*lbf)
(b) Connect the connector.
2. INSTALL STEERING PAD ASSEMBLY (See page RS-
336)
3. CONNECT CABLE TO NEGATIVE BATTERY
TERMINAL
4. CHECK SRS WARNING LIGHT
(a) Check the SRS warning light (see page RS-37).
B127290E08

LIGHTING – FRONT DOOR COURTESY SWITCHLI–141
LI
INSTALLATION
HINT:
• Use the same procedures for the RH and LH sides.
• The procedures listed below are for the LH side.
• A bolt without a torque specification is shown in the
standard bolt chart (see page SS-2).
1. INSTALL FRONT DOOR COURTESY LIGHT SWITCH
ASSEMBLY
(a) Connect the connector.
(b) Install the switch with the bolt.
2. CONNECT CABLE TO NEGATIVE BATTERY
TERMINAL
B131444

LIGHTING – REAR DOOR COURTESY SWITCHLI–143
LI
INSTALLATION
HINT:
• Use the same procedures for the RH and LH sides.
• The procedures listed below are for the LH side.
• A bolt without a torque specification is shown in the
standard bolt chart (see page SS-2).
1. INSTALL REAR DOOR COURTESY LIGHT SWITCH
ASSEMBLY
(a) Connect the connector.
(b) Install the switch with the bolt.
2. CONNECT CABLE TO NEGATIVE BATTERY
TERMINAL
B131445

LIGHTING – BACK DOOR COURTESY SWITCHLI–145
LI
INSTALLATION
HINT:
• Use the same procedures for the RH and LH sides.
• The procedures listed below are for the LH side.
• A bolt without a torque specification is shown in the
standard bolt chart (see page SS-2).
1. INSTALL BACK DOOR COURTESY LIGHT SWITCH
ASSEMBLY
(a) Connect the connector.
(b) Install the switch with the bolt.
2. CONNECT CABLE TO NEGATIVE BATTERY
TERMINAL
B131446

WW–10WIPER AND WASHER – FRONT WIPER MOTOR AND LINK
WW
INSPECTION
1. INSPECT WINDSHIELD WIPER MOTOR ASSEMBLY
(a) Check the LO operation.
(1) Connect the battery's positive (+) lead to
terminal 5 (+1) and the negative (-) lead to
terminal 4 (E), and check that the motor
operates at low speed (LO).
OK:
Motor operates at low speed (LO).
(b) Check the HI operation.
(1) Connect the battery's positive (+) lead to
terminal 3 (+2) and the negative (-) lead to
terminal 4 (E), and check that the motor
operates at high speed (HI).
OK:
Motor operates at high speed (HI).
(c) Check the automatic stop operation.
(1) Connect the battery's positive (+) lead to
terminal 5 (+1) and the negative (-) lead to
terminal 4 (E). With the motor rotating at low
speed (LO), disconnect terminal 5 (+1) to stop
the wiper motor operation at any position other
than the automatic stop position.
(2) Using SST, connect terminals 1 (+S) and 5
(+1). Then connect the battery's positive (+)
lead to terminal 2 (B) and the negative (-) lead
to terminal 4 (E) to restart the motor operation
at low speed (LO).
SST 09843-18040
(3) Check that the motor stops automatically at the
automatic stop position.
OK:
Refer to illustration.
If the result is not as specified, replace the
motor assembly.
INSTALLATION
1. INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY
(a) Install the wiper motor with the 3 bolts.
Torque: 5.4 N*m (55 kgf*cm, 48 in.*lbf)
E034081E21
B131458E01
B136374

WIPER AND WASHER – FRONT WIPER MOTOR AND LINKWW–11
WW
(b) Align the matchmarks on the crank arm and motor.
(c) Apply MP grease to the sliding parts of the wiper
motor and the rod of the wiper link.
(d) Connect the rod of the wiper link to the wiper motor.
2. INSTALL WINDSHIELD WIPER MOTOR AND LINK
ASSEMBLY
(a) Move the wiper motor and link in the direction
shown by the arrow in the illustration to attach the
wiper cushion to the body, and install the wiper
motor and link.
(b) Install the 2 bolts.
Torque: 5.5 N*m (56 kgf*cm, 49 in.*lbf)
(c) Connect the connector.
3. INSTALL COWL TOP VENTILATOR LOUVER
(a) Attach the 12 claws to install the louver.
(b) Install the 2 clips.
4. INSTALL FRONT FENDER TO COWL SIDE SEAL LH
(a) Attach the claw to install the front fender to cowl
side seal.
5. INSTALL FRONT FENDER TO COWL SIDE SEAL RH
(a) Attach the claw to install the front fender to cowl
side seal.
B131466E01
B133583E01
B131453
E125248E01
B133588

WW–12WIPER AND WASHER – FRONT WIPER MOTOR AND LINK
WW
6. INSTALL FRONT WIPER ARM AND BLADE
ASSEMBLY RH
(a) Stop the wiper motor at the automatic stop position.
(b) Clean the wiper arm serration with a round file or
equivalent.
(c) Clean the wiper pivot serration with a wire brush.
(d) Install the arm and blade with the nut. Make sure
that the arm and blade comes to the position shown
in the illustration.
Torque: 21 N*m (214 kgf*cm, 23 ft.*lbf)
HINT:
Hold down the arm hinge with your hand while
tightening the nut.
7. INSTALL FRONT WIPER ARM AND BLADE
ASSEMBLY LH
(a) Clean the wiper arm serration with a round file or
equivalent.
(b) Clean the wiper pivot serration with a wire brush.
E058837E07
B133593E01
E058837E07